Tolgahan Civek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tolgahan Civek has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Nuri Şen
Düzce University
9 shared publications - Oktay Elkoca
Researcher Zonguldak Turkey 67300
2 shared publications E. Çevik
Karabuk University, Faculty of Engineering, Department of Mechanical Engineering, 78050 Karabuk, Turkey
1 shared publication- Elifnaz Baba
Duzce Universitesi
1 shared publication - Ezgi Tongü
Düzce University
1 shared publication - Fatih Helimergin
Duzce Universitesi
1 shared publication
Latest Publications
- 21 January 2026
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 14 (1) , 38-48
Evaluation of Springback and Post-Formed Mechanical Properties of DP800 Steel in Warm-Hat-Shaped Bending Process
Springback is one of the most undesired outcomes of a bending process since it creates problems during the assembly of formed products and leads to waste time and energy. Heating the sheet metal before the bending process is an application that is widely used in the industry to alleviate the undesired effects of springback. However, in many cases, the consequences of a warm or hot bending process on the mechanical properties of bent products are not thoroughly considered. In this study, the effects of the warm bending process combined with the process parameters such as blank-holder force and lubrication on the springback behaviour of DP800 steel have been examined. Additionally, the post-mechanical properties of the bent specimens have been investigated. For this, sheets of DP800 steels have been bent to a hat-shaped product at four different temperatures (25 ℃, 200 ℃, 300 ℃, 400 ℃), by using three different blank-holder force (25bar, 75bar, 125 bar), and two different lubricants (graphite and teflon). According to the results, it has been shown that reducing the blank-holder force and applying a better lubricant (teflon) has had a considerable effect in attaining a lower springback. Additionally, while increasing the temperature has positively impacted the springback, it has been found that the post-mechanical strength of bent sheets at warm temperatures has not shown a significant reduction.
- 21 January 2026
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 14 (1) , 38-48
Evaluation of Springback and Post-Formed Mechanical Properties of DP800 Steel in Warm-Hat-Shaped Bending Process
Springback is one of the most undesired outcomes of a bending process since it creates problems during the assembly of formed products and leads to waste time and energy. Heating the sheet metal before the bending process is an application that is widely used in the industry to alleviate the undesired effects of springback. However, in many cases, the consequences of a warm or hot bending process on the mechanical properties of bent products are not thoroughly considered. In this study, the effects of the warm bending process combined with the process parameters such as blank-holder force and lubrication on the springback behaviour of DP800 steel have been examined. Additionally, the post-mechanical properties of the bent specimens have been investigated. For this, sheets of DP800 steels have been bent to a hat-shaped product at four different temperatures (25 ℃, 200 ℃, 300 ℃, 400 ℃), by using three different blank-holder force (25bar, 75bar, 125 bar), and two different lubricants (graphite and teflon). According to the results, it has been shown that reducing the blank-holder force and applying a better lubricant (teflon) has had a considerable effect in attaining a lower springback. Additionally, while increasing the temperature has positively impacted the springback, it has been found that the post-mechanical strength of bent sheets at warm temperatures has not shown a significant reduction.
- 7 January 2026
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
Deep drawing ability of TRIP-aided DP steel under a non-isothermal warm deep drawing process
The formability of transformation-induced plasticity-assisted steels is significantly influenced by the transformation-induced plasticity transformation mechanism (transformation of retained austenite to martensite) that occurs during deformation. However, the additional strain hardening that develops in the flange regions during the deep drawing process adversely affects their deep drawability. Therefore, an advanced method is required to enhance the deep drawing performance of transformation-induced plasticity-assisted steels. In this study, a novel non-isothermal warm deep drawing process has been developed to enable controlled transformation-induced plasticity during forming. In this process, the flange region of the sheet metal is heated to elevated temperatures (50 °C, 100 °C and 150 °C), while the centre and wall regions are continuously cooled by liquid nitrogen throughout deformation. This thermal gradient is designed to suppress the transformation-induced plasticity effect in the flange region while activating it in the centre and wall regions of the sheet during forming. Furthermore, a simplified version of this setup was modelled using finite element analysis, employing the Modified Mohr–Coulomb damage model as a failure criterion to predict the limiting drawing ratio. Experimental results demonstrated a 12.67% improvement in the limiting drawing ratio at 150 °C using the proposed non-isothermal approach. The simulation results closely matched the experimental findings, confirming the predictive accuracy of the finite element analysis model.
- 7 January 2026
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
Deep drawing ability of TRIP-aided DP steel under a non-isothermal warm deep drawing process
The formability of transformation-induced plasticity-assisted steels is significantly influenced by the transformation-induced plasticity transformation mechanism (transformation of retained austenite to martensite) that occurs during deformation. However, the additional strain hardening that develops in the flange regions during the deep drawing process adversely affects their deep drawability. Therefore, an advanced method is required to enhance the deep drawing performance of transformation-induced plasticity-assisted steels. In this study, a novel non-isothermal warm deep drawing process has been developed to enable controlled transformation-induced plasticity during forming. In this process, the flange region of the sheet metal is heated to elevated temperatures (50 °C, 100 °C and 150 °C), while the centre and wall regions are continuously cooled by liquid nitrogen throughout deformation. This thermal gradient is designed to suppress the transformation-induced plasticity effect in the flange region while activating it in the centre and wall regions of the sheet during forming. Furthermore, a simplified version of this setup was modelled using finite element analysis, employing the Modified Mohr–Coulomb damage model as a failure criterion to predict the limiting drawing ratio. Experimental results demonstrated a 12.67% improvement in the limiting drawing ratio at 150 °C using the proposed non-isothermal approach. The simulation results closely matched the experimental findings, confirming the predictive accuracy of the finite element analysis model.
