Dilek Arslan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dilek Arslan has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Recep Onur Uzun
Manisa Celal Bayar University
3 shared publications - Safiye İpEk Ayvaz
MANİSA CELÂL BAYAR ÜNİVERSİTESİ, TURGUTLU MESLEK YÜKSEKOKULU
1 shared publication - Selda Akgün
MANİSA CELÂL BAYAR ÜNİVERSİTESİ, HASAN FERDİ TURGUTLU TEKNOLOJİ FAKÜLTESİ, MAKİNE MÜHENDİSLİĞİ BÖLÜMÜ
1 shared publication
Latest Publications
- Open Access
- 20 August 2024
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 8 (2) , 76-83
Influences of post-weld artificial aging on microstructural and tensile properties of friction stir-welded Al-Zn-Mg-Si-Cu aluminum alloy joints
In this study, the effect of heat treatment on the mechanical and microstructural properties of welded joints after friction stir welding of age-hardenable Al-Zn-Mg-Si-Cu wrought aluminum alloy plates was investigated. For this purpose, some of the samples welded using FSW technique with a rotational speed of 1250 rpm and a traverse speed of 40 mm·min-1 were subjected to annealing and some to artificial aging heat treatment at different temperatures and times. In FSWed artificial aged samples where AlFeSi precipitate formations were detected, hardness and strength increase were realized with grain-boundary strengthening and Orowan hardening mechanisms. The lowest ultimate tensile strength was 156.3 N·mm-2 in the annealed sample, while the highest ultimate tensile strength was 210.8 N·mm-2 in the sample artificially aged at 190 °C for 2 hours. Fractographic examination revealed that ductile fracture occurred in all specimens.
- 20 August 2024
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 8 (2) , 76-83
Open AccessInfluences of post-weld artificial aging on microstructural and tensile properties of friction stir-welded Al-Zn-Mg-Si-Cu aluminum alloy joints
In this study, the effect of heat treatment on the mechanical and microstructural properties of welded joints after friction stir welding of age-hardenable Al-Zn-Mg-Si-Cu wrought aluminum alloy plates was investigated. For this purpose, some of the samples welded using FSW technique with a rotational speed of 1250 rpm and a traverse speed of 40 mm·min-1 were subjected to annealing and some to artificial aging heat treatment at different temperatures and times. In FSWed artificial aged samples where AlFeSi precipitate formations were detected, hardness and strength increase were realized with grain-boundary strengthening and Orowan hardening mechanisms. The lowest ultimate tensile strength was 156.3 N·mm-2 in the annealed sample, while the highest ultimate tensile strength was 210.8 N·mm-2 in the sample artificially aged at 190 °C for 2 hours. Fractographic examination revealed that ductile fracture occurred in all specimens.
- 28 June 2021
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 17 (2) , 181-191
Adhesive Behavior of the Pack-Borided AISI 304L Steel with Microwave Hybrid Heating
Pack-boriding was applied to AISI 304L stainless steel material at temperatures of 850, 900 and 950 °C for 2, 4 and 6 hours with microwave hybrid heating method. The morphology of the boride layer formed on the surface of the samples was examined by optical microscope, and the phases formed in the layer were determined by XRD. The analysis of the adhesive strength of the boride layer to the substrate material was carried out by the Daimler-Benz Rockwell-C adhesion test. The tests were repeated at least 3 times for each of the pack-borided samples at all process temperatures and times. After the adhesion tests, macro and SEM images of indentation traces were taken. By analysing the indentation craters, it has been determined whether the damages are acceptable or not with reference to the VDI 3198 standard. The indentation craters formed on the pack-borided AISI 304L stainless steel sample surfaces at 850 °C with microwave hybrid heating method in all process times, for 2 and 4 hours at 900 °C, and 2 hours at 950 °C have the best adhesion quality in the HF1 category of the VDI 3198 norm.
