Tetyana Vasilchenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tetyana Vasilchenko has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Oleksii Hrechanyі
Department of Metallurgical Equipment Zaporizhzhia National University Zaporizhzhia Ukraine
11 shared publications - Sergiy Sheyko
Zaporizhzhya National University
4 shared publications - Andrii Vlasov
Lviv State University of Physical Culture
3 shared publications - Volodymyr Tsyganov
National University “Zaporizhzhia Polytechnic
3 shared publications - Anastasiia Hrechana
Zaporizhzhya National University
2 shared publications Oleksii Hrechanyi
Запорізький національний університет
2 shared publications
Latest Publications
- Open Access
- 17 July 2026
- Published by Zaporizhzhia National University in Scientific Journal "Metallurgy"
- No. 1,p. 99-106
РОЗРОБКА МЕТОДИКИ ЛАБОРАТОРНИХ ДОСЛІДЖЕНЬ З ВИЗНАЧЕННЯ ЕНЕРГІЇ РУЙНУВАННЯ ІНТЕРМЕТАЛІДНИХ СПОЛУК ОТРИМАНИХ СПОСОБОМ ТЕРМОХІМІЧНОГО ПРЕСУВАННЯ
У роботі розглянуто актуальну науково-прикладну задачу визначення енергії руйнування інтерметалідних сполук, отриманих методом термохімічного пресування, що є необхідною умовою для обґрунтованого вибору типу подрібнюючого обладнання та оптимізації процесів їх дезінтеграції. Встановлено, що інтерметалідні матеріали характеризуються поєднанням високої твердості та крихкості, а також складною гетерогенною мікроструктурою, що суттєво ускладнює застосування традиційних методів оцінки їх руйнування. Проведено аналіз сучасних підходів до визначення енергії руйнування матеріалів, зокрема випробувань на ударний вигин за методом Шарпі, індентаційних методів та методів падаючого вантажу. Показано, що зазначені методики не повною мірою враховують специфіку структури та механізмів руйнування інтерметалідних сполук, отриманих термохімічним пресуванням, що обмежує їх практичне застосування. На основі проведеного аналізу запропоновано адаптовану методику лабораторних досліджень, яка реалізується із використанням маятникового копра та базується на принципі контрольованого ударного навантаження. Особливістю запропонованого підходу є відмова від виконання штучних надрізів у зразках, що обґрунтовано наявністю початкових структурних дефектів, сформованих у процесі синтезу. Розроблено аналітичні залежності для визначення енергії руйнування як різниці потенціальної енергії маятника до та після взаємодії зі зразком. Показано, що варіювання кута початкового відхилення маятника дозволяє моделювати різні режими ударного навантаження, характерні для роботи молоткових дробарок. Запропоновано критерій оцінки ступеня руйнування зразків, який базується на кількісній характеристиці утворених фрагментів і забезпечує узгодження лабораторних досліджень із реальними умовами подрібнення. Отримані результати створюють передумови для визначення питомої енергії дезінтеграції інтерметалідних матеріалів та можуть бути використані при проєктуванні, виборі та оптимізації параметрів дробильного обладнання.
