Haris Naeem Abbasi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Haris Naeem Abbasi has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Zhenqiang Ma
Department of Electrical and Computer Engineering University of Wisconsin‐Madison Madison Wisconsin USA
6 shared publications - Jiarui Gong
Department of Electrical and Computer Engineering University of Wisconsin‐Madison Madison Wisconsin USA
4 shared publications - Jie Zhou
Department of Electrical and Computer Engineering University of Wisconsin‐Madison Madison Wisconsin USA
4 shared publications - Xin Qi
School of Electrical, Computer and Energy Engineering, Arizona State University 2 , Tempe, Arizona 85287
3 shared publications - Yong-Hang Zhang
School of Electrical, Computer and Energy Engineering, Arizona State University 2 , Tempe, Arizona 85287
3 shared publications - Zheng Ju
School of Electrical, Computer and Energy Engineering, Arizona State University 2 , Tempe, Arizona 85287
3 shared publications
Latest Publications
- Open Access
- 2 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (9)
Band alignment and electrical characterizations of a grafted Si/MgCdTe p–i–n heterojunction
Thin-film solar cells offer high power density and efficiency, making them attractive for terrestrial and space applications. Among these, cadmium telluride (CdTe) is a leading material due to its direct bandgap and high absorption coefficient. However, further improvements in efficiency and open-circuit voltage (Voc) are hindered by intrinsic p-type doping limitations, limiting the built-in potential (Vbi) and the corresponding Voc. To address this, we utilize semiconductor grafting to integrate a single-crystal p-type silicon nanomembrane onto an epitaxial MgCdTe layer, forming a Si/MgCdTe heterojunction while overcoming lattice mismatch constraints. Using x-ray photoelectron spectroscopy, we determine a type-I band alignment with conduction and valence band offsets of 0.66 and 0.45 eV, respectively. Additionally, we fabricate a p–i–n heterojunction diode, demonstrating a satisfying rectification ratio and a moderate ideality factor. This work provides a possible pathway for high-efficiency CdTe-based photovoltaics and Si/MgCdTe tandem cells, leveraging precise band alignment engineering and high p-type doping to enhance Voc in single junction cells and higher-efficiency multijunction cells.
- 2 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (9)
Open AccessBand alignment and electrical characterizations of a grafted Si/MgCdTe p–i–n heterojunction
Thin-film solar cells offer high power density and efficiency, making them attractive for terrestrial and space applications. Among these, cadmium telluride (CdTe) is a leading material due to its direct bandgap and high absorption coefficient. However, further improvements in efficiency and open-circuit voltage (Voc) are hindered by intrinsic p-type doping limitations, limiting the built-in potential (Vbi) and the corresponding Voc. To address this, we utilize semiconductor grafting to integrate a single-crystal p-type silicon nanomembrane onto an epitaxial MgCdTe layer, forming a Si/MgCdTe heterojunction while overcoming lattice mismatch constraints. Using x-ray photoelectron spectroscopy, we determine a type-I band alignment with conduction and valence band offsets of 0.66 and 0.45 eV, respectively. Additionally, we fabricate a p–i–n heterojunction diode, demonstrating a satisfying rectification ratio and a moderate ideality factor. This work provides a possible pathway for high-efficiency CdTe-based photovoltaics and Si/MgCdTe tandem cells, leveraging precise band alignment engineering and high p-type doping to enhance Voc in single junction cells and higher-efficiency multijunction cells.
- Open Access
- 19 November 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (19)
Atomic layer deposition of ultrathin nitride films for enhanced carrier lifetimes and photoluminescence in CdTe/MgCdTe double heterostructures
This work evaluates the passivation effectiveness of ultrathin nitride layers (SiNx, AlN, and TiN) deposited via atomic layer deposition on CdTe/MgCdTe double heterostructures for solar cell applications. Time-resolved photoluminescence and photoluminescence measurements revealed enhanced carrier lifetimes and reduced surface recombination, indicating improved passivation effectiveness. These results underscore the potential of SiNx as a promising passivation material to improve the efficiency of CdTe solar cells.
