Nureddin Dinler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nureddin Dinler has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Nuri Yucel
Gazi Üniversitesi
5 shared publications - Salih Karaaslan
Gazi Üniversitesi
5 shared publications - Fatih Aktas
Gazi University
4 shared publications - Gonca Kethudaoglu
Amasya Üniversitesi
2 shared publications Nuri Yucel
Engineering Faculty, Department of Mechanical Engineering, Gazi University, Maltepe, Ankara, Turkey
2 shared publications- Ahmet Turker
Department of Mechanical Engineering, Faculty of Engineering, Gazi University, Maltepe, Ankara, Turkey
1 shared publication
Latest Publications
- Open Access
- 3 March 2026
- Published by Elsevier in SSRN Electronic Journal
Aerodynamic Effects of Distributed Propulsion viaBEM-FVM Coupling
Distributed propulsion is a promising concept for enhancing aerodynamic efficiency and energy performance in modern aircraft configurations. This study presents a Blade Element Momentum (BEM) model integrated into an open-source finite volume method (FVM) solver to evaluate rotor–wing aerodynamic interactions. The developed BEM–FVM coupling framework is validated against NASA ROBIN experimental data, demonstrating thrust prediction errors below 5\% under moderate cyclic inputs. It is observed that as cyclic loading increases and rotor inflow becomes strongly non-uniform, the deviation between numerical predictions and experimental data grows due to the inherent limitations of single-plane actuator modeling. The study further highlights the coupling characteristics between actuator source terms and mesh resolution, emphasizing that improper mesh–source consistency may lead to divergence. Following validation, thrust-equivalent distributed propulsion configurations are analyzed on a generic wing model. The results indicate that distributed propulsion improves the lift-to-drag ratio by up to 3.4\% while reducing power requirement by up to 9\% compared to a single-rotor configuration. The proposed framework provides a computationally efficient tool suitable for preliminary rotor placement and sizing studies prior to high-fidelity simulations.
- 3 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAerodynamic Effects of Distributed Propulsion viaBEM-FVM Coupling
Distributed propulsion is a promising concept for enhancing aerodynamic efficiency and energy performance in modern aircraft configurations. This study presents a Blade Element Momentum (BEM) model integrated into an open-source finite volume method (FVM) solver to evaluate rotor–wing aerodynamic interactions. The developed BEM–FVM coupling framework is validated against NASA ROBIN experimental data, demonstrating thrust prediction errors below 5\% under moderate cyclic inputs. It is observed that as cyclic loading increases and rotor inflow becomes strongly non-uniform, the deviation between numerical predictions and experimental data grows due to the inherent limitations of single-plane actuator modeling. The study further highlights the coupling characteristics between actuator source terms and mesh resolution, emphasizing that improper mesh–source consistency may lead to divergence. Following validation, thrust-equivalent distributed propulsion configurations are analyzed on a generic wing model. The results indicate that distributed propulsion improves the lift-to-drag ratio by up to 3.4\% while reducing power requirement by up to 9\% compared to a single-rotor configuration. The proposed framework provides a computationally efficient tool suitable for preliminary rotor placement and sizing studies prior to high-fidelity simulations.
- Open Access
- 4 December 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (6) , 1681-1690
İki Farklı Desenli Lastik İçin Suda Kızaklamanın İncelenmesi
Bir taşıt için önemli güvenlik unsurlarından birisi lastiklerdir. Taşıtın yükünü ve ağırlığına taşırken, yeterli tahrik ve frenleme kuvveti sunmalı, yeterli yönlendirme ve doğrultu kararlılığı sağlarken taşıtın konforunu da korumalıdır. Lastiklerde önemli konulardan birisi de suda kızaklama (aquaplanning) problemidir. Bu çalışmada asimetrik desenli ve yönlü desenli iki lastik seti için suda kızaklama deneyleri yapılmıştır. Lastik derinliklerinin suda kızaklamaya olan etkileri incelenmiştir. Diş derinliğinin yüksek olduğu durumda yönlü lastiklerin asimetrik desenli lastiklere göre yaklaşık %10 daha yüksek hızda suda kızaklamaya girdiği görülmüştür. Diş derinliklerinin azaltılmasından sonra ise suda kızaklama hızının düştüğü görülmüştür. Yani, daha düşük hızlarda suda kızaklama oluşmuştur. Diş derinliği azalmış olan iki lastik de birbirine yakın hızlarda suda kızaklamaya girmişlerdir.