- 17 July 2026
- Published by Zaporizhzhia National University in Scientific Journal "Metallurgy"
- No. 1,p. 99-106
Open AccessРОЗРОБКА МЕТОДИКИ ЛАБОРАТОРНИХ ДОСЛІДЖЕНЬ З ВИЗНАЧЕННЯ ЕНЕРГІЇ РУЙНУВАННЯ ІНТЕРМЕТАЛІДНИХ СПОЛУК ОТРИМАНИХ СПОСОБОМ ТЕРМОХІМІЧНОГО ПРЕСУВАННЯ
У роботі розглянуто актуальну науково-прикладну задачу визначення енергії руйнування інтерметалідних сполук, отриманих методом термохімічного пресування, що є необхідною умовою для обґрунтованого вибору типу подрібнюючого обладнання та оптимізації процесів їх дезінтеграції. Встановлено, що інтерметалідні матеріали характеризуються поєднанням високої твердості та крихкості, а також складною гетерогенною мікроструктурою, що суттєво ускладнює застосування традиційних методів оцінки їх руйнування. Проведено аналіз сучасних підходів до визначення енергії руйнування матеріалів, зокрема випробувань на ударний вигин за методом Шарпі, індентаційних методів та методів падаючого вантажу. Показано, що зазначені методики не повною мірою враховують специфіку структури та механізмів руйнування інтерметалідних сполук, отриманих термохімічним пресуванням, що обмежує їх практичне застосування. На основі проведеного аналізу запропоновано адаптовану методику лабораторних досліджень, яка реалізується із використанням маятникового копра та базується на принципі контрольованого ударного навантаження. Особливістю запропонованого підходу є відмова від виконання штучних надрізів у зразках, що обґрунтовано наявністю початкових структурних дефектів, сформованих у процесі синтезу. Розроблено аналітичні залежності для визначення енергії руйнування як різниці потенціальної енергії маятника до та після взаємодії зі зразком. Показано, що варіювання кута початкового відхилення маятника дозволяє моделювати різні режими ударного навантаження, характерні для роботи молоткових дробарок. Запропоновано критерій оцінки ступеня руйнування зразків, який базується на кількісній характеристиці утворених фрагментів і забезпечує узгодження лабораторних досліджень із реальними умовами подрібнення. Отримані результати створюють передумови для визначення питомої енергії дезінтеграції інтерметалідних матеріалів та можуть бути використані при проєктуванні, виборі та оптимізації параметрів дробильного обладнання.
- Open Access
- 30 June 2026
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 23 (2 (56))
A UNIFIED ANALYTICAL MODEL FOR DEFORMATION RESISTANCE OF METAL UNDER THERMOPLASTIC PROCESSING CONDITIONS
A unified analytical framework is developed to describe the deformation resistance of metals under thermoplastic processing conditions. The proposed approach is based on the Hansel-Spittel constitutive equation and establishes a direct relationship between yield stress and the key thermomechanical parameters of deformation, including strain, strain rate, and temperature. An analytical solution of the spatial plasticity problem is obtained using harmonic functions, enabling the determination of stress intensity at any point within the deformation zone. The formulation integrates the Huber-Mises plasticity criterion with frictional and geometric factors, resulting in a closed-form expression that links the local stress strain state to process parameters. The model accounts for non-uniform and multi-stage deformation characteristic of rolling and contact loading processes. Its applicability is demonstrated for thermoplastic loading of surface layers in tribological contacts, where deformation resistance plays a decisive role in wear and fatigue damage accumulation. The developed analytical model provides an efficient tool for predicting energy-force parameters and assessing surface layer behavior under complex thermomechanical loading. The proposed framework can be directly applied in engineering calculations, process optimization, and the design of metal forming and tribological systems.
- 30 June 2026
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 23 (2 (56))
Open AccessA UNIFIED ANALYTICAL MODEL FOR DEFORMATION RESISTANCE OF METAL UNDER THERMOPLASTIC PROCESSING CONDITIONS
A unified analytical framework is developed to describe the deformation resistance of metals under thermoplastic processing conditions. The proposed approach is based on the Hansel-Spittel constitutive equation and establishes a direct relationship between yield stress and the key thermomechanical parameters of deformation, including strain, strain rate, and temperature. An analytical solution of the spatial plasticity problem is obtained using harmonic functions, enabling the determination of stress intensity at any point within the deformation zone. The formulation integrates the Huber-Mises plasticity criterion with frictional and geometric factors, resulting in a closed-form expression that links the local stress strain state to process parameters. The model accounts for non-uniform and multi-stage deformation characteristic of rolling and contact loading processes. Its applicability is demonstrated for thermoplastic loading of surface layers in tribological contacts, where deformation resistance plays a decisive role in wear and fatigue damage accumulation. The developed analytical model provides an efficient tool for predicting energy-force parameters and assessing surface layer behavior under complex thermomechanical loading. The proposed framework can be directly applied in engineering calculations, process optimization, and the design of metal forming and tribological systems.