- 28 June 2021
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 17 (2) , 181-191
Adhesive Behavior of the Pack-Borided AISI 304L Steel with Microwave Hybrid Heating
Pack-boriding was applied to AISI 304L stainless steel material at temperatures of 850, 900 and 950 °C for 2, 4 and 6 hours with microwave hybrid heating method. The morphology of the boride layer formed on the surface of the samples was examined by optical microscope, and the phases formed in the layer were determined by XRD. The analysis of the adhesive strength of the boride layer to the substrate material was carried out by the Daimler-Benz Rockwell-C adhesion test. The tests were repeated at least 3 times for each of the pack-borided samples at all process temperatures and times. After the adhesion tests, macro and SEM images of indentation traces were taken. By analysing the indentation craters, it has been determined whether the damages are acceptable or not with reference to the VDI 3198 standard. The indentation craters formed on the pack-borided AISI 304L stainless steel sample surfaces at 850 °C with microwave hybrid heating method in all process times, for 2 and 4 hours at 900 °C, and 2 hours at 950 °C have the best adhesion quality in the HF1 category of the VDI 3198 norm.
- Open Access
- 15 April 2021
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 5 (1) , 61-71
Mechanical characterization of pack-boronized AISI 4140 and AISI H13 steels
Wear losses have a great importance in the world machinery industry. They cause billions of dollars in financial losses every year. Studies on surface treatments are increasing day by day in order to minimize the wear losses of materials. In this study, the pack boronizing process was applied to AISI 4140 and AISI H13 steels, which are frequently used in the manufacturing and molding industry, by using Ekabor II powder at 900 °C and 950 °C for 4 and 6 hours. Microstructural examinations of the samples subjected to metallographic processes were carried out. Afterwards, microhardness measurements were performed by applying 50 gf load for 10 seconds. Wear tests were carried out using pin-on-disk tribotests in a dry environment under 2 N and 5 N loads on the CSM Tribometer device. Wear losses were measured as volumetric loss. Thanks to the boronizing process, surface quality, surface hardness, and wear resistance of both steel materials were increased at a high rate.
- 15 April 2021
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 5 (1) , 61-71
Open AccessMechanical characterization of pack-boronized AISI 4140 and AISI H13 steels
Wear losses have a great importance in the world machinery industry. They cause billions of dollars in financial losses every year. Studies on surface treatments are increasing day by day in order to minimize the wear losses of materials. In this study, the pack boronizing process was applied to AISI 4140 and AISI H13 steels, which are frequently used in the manufacturing and molding industry, by using Ekabor II powder at 900 °C and 950 °C for 4 and 6 hours. Microstructural examinations of the samples subjected to metallographic processes were carried out. Afterwards, microhardness measurements were performed by applying 50 gf load for 10 seconds. Wear tests were carried out using pin-on-disk tribotests in a dry environment under 2 N and 5 N loads on the CSM Tribometer device. Wear losses were measured as volumetric loss. Thanks to the boronizing process, surface quality, surface hardness, and wear resistance of both steel materials were increased at a high rate.
- Open Access
- 3 March 2021
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 24 (1) , 34-41
RETROGRESYON VE YENİDEN YAŞLANDIRMA İŞLEMİ UYGULANMIŞ 7075 ALÜMİNYUM ALAŞIMININ SERTLİK DAVRANIŞI
Metallerin mekanik özellikleri ısıl işlem uygulanması ile artırılabilmektedir. Alüminyum ve alaşımlarının sertlik dayanımlarını arttırabilmek için yaşlandırma işlemi uygulanabilmektedir. Bu çalışmada da 7075 alüminyum alaşımına retrogresyon ve yeniden yaşlandırma işlemi uygulanmıştır. Uygun çözeltiye alma ve suni olarak yaşlandırma işlemi olan T6 ısıl işleminin gerçekleştirildiğinden emin olmak için öncelikle 7075 alüminyum alaşım 480˚C’de 2 saat çözeltide bekletilerek ardından soğutulup, oda sıcaklığında doğal olarak yaşlandırılmıştır. T6 ısıl işlemini ve sonrasında T6 işleminden daha yüksek 150˚C -170˚C -190˚C sıcaklıkları arasında 60 dakika, 180 dakika ve 300 dakika sürelerde yaşlandırma uygulanmıştır. Yaşlandırma sürecinde yeniden çözeltiye alma süresi ve sıcaklıklarını değiştirerek bu değerlerin AA7075 alüminyum alaşımının sertlik değerlerine etkisi araştırılmıştır. Çalışma sonuçları, çözeltiye alma sıcaklığının ve süresinin alüminyum alaşımının sertlik değerinde artış sağladığını göstermiştir. Isıl işlemin sıcaklık ve bekletme süresi, alüminyum alaşımlarının mikroyapısında meydana getirdiği değişikliklerden dolayı alaşımların sertlik değerlerini etkilemektedir.