- 4 December 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (6) , 1681-1690
Open Accessİki Farklı Desenli Lastik İçin Suda Kızaklamanın İncelenmesi
Bir taşıt için önemli güvenlik unsurlarından birisi lastiklerdir. Taşıtın yükünü ve ağırlığına taşırken, yeterli tahrik ve frenleme kuvveti sunmalı, yeterli yönlendirme ve doğrultu kararlılığı sağlarken taşıtın konforunu da korumalıdır. Lastiklerde önemli konulardan birisi de suda kızaklama (aquaplanning) problemidir. Bu çalışmada asimetrik desenli ve yönlü desenli iki lastik seti için suda kızaklama deneyleri yapılmıştır. Lastik derinliklerinin suda kızaklamaya olan etkileri incelenmiştir. Diş derinliğinin yüksek olduğu durumda yönlü lastiklerin asimetrik desenli lastiklere göre yaklaşık %10 daha yüksek hızda suda kızaklamaya girdiği görülmüştür. Diş derinliklerinin azaltılmasından sonra ise suda kızaklama hızının düştüğü görülmüştür. Yani, daha düşük hızlarda suda kızaklama oluşmuştur. Diş derinliği azalmış olan iki lastik de birbirine yakın hızlarda suda kızaklamaya girmişlerdir.
- 30 September 2025
- Published by Springer Nature in Sādhanā
- Vol. 50 (4) , 1-15
Effects of the jet fans on different fire locations in a curved road tunnel
- 30 September 2025
- Published by Springer Nature in Sādhanā
- Vol. 50 (4) , 1-15
Effects of the jet fans on different fire locations in a curved road tunnel
- 1 January 2025
- Published by Begell House Inc. Publishers in Heat Transfer Research
- Vol. 56 (5) , 1-15
OPTIMIZING AIRCRAFT AVIONIC THERMAL MANAGEMENT: A COMPREHENSIVE STUDY ON THE IMPACT OF GEOMETRIES AND ENVIRONMENTAL FACTORS
Thermal management in aircraft is crucial to maintain thermal balance, ensure the stable operation of avionic systems and other critical components. Avionic temperatures are influenced by external factors like ambient temperature, mass flow rate, thermal load, compartment temperature, and air inlet/outlet design. The aim is to analyze temperature effects under various conditions, including cockpit temperature (297 to 303 K), air flow rates (0.10 to 0.25 kg/s), system placements, outlet designs, and equipment thermal loads (original values and ± 10 W). Three configurations were created for analysis, revealing that a +10-W thermal load increases average avionic temperatures by 3.1 K, while a -10-W load decreases them by 3 K. Increased ventilation flow decreases avionic temperatures by 13.8 K, while higher ventilation air temperature increases them by 4.7 K. These trends demonstrate a stable pattern in temperature changes with varying thermal load, mass flow rate, and temperature alterations. Analyzing two outlets at different locations with the same area shows an average avionic temperature change of 2 K, while altering the system layout results in an average temperature difference of 7.2 K. System layout modifications may cause up to a 20 K temperature change for some equipment, leaving others unaffected. These findings highlight the impact of geometries and environmental factors on avionic equipment. Thermal load, ventilation flow, temperature changes, and system placement affect avionic temperatures differently, providing valuable insights for system optimization and avionic equipment placement.
- 1 January 2025
- Published by Begell House Inc. Publishers in Heat Transfer Research
- Vol. 56 (5) , 1-15
OPTIMIZING AIRCRAFT AVIONIC THERMAL MANAGEMENT: A COMPREHENSIVE STUDY ON THE IMPACT OF GEOMETRIES AND ENVIRONMENTAL FACTORS
Thermal management in aircraft is crucial to maintain thermal balance, ensure the stable operation of avionic systems and other critical components. Avionic temperatures are influenced by external factors like ambient temperature, mass flow rate, thermal load, compartment temperature, and air inlet/outlet design. The aim is to analyze temperature effects under various conditions, including cockpit temperature (297 to 303 K), air flow rates (0.10 to 0.25 kg/s), system placements, outlet designs, and equipment thermal loads (original values and ± 10 W). Three configurations were created for analysis, revealing that a +10-W thermal load increases average avionic temperatures by 3.1 K, while a -10-W load decreases them by 3 K. Increased ventilation flow decreases avionic temperatures by 13.8 K, while higher ventilation air temperature increases them by 4.7 K. These trends demonstrate a stable pattern in temperature changes with varying thermal load, mass flow rate, and temperature alterations. Analyzing two outlets at different locations with the same area shows an average avionic temperature change of 2 K, while altering the system layout results in an average temperature difference of 7.2 K. System layout modifications may cause up to a 20 K temperature change for some equipment, leaving others unaffected. These findings highlight the impact of geometries and environmental factors on avionic equipment. Thermal load, ventilation flow, temperature changes, and system placement affect avionic temperatures differently, providing valuable insights for system optimization and avionic equipment placement.