- Open Access
- 30 April 2026
- Published by National Metallurgical Academy of Ukraine in Modern Problems of Metalurgy
- No. 29,p. 127-139
ANALYSIS OF EQUIPMENT FOR OBTAINING A HIGH-STRENGTH HEAT-RESISTANT ALLOY WITH REDUCED DENSITY IN LABORATORY CONDITIONS
The work presents a systematic analysis of modern electrothermal equipment used to obtain high-strength heat-resistant nickel-based alloys with reduced density in research laboratory conditions. The relevance of the study is due to the needs of the aviation and energy industries for materials capable of operating at high temperatures, cyclic loads and in aggressive environments while simultaneously reducing the mass characteristics of parts. A comparative assessment of electric arc furnaces, vacuum arc and electroslag remelting installations, vacuum induction and electron beam systems has been carried out from the standpoint of metal purity, chemical composition stability, the possibility of precise alloying and suitability for use in laboratory conditions. It has been established that laboratory arc furnaces are appropriate for the initial development of alloy compositions, while electron beam installations are effective for obtaining ultrapure materials, but have significant economic limitations. It is shown that vacuum induction melting provides an optimal balance between the depth of refining, the accuracy of the introduction of alloying elements, the homogeneity of the structure and energy efficiency. Criteria for selecting laboratory equipment for the synthesis of new generation heat-resistant alloys are formulated, taking into account technological and infrastructural limitations. The results obtained can be used in the creation of mobile laboratory complexes for the research and development of new heat-resistant materials.
- 30 April 2026
- Published by National Metallurgical Academy of Ukraine in Modern Problems of Metalurgy
- No. 29,p. 127-139
Open AccessANALYSIS OF EQUIPMENT FOR OBTAINING A HIGH-STRENGTH HEAT-RESISTANT ALLOY WITH REDUCED DENSITY IN LABORATORY CONDITIONS
The work presents a systematic analysis of modern electrothermal equipment used to obtain high-strength heat-resistant nickel-based alloys with reduced density in research laboratory conditions. The relevance of the study is due to the needs of the aviation and energy industries for materials capable of operating at high temperatures, cyclic loads and in aggressive environments while simultaneously reducing the mass characteristics of parts. A comparative assessment of electric arc furnaces, vacuum arc and electroslag remelting installations, vacuum induction and electron beam systems has been carried out from the standpoint of metal purity, chemical composition stability, the possibility of precise alloying and suitability for use in laboratory conditions. It has been established that laboratory arc furnaces are appropriate for the initial development of alloy compositions, while electron beam installations are effective for obtaining ultrapure materials, but have significant economic limitations. It is shown that vacuum induction melting provides an optimal balance between the depth of refining, the accuracy of the introduction of alloying elements, the homogeneity of the structure and energy efficiency. Criteria for selecting laboratory equipment for the synthesis of new generation heat-resistant alloys are formulated, taking into account technological and infrastructural limitations. The results obtained can be used in the creation of mobile laboratory complexes for the research and development of new heat-resistant materials.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 21-24
АНАЛІЗ ОБЛАДНАННЯ ДЛЯ СТВОРЕННЯ В ЛАБОРАТОРНИХ УМОВАХ ЖАРОСТІЙКОГО СПЛАВУ ЗІ ЗНИЖЕНОЮ ЩІЛЬНІСТЮ
A systematic analysis of modern electrothermal equipment used to obtain high-strength heat-resistant nickel-based alloys with reduced density in laboratory conditions has been performed. The relevance of the study is due to the needs of the aviation and energy industries for materials capable of operating at high temperatures, cyclic loads and aggressive environments while simultaneously reducing the mass characteristics of structures. A comparative analysis of electric arc furnaces, vacuum arc and electroslag remelting, vacuum induction and electron beam systems has been performed. It has been established that vacuum induction melting provides an optimal balance between metal purity, alloying accuracy, structural homogeneity and energy efficiency. The prospects for creating mobile laboratory complexes for studying new generation heat-resistant alloys have been shown.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 21-24
АНАЛІЗ ОБЛАДНАННЯ ДЛЯ СТВОРЕННЯ В ЛАБОРАТОРНИХ УМОВАХ ЖАРОСТІЙКОГО СПЛАВУ ЗІ ЗНИЖЕНОЮ ЩІЛЬНІСТЮ
