Anastasiia Hrechana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Anastasiia Hrechana has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Sergiy Sheyko
Zaporizhzhya National University
3 shared publications - Oleksii Hrechanyі
Department of Metallurgical Equipment Zaporizhzhia National University Zaporizhzhia Ukraine
2 shared publications - Tetyana Vasilchenko
Zaporizhzhia National University
2 shared publications - Volodymyr Tsyganov
National University “Zaporizhzhia Polytechnic
2 shared publications Hennadii Snizhnoi
National University Zaporizhzhia Polytechnic
1 shared publication- Olexandr Shapurov
Zaporizhzhya National University
1 shared publication
Latest Publications
- Open Access
- 30 June 2026
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 23 (2 (56))
A UNIFIED ANALYTICAL MODEL FOR DEFORMATION RESISTANCE OF METAL UNDER THERMOPLASTIC PROCESSING CONDITIONS
A unified analytical framework is developed to describe the deformation resistance of metals under thermoplastic processing conditions. The proposed approach is based on the Hansel-Spittel constitutive equation and establishes a direct relationship between yield stress and the key thermomechanical parameters of deformation, including strain, strain rate, and temperature. An analytical solution of the spatial plasticity problem is obtained using harmonic functions, enabling the determination of stress intensity at any point within the deformation zone. The formulation integrates the Huber-Mises plasticity criterion with frictional and geometric factors, resulting in a closed-form expression that links the local stress strain state to process parameters. The model accounts for non-uniform and multi-stage deformation characteristic of rolling and contact loading processes. Its applicability is demonstrated for thermoplastic loading of surface layers in tribological contacts, where deformation resistance plays a decisive role in wear and fatigue damage accumulation. The developed analytical model provides an efficient tool for predicting energy-force parameters and assessing surface layer behavior under complex thermomechanical loading. The proposed framework can be directly applied in engineering calculations, process optimization, and the design of metal forming and tribological systems.
- 30 June 2026
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 23 (2 (56))
Open AccessA UNIFIED ANALYTICAL MODEL FOR DEFORMATION RESISTANCE OF METAL UNDER THERMOPLASTIC PROCESSING CONDITIONS
A unified analytical framework is developed to describe the deformation resistance of metals under thermoplastic processing conditions. The proposed approach is based on the Hansel-Spittel constitutive equation and establishes a direct relationship between yield stress and the key thermomechanical parameters of deformation, including strain, strain rate, and temperature. An analytical solution of the spatial plasticity problem is obtained using harmonic functions, enabling the determination of stress intensity at any point within the deformation zone. The formulation integrates the Huber-Mises plasticity criterion with frictional and geometric factors, resulting in a closed-form expression that links the local stress strain state to process parameters. The model accounts for non-uniform and multi-stage deformation characteristic of rolling and contact loading processes. Its applicability is demonstrated for thermoplastic loading of surface layers in tribological contacts, where deformation resistance plays a decisive role in wear and fatigue damage accumulation. The developed analytical model provides an efficient tool for predicting energy-force parameters and assessing surface layer behavior under complex thermomechanical loading. The proposed framework can be directly applied in engineering calculations, process optimization, and the design of metal forming and tribological systems.
- Open Access
- 24 June 2025
- Published by Oles Honchar Dnipropetrovsk National University in Challenges and Issues of Modern Science
- Vol. 4 (1) , 48-54
Austenite Stability and Wear Resistance of High-Manganese Steels
Purpose. Classification of wear-resistant components used in metallurgical equipment by category and optimization of high-manganese steel selection. Design / Method / Approach. The study was conducted on steels produced in induction furnaces with water quenching at 1050 °C. Samples of 5 × 3 × 3 mm³ were subjected to slow plastic deformation by compression. The degree of deformation was determined by the ratio of the sample thickness before and after deformation. The magnetic state was evaluated by the magnetometric method using a Faraday balance. Findings. At 20–30% deformation, 110Mn8 formed 2.787 vol.% α′-martensite, 110Mn10 – 0.263 vol.%, 110Mn13 – 0.107 vol.%, and 110Mn18 – 0.006 vol.%. Steels 110Mn8 and 110Mn10 exhibit low austenite stability, while 110Mn13 and 110Mn18 are metastable. A classification of parts by operating conditions was proposed: I – especially critical purpose (110Mn13, 110Mn18), II – critical purpose (110Mn10), III – general purpose (110Mn8). Theoretical Implications. The study enhances understanding of the role of martensitic transformation in the wear resistance of high-manganese steels and clarifies the relationship between chemical composition and austenite stability. Practical Implications. The classification enables optimized steel selection for parts based on operating conditions, reducing material costs and improving equipment reliability. Originality / Value. This is the first study to propose a classification of metallurgical equipment parts by categories, considering austenite stability, facilitating rational material selection. Research Limitations / Future Research. Future research should explore the effects of additional alloying elements and compare them with other deformation types. Article Type. Empirical. PURL: https://purl.org/cims/4.286
- 24 June 2025
- Published by Oles Honchar Dnipropetrovsk National University in Challenges and Issues of Modern Science
- Vol. 4 (1) , 48-54
Open AccessAustenite Stability and Wear Resistance of High-Manganese Steels
Purpose. Classification of wear-resistant components used in metallurgical equipment by category and optimization of high-manganese steel selection. Design / Method / Approach. The study was conducted on steels produced in induction furnaces with water quenching at 1050 °C. Samples of 5 × 3 × 3 mm³ were subjected to slow plastic deformation by compression. The degree of deformation was determined by the ratio of the sample thickness before and after deformation. The magnetic state was evaluated by the magnetometric method using a Faraday balance. Findings. At 20–30% deformation, 110Mn8 formed 2.787 vol.% α′-martensite, 110Mn10 – 0.263 vol.%, 110Mn13 – 0.107 vol.%, and 110Mn18 – 0.006 vol.%. Steels 110Mn8 and 110Mn10 exhibit low austenite stability, while 110Mn13 and 110Mn18 are metastable. A classification of parts by operating conditions was proposed: I – especially critical purpose (110Mn13, 110Mn18), II – critical purpose (110Mn10), III – general purpose (110Mn8). Theoretical Implications. The study enhances understanding of the role of martensitic transformation in the wear resistance of high-manganese steels and clarifies the relationship between chemical composition and austenite stability. Practical Implications. The classification enables optimized steel selection for parts based on operating conditions, reducing material costs and improving equipment reliability. Originality / Value. This is the first study to propose a classification of metallurgical equipment parts by categories, considering austenite stability, facilitating rational material selection. Research Limitations / Future Research. Future research should explore the effects of additional alloying elements and compare them with other deformation types. Article Type. Empirical. PURL: https://purl.org/cims/4.286
- Open Access
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Determination of the optimal temperature regime of plastic deformation of micro alloyed automobile wheel steels
Determination of the optimal temperature regime of plastic deformation of micro alloyed automobile wheel steels
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessDetermination of the optimal temperature regime of plastic deformation of micro alloyed automobile wheel steels
Determination of the optimal temperature regime of plastic deformation of micro alloyed automobile wheel steels