- 3 March 2021
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 24 (1) , 34-41
Open AccessRETROGRESYON VE YENİDEN YAŞLANDIRMA İŞLEMİ UYGULANMIŞ 7075 ALÜMİNYUM ALAŞIMININ SERTLİK DAVRANIŞI
Metallerin mekanik özellikleri ısıl işlem uygulanması ile artırılabilmektedir. Alüminyum ve alaşımlarının sertlik dayanımlarını arttırabilmek için yaşlandırma işlemi uygulanabilmektedir. Bu çalışmada da 7075 alüminyum alaşımına retrogresyon ve yeniden yaşlandırma işlemi uygulanmıştır. Uygun çözeltiye alma ve suni olarak yaşlandırma işlemi olan T6 ısıl işleminin gerçekleştirildiğinden emin olmak için öncelikle 7075 alüminyum alaşım 480˚C’de 2 saat çözeltide bekletilerek ardından soğutulup, oda sıcaklığında doğal olarak yaşlandırılmıştır. T6 ısıl işlemini ve sonrasında T6 işleminden daha yüksek 150˚C -170˚C -190˚C sıcaklıkları arasında 60 dakika, 180 dakika ve 300 dakika sürelerde yaşlandırma uygulanmıştır. Yaşlandırma sürecinde yeniden çözeltiye alma süresi ve sıcaklıklarını değiştirerek bu değerlerin AA7075 alüminyum alaşımının sertlik değerlerine etkisi araştırılmıştır. Çalışma sonuçları, çözeltiye alma sıcaklığının ve süresinin alüminyum alaşımının sertlik değerinde artış sağladığını göstermiştir. Isıl işlemin sıcaklık ve bekletme süresi, alüminyum alaşımlarının mikroyapısında meydana getirdiği değişikliklerden dolayı alaşımların sertlik değerlerini etkilemektedir.
- 1 March 2021
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 11 (1) , 490-499
Microwave Boriding to Improve the Corrosion Resistance of AISI 304L Austenitic Stainless Steel
In this study, the corrosion behaviors of AISI 304L austenitic stainless steel samples were subjected to pack-boriding at 850, 900 and 950 °C process temperatures for 2, 4 and 6 hours with microwave hybrid heating, and examined. Boride layers were characterized by optical microscope and XRD. As a result of XRD analyses, the presence of FeB, Fe2B, Cr2B and Ni2B compounds in the boride layers were determined formed on the sample surfaces. As an alternative to conventional heating, AISI 304L austenitic stainless steel samples subjected to pack-boriding with microwave hybrid heating, as a result of the corrosion tests carried out during the 3rd, 7th and 10th days in 2% V/V (for volume per volume) HNO3 acid solution, the corrosion resistance of the AISI 304L austenitic stainless steel samples as loss in mass increased with the increase in the temperature and duration of the boriding process and the corrosion resistance increased 95 times compared to the untreated AISI 304L stainless steel samples.
- 1 March 2021
- Published by Igdir University in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 11 (1) , 490-499
Microwave Boriding to Improve the Corrosion Resistance of AISI 304L Austenitic Stainless Steel
In this study, the corrosion behaviors of AISI 304L austenitic stainless steel samples were subjected to pack-boriding at 850, 900 and 950 °C process temperatures for 2, 4 and 6 hours with microwave hybrid heating, and examined. Boride layers were characterized by optical microscope and XRD. As a result of XRD analyses, the presence of FeB, Fe2B, Cr2B and Ni2B compounds in the boride layers were determined formed on the sample surfaces. As an alternative to conventional heating, AISI 304L austenitic stainless steel samples subjected to pack-boriding with microwave hybrid heating, as a result of the corrosion tests carried out during the 3rd, 7th and 10th days in 2% V/V (for volume per volume) HNO3 acid solution, the corrosion resistance of the AISI 304L austenitic stainless steel samples as loss in mass increased with the increase in the temperature and duration of the boriding process and the corrosion resistance increased 95 times compared to the untreated AISI 304L stainless steel samples.