- 19 November 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (19)
Open AccessAtomic layer deposition of ultrathin nitride films for enhanced carrier lifetimes and photoluminescence in CdTe/MgCdTe double heterostructures
This work evaluates the passivation effectiveness of ultrathin nitride layers (SiNx, AlN, and TiN) deposited via atomic layer deposition on CdTe/MgCdTe double heterostructures for solar cell applications. Time-resolved photoluminescence and photoluminescence measurements revealed enhanced carrier lifetimes and reduced surface recombination, indicating improved passivation effectiveness. These results underscore the potential of SiNx as a promising passivation material to improve the efficiency of CdTe solar cells.
- 2 September 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (10)
Structural and electrical properties of grafted Si/GaAsSb heterojunction
The short-wave infrared (SWIR) wavelength, especially 1.55 μm, has attracted significant attention in various areas such as high-speed optical communication and LiDAR systems. Avalanche photodiodes (APDs) are a critical component as a receiver in these systems due to their internal gain, which enhances the system performance. Silicon-based APDs are promising since they are CMOS compatible, but they are limited in detecting 1.55 μm light detection. This study proposes a p-type Si on n-type GaAs0.51Sb0.49 (GaAsSb) lattice matched to InP substrates heterojunction formed using a grafting technique for future GaAsSb/Si APD technology. A p+Si nanomembrane is transferred onto the GaAsSb/AlInAs/InP substrate, with an ultrathin ALD-Al2O3 oxide at the interface, which behaves as both double-side passivation and quantum tunneling layers. The devices exhibit excellent surface morphology and interface quality, confirmed by atomic force microscope and transmission electron microscope. Also, the current–voltage (I–V) of the p+Si/n−GaAsSb heterojunction shows the rectifying characteristics with an ideality factor of 1.8. The I–V tests across multiple devices confirm high consistency and yield. Furthermore, the x-ray photoelectron spectroscopy measurement reveals that GaAsSb and Si are found to have type-II band alignment with a conduction band offset of 50 meV, which is favorable for the high-bandwidth APD application. The demonstration of the GaAsSb/Si heterojunction highlights the potential to advance current SWIR PD technologies.
- 2 September 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (10)
Structural and electrical properties of grafted Si/GaAsSb heterojunction
The short-wave infrared (SWIR) wavelength, especially 1.55 μm, has attracted significant attention in various areas such as high-speed optical communication and LiDAR systems. Avalanche photodiodes (APDs) are a critical component as a receiver in these systems due to their internal gain, which enhances the system performance. Silicon-based APDs are promising since they are CMOS compatible, but they are limited in detecting 1.55 μm light detection. This study proposes a p-type Si on n-type GaAs0.51Sb0.49 (GaAsSb) lattice matched to InP substrates heterojunction formed using a grafting technique for future GaAsSb/Si APD technology. A p+Si nanomembrane is transferred onto the GaAsSb/AlInAs/InP substrate, with an ultrathin ALD-Al2O3 oxide at the interface, which behaves as both double-side passivation and quantum tunneling layers. The devices exhibit excellent surface morphology and interface quality, confirmed by atomic force microscope and transmission electron microscope. Also, the current–voltage (I–V) of the p+Si/n−GaAsSb heterojunction shows the rectifying characteristics with an ideality factor of 1.8. The I–V tests across multiple devices confirm high consistency and yield. Furthermore, the x-ray photoelectron spectroscopy measurement reveals that GaAsSb and Si are found to have type-II band alignment with a conduction band offset of 50 meV, which is favorable for the high-bandwidth APD application. The demonstration of the GaAsSb/Si heterojunction highlights the potential to advance current SWIR PD technologies.