- Open Access
- 31 March 2024
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 8 (1) , 142-149
0/1 and 3 - dimensional cold flow analysis of a diesel engine: A case study
Gas motion in the engine cylinder plays a critical role in diesel engines' air-fuel mixing and combustion processes. Moreover, it influences the engine's performance, emissions, and heat transfer. The intake air motion regulates the main phases of the flow in the cylinder, which is characterized by swirl, squish, and turbulence. Inducing swirl and tumble in the intake process provides high turbulence levels at ignition, resulting in more effective flame speeds and better combustion for lean air-fuel ratios or with EGR. Computational fluid dynamics (CFD) software is used to enhance in-cylinder flow characteristics. In this study, a cold flow simulation of a naturally aspirated, direct injection diesel engine was conducted with different piston bowls using AVL Fire M R2022.2. Swirl, tumble, and TKE parameters were investigated to make a detailed analysis of the in-cylinder flow for the relevant engine. Contrary to the expectation, the swirl ratio for the Piston B configuration is less than that for the original piston configuration. It causes a decrement of swirl ratio compared to the initial piston geometry and the maximum decrement is about 19%. In both cases, the second peak of TKE corresponding to the reverse-squish is around at the -30 CA and the difference between the curves is about ±8%.
- 31 March 2024
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 8 (1) , 142-149
Open Access0/1 and 3 - dimensional cold flow analysis of a diesel engine: A case study
Gas motion in the engine cylinder plays a critical role in diesel engines' air-fuel mixing and combustion processes. Moreover, it influences the engine's performance, emissions, and heat transfer. The intake air motion regulates the main phases of the flow in the cylinder, which is characterized by swirl, squish, and turbulence. Inducing swirl and tumble in the intake process provides high turbulence levels at ignition, resulting in more effective flame speeds and better combustion for lean air-fuel ratios or with EGR. Computational fluid dynamics (CFD) software is used to enhance in-cylinder flow characteristics. In this study, a cold flow simulation of a naturally aspirated, direct injection diesel engine was conducted with different piston bowls using AVL Fire M R2022.2. Swirl, tumble, and TKE parameters were investigated to make a detailed analysis of the in-cylinder flow for the relevant engine. Contrary to the expectation, the swirl ratio for the Piston B configuration is less than that for the original piston configuration. It causes a decrement of swirl ratio compared to the initial piston geometry and the maximum decrement is about 19%. In both cases, the second peak of TKE corresponding to the reverse-squish is around at the -30 CA and the difference between the curves is about ±8%.
- 22 September 2023
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 8 (3) , 535-556
Investigation of conversion of a diesel engine to homogeneous charge compression ignition engine using n-heptane: A zero-dimensional modeling
Numerical methods are commonly used for analyzing combustion characteristics. Besides, they provide an opportunity to predict emissions of an engine. In this paper, the conversion of a single-cylinder diesel engine to HCCI combustion model is investigated with AVL Boost v2021R2. The model was used to simulate the power, emission, bsfc value. In-cylinder pressure results also are obtained from the model. Verification of the model is conducted with experimental data from the literature. The differentiation between the numerical and experimental results remained below 8.9% for the power, below 6.62% for bsfc. In addition to this, the model gave maximum pressure values with an accuracy of ± 1%, and maximum HRR values with an accuracy of ± 2%. Maximum HRR values and in-cylinder pressure curves for 1200-2400 rpm were obtained with acceptable accuracy. Besides, the operating range of an HCCI engine fueled with n-heptane was investigated using a zero-dimensional single-zone model with reduced fuel chemistry. The compression ratio and inlet air temperature effect on HCCI combustion were analyzed. The increasing the air inlet temperature to 40oC from 20oC, increases the lowest air-fuel ratio about 6.6% which the engine can operate without entering the knock zone, at 17.5 CR at 1200rpm.