A systematic analysis of modern electrothermal equipment used to obtain high-strength heat-resistant nickel-based alloys with reduced density in laboratory conditions has been performed. The relevance of the study is due to the needs of the aviation and energy industries for materials capable of operating at high temperatures, cyclic loads and aggressive environments while simultaneously reducing the mass characteristics of structures. A comparative analysis of electric arc furnaces, vacuum arc and electroslag remelting, vacuum induction and electron beam systems has been performed. It has been established that vacuum induction melting provides an optimal balance between metal purity, alloying accuracy, structural homogeneity and energy efficiency. The prospects for creating mobile laboratory complexes for studying new generation heat-resistant alloys have been shown.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 10-14
ОБҐРУНТУВАННЯ МЕТОДИКИ ДОСЛІДЖЕННЯ ЕНЕРГІЇ ДЕЗІНТЕГРАЦІЇ ЗАГОТОВОК ІНТЕРМЕТАЛІДНИХ СПОЛУК ОТРИМАНИХ ТЕРМОХІМІЧНИМ ПРЕСУВАННЯМ
The paper considers the problem of increasing the efficiency of obtaining intermetallic compounds as promising materials for mechanical engineering. The features of their application, as well as the shortcomings of traditional manufacturing methods, are analyzed. The use of thermochemical pressing is proposed as an energy-efficient method of obtaining blanks of intermetallic compounds with predicted geometric parameters. The feasibility of determining the disintegration energy by the falling load method using a pendulum impact hammer is substantiated. The results obtained allow modeling grinding processes and reasonably selecting industrial equipment to achieve a given fraction of material.
- 26 April 2026
- Published by National Metallurgical Academy of Ukraine in International scientific and technical conference Information technologies in metallurgy and machine building
- p. 10-14
ОБҐРУНТУВАННЯ МЕТОДИКИ ДОСЛІДЖЕННЯ ЕНЕРГІЇ ДЕЗІНТЕГРАЦІЇ ЗАГОТОВОК ІНТЕРМЕТАЛІДНИХ СПОЛУК ОТРИМАНИХ ТЕРМОХІМІЧНИМ ПРЕСУВАННЯМ
The paper considers the problem of increasing the efficiency of obtaining intermetallic compounds as promising materials for mechanical engineering. The features of their application, as well as the shortcomings of traditional manufacturing methods, are analyzed. The use of thermochemical pressing is proposed as an energy-efficient method of obtaining blanks of intermetallic compounds with predicted geometric parameters. The feasibility of determining the disintegration energy by the falling load method using a pendulum impact hammer is substantiated. The results obtained allow modeling grinding processes and reasonably selecting industrial equipment to achieve a given fraction of material.
- Open Access
- 27 May 2025
- Published by Zaporizhzhia National University in Scientific Journal "Metallurgy"
- No. 1,p. 27-34
АНАЛІЗ МЕТОДІВ МОНТАЖУ ТА БАЗУВАННЯ ВУЗЛІВ ТЕХНОЛОГІЧНИХ ЛІНІЙ МЕТАЛУРГІЙНИХ ЦЕХІВ
Прокатне виробництво є завершальним етапом металургійного циклу, і якість готової продукції, що постачається споживачеві, безпосередньо залежить від злагодженої роботи всіх технологічних агрегатів. Високий рівень зношеності основних виробничих фондів металургійних підприємств зумовлює необхідність не лише їх оновлення, а й постійної модернізації застарілого обладнання. Оскільки оновлення здійснюється в умовах діючого виробництва, цей процес передбачає складні монтажні роботи з інтеграції нового або реконструйованого обладнання в уже функціонуючі виробничі лінії. Експлуатація механічного устаткування – це сукупність трьох взаємозалежних процесів: виконання технологічних операцій, зношування в процесі експлуатації та виконання ремонтних впливів по відновленню роботоздатності. Швидкість зношування машин і механізмів залежить як від інтенсивності технологічних впливів, так і від якості монтажних робіт, режимів змазування вузлів тертя, періодичності й повноти технічного обслуговування. Надійність машин залежить від якості конструкторських, технологічних і складальних робіт. Погрішності в розмірах, конфігурації, взаємному розташуванні деталей можуть привести до неприпустимого росту сил й аварійних відмов. Для металургійного встаткування такі погрішності часто проявляються при зборці, під якою розуміють сукупність операцій по з'єднанню деталей у виріб. Таким чином постає важливе питання встановлення оптимальних методів монтажу металургійного обладнання в умовах виробничого підприємства з огляду на можливість мінімізаціїї всіх можливих погрішностей складальних робіт. Відомі методи монтажу та вивірки базових деталей технологічного обладнання дещо застаріли та потребують постійного і безперервного удосконалення. Найбільш точним та швидким методом контролю точності складання та встановлення базових деталей є оптико-геодезичний, який дозволяє вивільнити до 20% робочого персоналу та одночасно зекономити до 30 % робочого часу в порівнянні зі струнним методом контролю складання вузлів металургійного обладнання.