- 24 June 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (26)
Characteristics of grafted monocrystalline Si/ β -Ga2O3p–n heterojunction
Beta-phase gallium oxide (β-Ga2O3) has exceptional electronic properties with vast potential in power and radio frequency electronics. Despite the excellent demonstrations of high-performance unipolar devices, the lack of effective p-type dopants in β-Ga2O3 has hindered the further development of Ga2O3-based bipolar devices. In this work, we applied the semiconductor grafting approach and fabricated monocrystalline Si/β-Ga2O3p–n heterojunctions, of which the characteristics were systematically studied. The heterojunctions demonstrated a diode rectification over 1.3 × 107 at ±2 V with a diode ideality factor of 1.13. Furthermore, capacitance–voltage (C–V) measurement showed frequency dispersion-free characteristics from 10 to 900 kHz. The interface defect density (Dit) was calculated as 1–3 × 1012/cm2 eV. Scanning transmission electron microscopy (STEM) and x-ray photoelectron spectroscopy (XPS) revealed that an ultrathin oxygen-rich layer existed on the Ga2O3 surface and later formed an ultrathin interfacial layer after bonding with Si. It is speculated that the excessive oxygen at the Ga2O3 surface enhanced the passivation of the Si dangling bonds and thus reduced Dit. This work improved our understanding of interface properties of the semiconductor grafting approach, providing useful guidance on the future development of Si/Ga2O3 heterojunction devices.
- 24 June 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (26)
Characteristics of grafted monocrystalline Si/ β -Ga2O3p–n heterojunction
Beta-phase gallium oxide (β-Ga2O3) has exceptional electronic properties with vast potential in power and radio frequency electronics. Despite the excellent demonstrations of high-performance unipolar devices, the lack of effective p-type dopants in β-Ga2O3 has hindered the further development of Ga2O3-based bipolar devices. In this work, we applied the semiconductor grafting approach and fabricated monocrystalline Si/β-Ga2O3p–n heterojunctions, of which the characteristics were systematically studied. The heterojunctions demonstrated a diode rectification over 1.3 × 107 at ±2 V with a diode ideality factor of 1.13. Furthermore, capacitance–voltage (C–V) measurement showed frequency dispersion-free characteristics from 10 to 900 kHz. The interface defect density (Dit) was calculated as 1–3 × 1012/cm2 eV. Scanning transmission electron microscopy (STEM) and x-ray photoelectron spectroscopy (XPS) revealed that an ultrathin oxygen-rich layer existed on the Ga2O3 surface and later formed an ultrathin interfacial layer after bonding with Si. It is speculated that the excessive oxygen at the Ga2O3 surface enhanced the passivation of the Si dangling bonds and thus reduced Dit. This work improved our understanding of interface properties of the semiconductor grafting approach, providing useful guidance on the future development of Si/Ga2O3 heterojunction devices.
- Open Access
- 3 October 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (13)
Passivation of CdTe/MgCdTe double heterostructure by dielectric thin films deposited using atomic layer deposition
This work reports a study of the passivation effects of different dielectric thin films deposited on monocrystalline CdTe/MgCdTe double heterostructures (DHs) using atomic layer deposition (ALD). Enhanced photoluminescence intensity was observed in all DHs with surface passivation, and increased photogenerated carrier lifetime was observed in DHs with HfO2, TiO2, Al2O3, and TiN passivated CdTe/MgCdTe DHs. These results have demonstrated effective suppression of the undesired surface recombination of CdTe/MgCdTe DHs by dielectric thin films deposited via ALD.
- 3 October 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (13)
Open AccessPassivation of CdTe/MgCdTe double heterostructure by dielectric thin films deposited using atomic layer deposition
This work reports a study of the passivation effects of different dielectric thin films deposited on monocrystalline CdTe/MgCdTe double heterostructures (DHs) using atomic layer deposition (ALD). Enhanced photoluminescence intensity was observed in all DHs with surface passivation, and increased photogenerated carrier lifetime was observed in DHs with HfO2, TiO2, Al2O3, and TiN passivated CdTe/MgCdTe DHs. These results have demonstrated effective suppression of the undesired surface recombination of CdTe/MgCdTe DHs by dielectric thin films deposited via ALD.