- 22 September 2023
- Published by Türkiye Enerji Stratejileri ve Politikalari Araştirma Merkezi (TESPAM) in International Journal of Energy Studies
- Vol. 8 (3) , 535-556
Investigation of conversion of a diesel engine to homogeneous charge compression ignition engine using n-heptane: A zero-dimensional modeling
Numerical methods are commonly used for analyzing combustion characteristics. Besides, they provide an opportunity to predict emissions of an engine. In this paper, the conversion of a single-cylinder diesel engine to HCCI combustion model is investigated with AVL Boost v2021R2. The model was used to simulate the power, emission, bsfc value. In-cylinder pressure results also are obtained from the model. Verification of the model is conducted with experimental data from the literature. The differentiation between the numerical and experimental results remained below 8.9% for the power, below 6.62% for bsfc. In addition to this, the model gave maximum pressure values with an accuracy of ± 1%, and maximum HRR values with an accuracy of ± 2%. Maximum HRR values and in-cylinder pressure curves for 1200-2400 rpm were obtained with acceptable accuracy. Besides, the operating range of an HCCI engine fueled with n-heptane was investigated using a zero-dimensional single-zone model with reduced fuel chemistry. The compression ratio and inlet air temperature effect on HCCI combustion were analyzed. The increasing the air inlet temperature to 40oC from 20oC, increases the lowest air-fuel ratio about 6.6% which the engine can operate without entering the knock zone, at 17.5 CR at 1200rpm.
- 31 October 2021
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 41 (2) , 239-247
EFFECTS OF PREHEATER LOAD AND LOCATION ON THE CATALYTIC CONVERTER EFFICIENCY DURING COLD START AND IDLING CONDITIONS
Exhaust emissions are significant pollutants that affect urban lifestyles. There are several regulations related to the exhaust emissions of both gasoline and diesel engines. In this study, the effects of a controlled heating of the exhaust line before the catalytic converter on the converter efficiency are experimentally investigated. Experiments were conducted based on either discrete or cold start conditions. For discrete conditions, the engine was operated until it reached normal and steady state operating conditions. Then, the engine was stopped until the catalytic converter surface temperature reached the ambient temperature. The experiments were first started without additional heating and then continued with different heating loads. In the second stage, the catalytic converter behavior and conversion efficiency under cold start conditions were investigated. The exhaust gas after the exhaust manifold was preheated with different heating loads for the first 150 seconds after the start of the engine; however, the exhaust line was heated 15 s before starting the engine. The effects of the location, length and heat loads of the electrical resistances on the catalytic converter behavior were investigated. After all of the experiments, it was concluded that with the appropriate location and heating loads, for discrete operating conditions, the hydrocarbon (HC) and carbon monoxide (CO) emission conversion efficiencies reached nearly 100 % after 50 s of starting the engine. For cold start conditions, the hydrocarbon (HC) and carbon monoxide (CO) emission conversion efficiencies reached 35 % and 80 %, respectively.
- 31 October 2021
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 41 (2) , 239-247
EFFECTS OF PREHEATER LOAD AND LOCATION ON THE CATALYTIC CONVERTER EFFICIENCY DURING COLD START AND IDLING CONDITIONS
Exhaust emissions are significant pollutants that affect urban lifestyles. There are several regulations related to the exhaust emissions of both gasoline and diesel engines. In this study, the effects of a controlled heating of the exhaust line before the catalytic converter on the converter efficiency are experimentally investigated. Experiments were conducted based on either discrete or cold start conditions. For discrete conditions, the engine was operated until it reached normal and steady state operating conditions. Then, the engine was stopped until the catalytic converter surface temperature reached the ambient temperature. The experiments were first started without additional heating and then continued with different heating loads. In the second stage, the catalytic converter behavior and conversion efficiency under cold start conditions were investigated. The exhaust gas after the exhaust manifold was preheated with different heating loads for the first 150 seconds after the start of the engine; however, the exhaust line was heated 15 s before starting the engine. The effects of the location, length and heat loads of the electrical resistances on the catalytic converter behavior were investigated. After all of the experiments, it was concluded that with the appropriate location and heating loads, for discrete operating conditions, the hydrocarbon (HC) and carbon monoxide (CO) emission conversion efficiencies reached nearly 100 % after 50 s of starting the engine. For cold start conditions, the hydrocarbon (HC) and carbon monoxide (CO) emission conversion efficiencies reached 35 % and 80 %, respectively.