- 27 May 2025
- Published by Zaporizhzhia National University in Scientific Journal "Metallurgy"
- No. 1,p. 27-34
Open AccessАНАЛІЗ МЕТОДІВ МОНТАЖУ ТА БАЗУВАННЯ ВУЗЛІВ ТЕХНОЛОГІЧНИХ ЛІНІЙ МЕТАЛУРГІЙНИХ ЦЕХІВ
Прокатне виробництво є завершальним етапом металургійного циклу, і якість готової продукції, що постачається споживачеві, безпосередньо залежить від злагодженої роботи всіх технологічних агрегатів. Високий рівень зношеності основних виробничих фондів металургійних підприємств зумовлює необхідність не лише їх оновлення, а й постійної модернізації застарілого обладнання. Оскільки оновлення здійснюється в умовах діючого виробництва, цей процес передбачає складні монтажні роботи з інтеграції нового або реконструйованого обладнання в уже функціонуючі виробничі лінії. Експлуатація механічного устаткування – це сукупність трьох взаємозалежних процесів: виконання технологічних операцій, зношування в процесі експлуатації та виконання ремонтних впливів по відновленню роботоздатності. Швидкість зношування машин і механізмів залежить як від інтенсивності технологічних впливів, так і від якості монтажних робіт, режимів змазування вузлів тертя, періодичності й повноти технічного обслуговування. Надійність машин залежить від якості конструкторських, технологічних і складальних робіт. Погрішності в розмірах, конфігурації, взаємному розташуванні деталей можуть привести до неприпустимого росту сил й аварійних відмов. Для металургійного встаткування такі погрішності часто проявляються при зборці, під якою розуміють сукупність операцій по з'єднанню деталей у виріб. Таким чином постає важливе питання встановлення оптимальних методів монтажу металургійного обладнання в умовах виробничого підприємства з огляду на можливість мінімізаціїї всіх можливих погрішностей складальних робіт. Відомі методи монтажу та вивірки базових деталей технологічного обладнання дещо застаріли та потребують постійного і безперервного удосконалення. Найбільш точним та швидким методом контролю точності складання та встановлення базових деталей є оптико-геодезичний, який дозволяє вивільнити до 20% робочого персоналу та одночасно зекономити до 30 % робочого часу в порівнянні зі струнним методом контролю складання вузлів металургійного обладнання.
- Open Access
- 30 September 2024
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 21 (3(49)) , 63-70
MODELING THE PLASTIC DEFORMATION STATE OF THE CONTACT SURFACE DURING FRICTION
The mechanics of contact destruction of compounds during friction under conditions of complex thermodynamic loading was researched. The possibility of a mathematical description of complex damage to friction units and wear intensity is shown, taking into account the peculiarities of the surface layer formation during contact. A method for calculating the surface strength and durability of tribo-compounds is presented. This allows us to relate the parameters of the stressed state of a point (friction coefficient, shape factor) with the thermomechanical parameters of the process. By assessing changes in the friction coefficient and shape parameters, it becomes possible to determine the yield stress and establish structural transformations corresponding to a given stress state.
