ОКОльга Валеріївна Котульська

Ольга Валеріївна Котульська

*This is an algorithmically generated author record based on publicly available information.

Ольга Валеріївна Котульська has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    APPROXIMATION EQUATIONS OF STEAM STATE IN THE LOW-PRESSURE REGION FOR ANALYSIS OF WORK THE LAST STAGES STEAM TURBINE

    by Oleksandr Shubenko, Volodymyr Goloshchapov, Olga Kotulska, Tetiana Paramonova, Roman Kotulskiy

    The operating conditions of the low-pressure cylinder (LPC) of steam turbines used at thermal and nuclear power plants were analyzed. The LPC stages operate both in the region of superheated steam and in the wet steam region, where phase transition phenomena significantly influence on efficiency and blade erosion. In practical operation, the thermodynamic state of steam is usually determined by using steam tables or complex approximation functions based on tabulated data, which are not always convenient for real-time engineering calculations. Based on the classical ideal gas equation of state and using tabulated thermodynamic properties of water and steam in accordance with IAPWS formulations, approximation equations of state are developed for dry saturated, superheated, and wet steam in the low-pressure range from 3 to 100 kPa. The proposed approach introduces a variable (local) gas constant that accounts the influence of pressure, temperature, and steam quality. Regression equations are obtained for the specific volume of steam as a function of pressure, temperature, and dryness degree. The results demonstrate that, within defined regions of superheat, the thermodynamic behavior of steam approaches to an ideal gas with a practically constant gas constant. For wet steam, simple relations based on steam quality are proposed. The derived approximation equations provide sufficient accuracy for engineering applications and can be effectively used for thermal and energy analysis of LP turbine stages operating under variable load conditions.

  • Open Access

    ENERGY CHARACTERISTICS OF FLOW STRUCTURAL ELEMENTS AT LOW-COST OPERATING MODES OF TURBINE STAGES WITH LONG BLADES

    by O. L. Shubenko, V. M. Goloschapov, O. V. Kotulska, T. M. Paramonova, P. O. Kotulskiy

    Low-cost operating modes of turbine stages with long blades span the range from idle operation to zero mass flow of the working medium, where a purely ventilatory regime is established. At idle, the flow remains close to jet-like behavior. A reduction in steam flow within the inter-blade gap generates a rotating vortex due to increased pressure in the central part of the blade channels. The working medium is eject into the inter-blade gap with high circumferential velocity, and the trailing edges of the rotor blades near the hub redirect the flow radially into the inter-stage gap or the outlet pipe, forming a hub-region flow separation. This study aims to analyze the energy characteristics of the flow structure in turbine stages with long blades based on experimental data, evaluating the energy supplied to the rotor and the associated thermal losses across the operating range . In low-flow regimes, the energy input from external sources to the rotor blades is determined using Euler’s equation, accounting for flow division into streamlets and integrating the energy supplied to each. This approach enables a one-dimensional representation of the three-dimensional viscous flow. The most significant aspect of low-flow regimes is the energy analysis of each flow component to assess energy losses driving the rotor and thermal losses affecting the thermal state of stage elements, particularly the rotor blades. Based on comprehensive analysis of existing experimental data from powerful turbine stages, a methodology has been developed incorporating regression equations for energy characteristics of each flow structure, considering blade length and flow capacity. The influence of blade length is quantified by the relative throughput of the stage, defined by the ratio of end-face areas and the sine relationship of flow exit angles from the guide vanes and rotor blades. Irreversible (thermal) losses of mechanical energy determine the heating level of the working medium at the measurement point. These losses allow for the estimation of medium heating within each flow structure, given known inlet or outlet temperatures.

  • Open Access

    APPROXIMATE RELATIONSHIPS FOR DETERMINING THE ENTHALPIES OF WATER AND STEAM IN THE CALCULATIONS OF HEAT EXCHANGER DEVICES OF STEAM TURBINE INSTALLATIONS (PART II – DETERMINATION OF THE ENTHALPY OF WATER STEAM)

    by Олександр Леонідович Шубенко, Volodymyr Goloshchapov, Ольга Валеріївна Котульська, Тетяна Миколаївна Парамонова, Володимир Миколайович Голощапов