- 8 July 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (3) , 1-11
Experimental investigation of cold start emission using preheating system on the exhaust line at the idle conditions on a spark ignition engine
- 8 July 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (3) , 1-11
Experimental investigation of cold start emission using preheating system on the exhaust line at the idle conditions on a spark ignition engine
- 1 June 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (2) , 715-722
Boru İçerisine Yerleştirilen Gözenekli Bir Kanatçığın Akışkan Akışı ve Sıcaklığına Etkisinin Sayısal Olarak İncelenmesi
En tr Energy is consumed continuously by people in their daily lives. People use energy in the devices, vehicles, etc. they demand efficient use of energy. Energy efficiency is important not only in the tools and equipment used by people, but also in all sectors where energy is produced and used. One of the equipment used for heating and cooling processes is heat exchangers. There are various types of heat exchangers used for different purposes. In this study, a double pipe heat exchanger is considered. It is aimed to increase the heat transfer with the fin added to the inner tube. In this study, the effect of a porous fin made for heating the air passing through the pipe on the flow and temperature of the combustion air was investigated. The effect of the height of the fin (h =3 mm, 5 mm, 7 mm), its porosity (= 0.1, 0.2, 0.3), and the laminar (Re = 100, 250, 500) and turbulent (Re = 25000, 45000, 60000) flow have been investigated. When the friction factor is examined, it decreases with the flow velocity and increases with the height of the fin. While the flow velocity and temperature difference decreases under laminar conditions, the height of the blade increases with the temperature difference in turbulent flows. İnsanlar günlük yaşantılarında sürekli olarak enerji tüketmektedirler. İnsanlar kullandıkları, cihazlarda, taşıtlarda vb. enerjinin verimli olarak kullanılmasını talep etmektedirler. Enerji verimliliği sadece insanların kullandığı araç ve gereçlerde değil enerjinin üretilip kullanıldığı tüm sektörlerde önemlidir. Isıtma ve soğutma işlemleri için kullanılan donanımlardan birisi de ısı değiştiricilerdir. Çeşitli tiplerde farklı amaçlar için kullanılan ısı değiştiriciler mevcuttur. Bu çalışmada eş eksenli çift borulu bir ısı değiştirici ele alınmıştır. İçteki boru içerisine eklenen kanatçık ile ısı transferinin artırılması amaçlanmıştır. Bu çalışmada, boru içinden geçen havanın ısıtılması için yapılan gözenekli bir kanatçığın yakma havasının akışına ve sıcaklığına olan etkisi incelenmiştir. Kanatçığın yüksekliğinin etkisi (h =3 mm, 5 mm, 7 mm), gözenekliliği ( = 0.1, 0.2, 0.3), akışın laminer (Re = 100, 250, 500) ve türbülanslı (Re = 25000, 45000, 60000) olma durumu incelenmiştir. Yapılan bu çalışmada elde edilen sonuçlar incelendiğinde, sürtünme faktörünün akış hızı ile azaldığı, kanatçık yüksekliğinin artışı ile arttığı görülmüştür. Laminer şartlarda akış hızının artışı ile sıcaklık farkı azalırken, türbülanslı akışlarda ise kanatçık yüksekliğinin artışı ile sıcaklık farkının arttığı belirlenmiştir.