- 30 September 2024
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 21 (3(49)) , 63-70
Open AccessMODELING THE PLASTIC DEFORMATION STATE OF THE CONTACT SURFACE DURING FRICTION
The mechanics of contact destruction of compounds during friction under conditions of complex thermodynamic loading was researched. The possibility of a mathematical description of complex damage to friction units and wear intensity is shown, taking into account the peculiarities of the surface layer formation during contact. A method for calculating the surface strength and durability of tribo-compounds is presented. This allows us to relate the parameters of the stressed state of a point (friction coefficient, shape factor) with the thermomechanical parameters of the process. By assessing changes in the friction coefficient and shape parameters, it becomes possible to determine the yield stress and establish structural transformations corresponding to a given stress state.
- Open Access
- 10 May 2024
- Published by Zaporizhzhia National University in Scientific Journal "Metallurgy"
- No. 2,p. 119-131
НОВИЙ НАПРЯМОК ВИРОБНИЦТВА ЗАГОТОВОК ДЛЯ МЕТАЛУРГІЇ І МАШИНОБУДУВАННЯ
Розроблено принципово новий спосіб отримання заготовок для сортопрокатного, трубного виробництва і машинобудування. Спосіб заснований на використанні процесу валкової розливки-прокатки, Розроблено принципово нову конструкцію установки розливки-прокатки, вона включає три валки-кристалізатори, які в сукупності з іншим оснащенням установки утворюють об'ємний міжвалковий простір, де створюється об'ємне масивне тіло заготовки, конструкція пристрою захищена патентом України на винахід. Спосіб і пристрій дозволяють отримувати суцільні та порожнисті заготовки, які можуть мати подвійне призначення. Конструктивні рішення базуються на апробованих авторських аналогах. Розробки пройшли первинну апробацію в умовах лабораторії кафедри металургійного обладнання Запорізького національного університету. Апробація мала експериментальний характер, основним завданням було випробування конструкції установки та нового способу. В результаті апробації встановлено технологічність способу та пристрою, підтверджено перспективність їх розвитку та застосування у промислових умовах. Підтверджено працездатність способу отримання заготовок та пристрою для його реалізації. Промислове виготовлення суцільних і порожнистих заготовок методом валкової розливки-прокатки дозволить поліпшити техніко-економічні показники металургійних і машинобудівних підприємств: скоротити металургійний цикл, знизити енергозатрати, зменшити металоємність обладнання, поліпшити екологічний стан. Результати розробок можуть бути використані підприємствами металургійного, машинобудівного комплексів, та оборонної галузі. Наявність заготовок нового типу дозволяє переглянути склад обладнання сортопрокатних та трубних цехів у напрямку скорочення його обсягу та енергоспоживання. У перспективі нові розробки стають основою створення нескінченної сортової прокатки.
- 10 May 2024
- Published by Zaporizhzhia National University in Scientific Journal "Metallurgy"
- No. 2,p. 119-131
Open AccessНОВИЙ НАПРЯМОК ВИРОБНИЦТВА ЗАГОТОВОК ДЛЯ МЕТАЛУРГІЇ І МАШИНОБУДУВАННЯ
Розроблено принципово новий спосіб отримання заготовок для сортопрокатного, трубного виробництва і машинобудування. Спосіб заснований на використанні процесу валкової розливки-прокатки, Розроблено принципово нову конструкцію установки розливки-прокатки, вона включає три валки-кристалізатори, які в сукупності з іншим оснащенням установки утворюють об'ємний міжвалковий простір, де створюється об'ємне масивне тіло заготовки, конструкція пристрою захищена патентом України на винахід. Спосіб і пристрій дозволяють отримувати суцільні та порожнисті заготовки, які можуть мати подвійне призначення. Конструктивні рішення базуються на апробованих авторських аналогах. Розробки пройшли первинну апробацію в умовах лабораторії кафедри металургійного обладнання Запорізького національного університету. Апробація мала експериментальний характер, основним завданням було випробування конструкції установки та нового способу. В результаті апробації встановлено технологічність способу та пристрою, підтверджено перспективність їх розвитку та застосування у промислових умовах. Підтверджено працездатність способу отримання заготовок та пристрою для його реалізації. Промислове виготовлення суцільних і порожнистих заготовок методом валкової розливки-прокатки дозволить поліпшити техніко-економічні показники металургійних і машинобудівних підприємств: скоротити металургійний цикл, знизити енергозатрати, зменшити металоємність обладнання, поліпшити екологічний стан. Результати розробок можуть бути використані підприємствами металургійного, машинобудівного комплексів, та оборонної галузі. Наявність заготовок нового типу дозволяє переглянути склад обладнання сортопрокатних та трубних цехів у напрямку скорочення його обсягу та енергоспоживання. У перспективі нові розробки стають основою створення нескінченної сортової прокатки.