    The conducted studies are the II part of a complex work on creating a methodological approach for determining the enthalpy of water and water vapor in the calculations of heat exchange equipment for operational control of the operating modes of large power steam turbines, when the use of tables of thermodynamic properties of working media in the "manual" mode is not successful. The current part II of the work, in contrast to part I, where the determination of the enthalpy of water is considered, is devoted to the determination of the enthalpy of water vapor. A methodological approach of obtaining approximating equations for determining enthalpy from the values of changing steam parameters is proposed, similar to what was done for water in рart I. In order to ensure the necessary approximation accuracy, the zone of the studied characteristics is divided by pressure into two regions - the vacuum region (1 kPa ≤ Р ≤ 100 kPa) and the overpressure region (0.1 MPa ≤ Р≤ 6 MPa), which in turn is divided into 3 regions (0.1 MPa ≤ Р ≤ 1 MPa, 1 MPa ≤ Р ≤ 3 MPa, 3 MPa ≤ Р ≤ 6 MPa). Since the effect of temperature in the area of the studied parameters is more significant than pressure, there was a need to introduce a significantly larger number of intervals in terms of temperature: 4 – in the vacuum area and15 – in the overpressure area. As a result, a system of approximating equations is proposed, which is characterized by sufficient accuracy in determining the enthalpy in the entire studied range of changes in the superheated steam parameters – pressure and temperature. To demonstrate the obtained results, an example of the application of the proposed methodology to the calculation of a specific heat exchange device is made in the work. The determination of the superheated steam consumption in the conditions of the thermal scheme of the T-250/300-240 heating turbine operated at the CHP, in relation to the PVТ-8 high-pressure heater for one of the operating modes, is given. As a result, it was found that the discrepancy between the value of the consumption of heating steam, determined according to the table values, and the consumption determined according to the obtained approximating dependencies, is 2.2 %, which is quite acceptable for practical needs in the operation of steam turbine plants.

  • Open Access

    APPROXIMATE RELATIONSHIPS FOR DETERMINING THE ENTHALPIES OF WATER AND STEAM IN THE CALCULATIONS OF HEAT EXCHANGER DEVICES OF STEAM TURBINE INSTALLATIONS (PART I – DETERMINATION OF THE ENTHALPY OF WATER)

    by Олександр Леонідович Шубенко, Volodymyr Goloshchapov, Ольга Валеріївна Котульська, Тетяна Миколаївна Парамонова, Володимир Миколайович Голощапов

    The work is devoted to the creation of a methodological approach for determining the thermodynamic properties of water and water vapor in the calculation of heat exchange processes for those cases when it is necessary to quickly control the operating modes of steam turbines of large power of thermal and nuclear power plants, but the use of existing tables of properties of working environments in the "manual" mode is not always suppose. In the presented part of the work the determination of the enthalpy of water is considered. Based on the analysis of the operating modes of heat exchangedevices of power units thermal and nuclear power plants of different capacities, the ranges of temperature and pressure changes of the working media during their calculations were determined. They are for water: at a pressure of 1 kPa–30 MPa, at a temperature of 1–300 °С, and for steam, respectively: 1 kPa–6 MPa, 7–450 °С. The analysis of tabular values of the working medium (water) showed that in order to present the enthalpy of water in an analytical form based on approximation equations with the required accuracy, it is advisable to consider their construction in two areas of change: in the area of vacuum (Р < 0.1 MPa) and in the area of excess pressure (0.1–30 MPa), which in turn are divided into 4 ranges. When thepressure changes, this is associated with an additional effect on the temperature enthalpy value, which complicates the choice of approximate dependencies for obtaining enthalpy from the parameters of the working environment while ensuring an acceptable ratio of calculated and tabular values for solving problems. By the authors a system of regression equations was obtained, allowing to calculate the enthalpy of water in a given range of pressures and temperatures with high accuracy. To determine the area in which the measured value is located, the authors proposed the use of Antoine's formula, in which the relationship between the pressure and temperature of the medium at the boundary line of the phase transition is established. To increase its accuracy, approximation equations for temperature corrections at different pressures are proposed, which ensure that the temperature deviates from the tabulated values of thermophysical properties there are no more than ±0.04 °С.


  • Open Access

    Increase of the Efficiency of Heat Supply Units of the CHP Plants Due to the Choice of Rational Heat Release Modes

    by Oleksandr L. Shubenko, Anatolii Pidhornyi Institute of Mechanical Engineering Problems of NAS of Ukraine, Svitlana V. Alyokhina, Volodymyr M. Holoshchapov, Olha A. Babenko, Olha V. Kotulska, University of Applied Sciences Technikum Wien

  • THERMAL STATE OF THE LOW-PRESSURE CYLINDER WORKING BLADES OF THE COGENERATION TURBINE T-250/300-240

    by Олександр Леонідович Шубенко, Volodymyr Goloshchapov, Ольга Валеріївна Котульська, Тетяна Миколаївна Парамонова, Daria Senetska, Володимир Миколайович Голощапов, Дар'я Олегівна Сенецька