- 1 June 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (2) , 715-722
Boru İçerisine Yerleştirilen Gözenekli Bir Kanatçığın Akışkan Akışı ve Sıcaklığına Etkisinin Sayısal Olarak İncelenmesi
En tr Energy is consumed continuously by people in their daily lives. People use energy in the devices, vehicles, etc. they demand efficient use of energy. Energy efficiency is important not only in the tools and equipment used by people, but also in all sectors where energy is produced and used. One of the equipment used for heating and cooling processes is heat exchangers. There are various types of heat exchangers used for different purposes. In this study, a double pipe heat exchanger is considered. It is aimed to increase the heat transfer with the fin added to the inner tube. In this study, the effect of a porous fin made for heating the air passing through the pipe on the flow and temperature of the combustion air was investigated. The effect of the height of the fin (h =3 mm, 5 mm, 7 mm), its porosity (= 0.1, 0.2, 0.3), and the laminar (Re = 100, 250, 500) and turbulent (Re = 25000, 45000, 60000) flow have been investigated. When the friction factor is examined, it decreases with the flow velocity and increases with the height of the fin. While the flow velocity and temperature difference decreases under laminar conditions, the height of the blade increases with the temperature difference in turbulent flows. İnsanlar günlük yaşantılarında sürekli olarak enerji tüketmektedirler. İnsanlar kullandıkları, cihazlarda, taşıtlarda vb. enerjinin verimli olarak kullanılmasını talep etmektedirler. Enerji verimliliği sadece insanların kullandığı araç ve gereçlerde değil enerjinin üretilip kullanıldığı tüm sektörlerde önemlidir. Isıtma ve soğutma işlemleri için kullanılan donanımlardan birisi de ısı değiştiricilerdir. Çeşitli tiplerde farklı amaçlar için kullanılan ısı değiştiriciler mevcuttur. Bu çalışmada eş eksenli çift borulu bir ısı değiştirici ele alınmıştır. İçteki boru içerisine eklenen kanatçık ile ısı transferinin artırılması amaçlanmıştır. Bu çalışmada, boru içinden geçen havanın ısıtılması için yapılan gözenekli bir kanatçığın yakma havasının akışına ve sıcaklığına olan etkisi incelenmiştir. Kanatçığın yüksekliğinin etkisi (h =3 mm, 5 mm, 7 mm), gözenekliliği ( = 0.1, 0.2, 0.3), akışın laminer (Re = 100, 250, 500) ve türbülanslı (Re = 25000, 45000, 60000) olma durumu incelenmiştir. Yapılan bu çalışmada elde edilen sonuçlar incelendiğinde, sürtünme faktörünün akış hızı ile azaldığı, kanatçık yüksekliğinin artışı ile arttığı görülmüştür. Laminer şartlarda akış hızının artışı ile sıcaklık farkı azalırken, türbülanslı akışlarda ise kanatçık yüksekliğinin artışı ile sıcaklık farkının arttığı belirlenmiştir.
- 1 January 2020
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 40 (2) , 319-334
EMERGENCY SIMULATION IN A LONG HIGHWAY TUNNEL
In regions that are difficult to overcome geographically in road transport, tunnels both shorten the road to be covered and save fuel. It is the worst scenario that a vehicle can burn in a tunnel. There have been major tunnel fires in the world that have resulted in people's lives. In our country, long highway tunnels such as the Ovit, Kop and Zigana tunnels are being built. In this study, emergency modeling was carried out for vehicle fire (30 MW) in a long road tunnel (14.5 km). The critical point for the emergency was determined and the 1000 m long region was examined on a scale of 1/100. Ansys Fluent was used in the study. Turbulent flow conditions are taken into account. Temperature distribution, carbon monoxide (CO) emission distribution and velocity distributions in the region where the fire is located were examined. Results are given in graphs and interpreted. When the temperature values are examined, the average temperature values in the fire zone were obtained above 400 K in the first 30 m. It was obtained that the CO values did not fall below 400 ppm until the firing shaft, especially in the first 50 m, above 1000 ppm on average.
- 1 January 2020
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 40 (2) , 319-334
EMERGENCY SIMULATION IN A LONG HIGHWAY TUNNEL
In regions that are difficult to overcome geographically in road transport, tunnels both shorten the road to be covered and save fuel. It is the worst scenario that a vehicle can burn in a tunnel. There have been major tunnel fires in the world that have resulted in people's lives. In our country, long highway tunnels such as the Ovit, Kop and Zigana tunnels are being built. In this study, emergency modeling was carried out for vehicle fire (30 MW) in a long road tunnel (14.5 km). The critical point for the emergency was determined and the 1000 m long region was examined on a scale of 1/100. Ansys Fluent was used in the study. Turbulent flow conditions are taken into account. Temperature distribution, carbon monoxide (CO) emission distribution and velocity distributions in the region where the fire is located were examined. Results are given in graphs and interpreted. When the temperature values are examined, the average temperature values in the fire zone were obtained above 400 K in the first 30 m. It was obtained that the CO values did not fall below 400 ppm until the firing shaft, especially in the first 50 m, above 1000 ppm on average.