- Open Access
- 1 December 2023
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 6 (4) , 508-511
Development of composite materials based on TiN–Mo cermets during thermochemical pressing
- 1 December 2023
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 6 (4) , 508-511
Open AccessDevelopment of composite materials based on TiN–Mo cermets during thermochemical pressing
- Open Access
- 18 March 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Science and innovation
- Vol. 19 (2) , 67-72
The Influence of Configuration Parameters of the Planetary Drive of Crank Presses on its Dynamic and Energy-Consumption Characteristics
Introduction. The planetary drive has been widely found in the activation systems of crank presses as it improves working conditions of friction units and reduces press metal consumption and energy consumption. Problem Statement. For studying the planetary motion of its main parts, it is advisable to consider its operation as four periods characterized by different patterns of changes in external loads and, consequently, different patterns of motion of core parts. The periods between switching the brakes when one link has not stopped, while other one starts moving is of the greatest interest. The problem of dynamic and energy-consumption parameters of the drive in transient conditions still remain a little open. Purpose. The purpose of this research is to qualitatively assess the influence of configuration parameters on the dynamics of the processes of switching and stopping the planetary drive. Material and Methods. The parameters of the experimental pilot plant, a model planetary drive with a nominal load of 400 kN, have been calculated. The minimum speed of the central gear has been estimated depending on the moments of inertia of the leading mass and the outer gear. The obtained dependences have been processed with the use of a standard mathematical apparatus. Results. It has been found that the energy-consumption and dynamic parameters of the drive are significantly influenced by such characteristics as moments of inertia and braking moments, while decreasing angular velocity of the drive flywheel does not depend on the moments of inertia of the stopped links. The rate of braking processes is determined by the elastic properties of the friction materials and the parameters of the brake springs, not by the parameters of compressed air outflow. Conclusions. The obtained analytical and graphical dependences have allowed not only qualitative, but also quantitative assessment of the influence of the parameters on the dynamics of processes. These recommendations can be used at the design stage, to select the optimal parameters of the drive with the predicted properties.
- 18 March 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Science and innovation
- Vol. 19 (2) , 67-72
Open AccessThe Influence of Configuration Parameters of the Planetary Drive of Crank Presses on its Dynamic and Energy-Consumption Characteristics
Introduction. The planetary drive has been widely found in the activation systems of crank presses as it improves working conditions of friction units and reduces press metal consumption and energy consumption. Problem Statement. For studying the planetary motion of its main parts, it is advisable to consider its operation as four periods characterized by different patterns of changes in external loads and, consequently, different patterns of motion of core parts. The periods between switching the brakes when one link has not stopped, while other one starts moving is of the greatest interest. The problem of dynamic and energy-consumption parameters of the drive in transient conditions still remain a little open. Purpose. The purpose of this research is to qualitatively assess the influence of configuration parameters on the dynamics of the processes of switching and stopping the planetary drive. Material and Methods. The parameters of the experimental pilot plant, a model planetary drive with a nominal load of 400 kN, have been calculated. The minimum speed of the central gear has been estimated depending on the moments of inertia of the leading mass and the outer gear. The obtained dependences have been processed with the use of a standard mathematical apparatus. Results. It has been found that the energy-consumption and dynamic parameters of the drive are significantly influenced by such characteristics as moments of inertia and braking moments, while decreasing angular velocity of the drive flywheel does not depend on the moments of inertia of the stopped links. The rate of braking processes is determined by the elastic properties of the friction materials and the parameters of the brake springs, not by the parameters of compressed air outflow. Conclusions. The obtained analytical and graphical dependences have allowed not only qualitative, but also quantitative assessment of the influence of the parameters on the dynamics of processes. These recommendations can be used at the design stage, to select the optimal parameters of the drive with the predicted properties.