    The important problem of researching the temperature state of the low-pressure cylinder of a powerful cogeneration turbine, which works, unlike condensing turbines, in conditions of significant changes in electrical and thermal load, is considered. This is since the low-pressure cylinder of the cogeneration turbines in the heating season operates at the low-flow rate modes due to the large selection of steam for heating. Such operating conditions are accompanied by the nucleation of vortex structures in the flow path, which leads to a significant increase in mechanical energy losses and, consequently, to an increase in the temperature of the elements of the flow path. The aim of the study is to determine the thermal state of the steam in a wide range of changes in the operation modes of the cogeneration turbine. The analysis of the results of experimental studies obtained on full-scale low-pressure cylinders of a powerful T-250/300-240 steam turbine by various authors in conditions of wide changes in operating parameters (the pressure in the condenser, the steam consumption in the flow path, the temperature of the lower heating selection) was performed. This made it possible to determine the temperature distribution along the height of the working blade of the last stage, which is of the greatest interest in the conditions of operation at the low-flow rate modes. The location of the minimum temperature is established, and a dependence is proposed for its determination at the exit from the working wheel of the stage, considering that the main generator of heat during steam heating is a rotating vortex in the rim clearance. It is shown that the limiting value of steam consumption through the last stage, which corresponds to the transition of the flow from the area of wet steam to the area of superheated steam, at a given temperature level in the lower heating selection, depends on the pressure in the condenser and can be determined as a function of these parameters. At the same time, with a decrease in the temperature in the lower heating selection and the pressure in the condenser, it will lead to the fact that the transition from the west steam to the superheated steam is observed at lower consumption. The increase of process moisture at the outlet of the working wheel occurs when the steam flow is greater than its limiting value.


  • Open Access

    POWER EXPENSES TO DRIVE A TURBINE STAGE UNDER LOW-FLOW MODES

    by Олександр Леонідович Шубенко, Svitlana Alyokhina, Volodymyr Goloshchapov, Ольга Валеріївна Котульська, Тетяна Миколаївна Парамонова, Daria Senetska, Світлана Вікторівна Альохіна, Володимир Миколайович Голощапов, Дар'я Олегівна Сенецька

    The task of determining the power consumption during the operation of the turbine stage in the low-cost mode is considered. To solve it, a theoreticalexperimental approach was used, based on the one-dimensional theory of the movement of a incompressible working medium and the results of an experimental study of a number of models of large fanning degrees, in which the working medium is air. When operating heating turbines, the lowpressure cylinders work in the area of low-cost modes up to 85 % of the time, both with a partially and completely closed rotary diaphragm of the regulating stage. When the volumetric flow rate of steam in the flow part of the low-pressure cylinder at low-flow modes is reduced, a sleeve separation of the flow develops and a vortex is formed in the inter-crown gap of the stage. The mode in which the power supplied to the impeller is spent on maintaining these currents corresponds to the "pure" ventilation mode. In contrast to the existing methods for determining the ventilation power losses in the stages of large fanning, the paper proposes a dependence based on the geometric configuration of the stages of the low-pressure cylinder of the heating turbines and their operating conditions. Taking into account the processes in the stage and the data obtained on the experimental stand, formulas were determined account the components of power losses - the function of the influence of the flow exit angles from the guide apparatus of the stage; influence of fanning l/Dmid; influence of the relative width of the working blade B/Dmid and the angle of inclination of the peripheral meridional circuit γm. The obtained dependences, which allow determining the coefficients of power consumption for the stage in the ventilation mode and the operation mode before idling, make it possible to calculate power consumption in the entire range of changes in low-flow modes. On the example of the last stage of the T-250/300-240 turbine, a comparison of the results of calculation studies according to the proposed dependence with the results obtained in real conditions of full-scale experiments was performed, which showed that their difference does not exceed 5 %.

  • Open Access

    Separation near the bushing of the flow in the outlet nozzle of the steam turbine at the low-flow rate modes

    by Oleksandr Shubenko, Svitlana Alyokhina, Volodymyr Goloshchapov, Olga Kotulska, Daria Senetska

    The paper considers the movement of steam flow from the working wheel of the last stage with a large fanning to the outlet nozzle of a steam turbine, considering the conditions for the formation of the separation near the bushing in a wide range of mode changes. An assessment was made of the initiation and development of the separation near the bushing in the space of the outlet nozzle of the steam turbine. To analyze the formation of the movement of the working medium in the free space of the outlet nozzle, an axisymmetric flow model is used, which is described by the equation of the hyperboloid of rotation.