- Open Access
- 4 March 2023
- Published by Wiley in Advanced Electronic Materials
- Vol. 9 (5)
Synthesis and Characteristics of Transferrable Single‐Crystalline AlN Nanomembranes
Single‐crystalline inorganic semiconductor nanomembranes (NMs) have attracted great attention over the last decade, which poses great advantages to complex device integration. Applications in heterogeneous electronics and flexible electronics have been demonstrated with various semiconductor nanomembranes. Single‐crystalline aluminum nitride (AlN), as an ultrawide‐bandgap semiconductor with great potential in applications such as high‐power electronics has not been demonstrated in its NM forms. This very first report demonstrates the creation, transfer‐printing, and characteristics of the high‐quality single‐crystalline AlN NMs. This work successfully transfers the AlN NMs onto various foreign substrates. The crystalline quality of the NMs has been characterized by a broad range of techniques before and after the transfer‐printing and no degradation in crystal quality has been observed. Interestingly, a partial relaxation of the tensile stress has been observed when comparing the original as‐grown AlN epi and the transferred AlN NMs. In addition, the transferred AlN NMs exhibits the presence of piezoelectricity at the nanoscale, as confirmed by piezoelectric force microscopy. This work also comments on the advantages and the challenges of the approach. Potentially, the novel approach opens a viable path for the development of the AlN‐based heterogeneous integration and future novel electronics and optoelectronics.
- 4 March 2023
- Published by Wiley in Advanced Electronic Materials
- Vol. 9 (5)
Open AccessSynthesis and Characteristics of Transferrable Single‐Crystalline AlN Nanomembranes
Single‐crystalline inorganic semiconductor nanomembranes (NMs) have attracted great attention over the last decade, which poses great advantages to complex device integration. Applications in heterogeneous electronics and flexible electronics have been demonstrated with various semiconductor nanomembranes. Single‐crystalline aluminum nitride (AlN), as an ultrawide‐bandgap semiconductor with great potential in applications such as high‐power electronics has not been demonstrated in its NM forms. This very first report demonstrates the creation, transfer‐printing, and characteristics of the high‐quality single‐crystalline AlN NMs. This work successfully transfers the AlN NMs onto various foreign substrates. The crystalline quality of the NMs has been characterized by a broad range of techniques before and after the transfer‐printing and no degradation in crystal quality has been observed. Interestingly, a partial relaxation of the tensile stress has been observed when comparing the original as‐grown AlN epi and the transferred AlN NMs. In addition, the transferred AlN NMs exhibits the presence of piezoelectricity at the nanoscale, as confirmed by piezoelectric force microscopy. This work also comments on the advantages and the challenges of the approach. Potentially, the novel approach opens a viable path for the development of the AlN‐based heterogeneous integration and future novel electronics and optoelectronics.
- Open Access
- 4 December 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (25) , 36750-36756
Characterization of UV photodetector based on ZnO/diamond film
In this study, a ZnO/diamond structure ultraviolet (UV) photodetector was fabricated and investigated. ZnO films with thickness of 50 and 100 nm were deposited on half of diamond substrates by sputtering technique. Then, electrodes were patterned on ZnO and diamond areas to form photodetectors. The photocurrent gain in the UV region has been strongly influenced by ZnO film. ZnO films with thickness of 50 and 100 nm on diamond substrates reaches 14.3 and 308 A/W, respectively. Both of peak responsivities were located at 270 nm. Additionally, two shoulder peaks around 240 nm and 290 nm were observed for ZnO/diamond photodetector, which may stem from diamond and ZnO, respectively.
- 4 December 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (25) , 36750-36756
Open AccessCharacterization of UV photodetector based on ZnO/diamond film
In this study, a ZnO/diamond structure ultraviolet (UV) photodetector was fabricated and investigated. ZnO films with thickness of 50 and 100 nm were deposited on half of diamond substrates by sputtering technique. Then, electrodes were patterned on ZnO and diamond areas to form photodetectors. The photocurrent gain in the UV region has been strongly influenced by ZnO film. ZnO films with thickness of 50 and 100 nm on diamond substrates reaches 14.3 and 308 A/W, respectively. Both of peak responsivities were located at 270 nm. Additionally, two shoulder peaks around 240 nm and 290 nm were observed for ZnO/diamond photodetector, which may stem from diamond and ZnO, respectively.