- Open Access
- 25 June 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- p. 651-661
Investigation of the Flow Behaviour of Martensitic Steel at Elevated Temperatures Via Uniaxial Tensile Tests
In recent years, advanced high strength steels have been the main choice of automobile manufacturers due to their excellent strengths and decent formability. In this study, the forming behaviour of a martensitic steel (MART 1200) at elevated temperatures, where higher formability and an acceptable strength can be achieved, has been investigated. For this purpose, tensile test experiments have been conducted at room temperature, 175°C, 275°C, 375°C and 475°C in two different strain rates (0.005 s–1, 0.05 s–1). The flow behaviour, elongation capacity, strain rate sensitivity, strain hardening and strain hardening rate of MART1200 have been investigated and fracture surfaces and microstructures have been examined by scanning electron microscope. It has been shown that the strain rate sensitivity of MART1200 increases significantly after 275°C and, for the higher strain rate, a significant improvement up to 80% in the elongation capacity has been achieved in return for a 19% strength reduction at 375°C.
- 25 June 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- p. 651-661
Open AccessInvestigation of the Flow Behaviour of Martensitic Steel at Elevated Temperatures Via Uniaxial Tensile Tests
In recent years, advanced high strength steels have been the main choice of automobile manufacturers due to their excellent strengths and decent formability. In this study, the forming behaviour of a martensitic steel (MART 1200) at elevated temperatures, where higher formability and an acceptable strength can be achieved, has been investigated. For this purpose, tensile test experiments have been conducted at room temperature, 175°C, 275°C, 375°C and 475°C in two different strain rates (0.005 s–1, 0.05 s–1). The flow behaviour, elongation capacity, strain rate sensitivity, strain hardening and strain hardening rate of MART1200 have been investigated and fracture surfaces and microstructures have been examined by scanning electron microscope. It has been shown that the strain rate sensitivity of MART1200 increases significantly after 275°C and, for the higher strain rate, a significant improvement up to 80% in the elongation capacity has been achieved in return for a 19% strength reduction at 375°C.
- Open Access
- 30 April 2025
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 13 (2) , 735-751
Prediction of Deep Drawing Ratio for DP800 Steel by Using Modified-Mohr-Coulomb Damage Criteria
The demand for low-cost production in vehicle manufacturing while complying with the safety and environmental regulations is an enormous challenge. To comply with these challenges, sheet metal forming industries now extensively use advanced high-strength steels (AHSSs) in their products. However, due to excellent strength levels of AHSSs, problems arising in their forming stage, such as large spring-back and fracture, hinder the manufacturing process. At this stage, implementing finite element analysis (FEA) in the design processes greatly improves manufacturing processes since it allows determining possible forming errors before the actual forming process. In this study, the formability of DP800 steel has been investigated by carrying out deep drawing experiments. For that, a series of circular sheet metals, whose diameters were incrementally increased, have been deep drawn to a cup shape to determine the limiting drawing ratio (LDR). Additionally, Modified Mohr-Coulomb damage model has been utilised to predict the LDR in FEA. It has been found that the LDR of DP800 is 2.13 and the implemented damage model can successfully predict the LDR within only 2.35% error.
- 30 April 2025
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 13 (2) , 735-751
Open AccessPrediction of Deep Drawing Ratio for DP800 Steel by Using Modified-Mohr-Coulomb Damage Criteria
The demand for low-cost production in vehicle manufacturing while complying with the safety and environmental regulations is an enormous challenge. To comply with these challenges, sheet metal forming industries now extensively use advanced high-strength steels (AHSSs) in their products. However, due to excellent strength levels of AHSSs, problems arising in their forming stage, such as large spring-back and fracture, hinder the manufacturing process. At this stage, implementing finite element analysis (FEA) in the design processes greatly improves manufacturing processes since it allows determining possible forming errors before the actual forming process. In this study, the formability of DP800 steel has been investigated by carrying out deep drawing experiments. For that, a series of circular sheet metals, whose diameters were incrementally increased, have been deep drawn to a cup shape to determine the limiting drawing ratio (LDR). Additionally, Modified Mohr-Coulomb damage model has been utilised to predict the LDR in FEA. It has been found that the LDR of DP800 is 2.13 and the implemented damage model can successfully predict the LDR within only 2.35% error.
- Open Access
- 31 March 2025
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 9 (1) , 158-165
The Effect of Heating Time in Induction Hardening Process on the Hardness Profile of a Ball Stud: A Case Study
The induction hardening method is widely used for the surface hardening of industrial products to improve the resistance of the material to various failure modes such as fatigue, wear, etc. Hence, surface hardening of parts that undergo repetitive forces and that work in close contact with other moving components plays a significant role in their service life. In this study, an automotive ball stud part, which is a highly prone part to fatigue and wear failures, has been induction hardened for varying amounts of heating time (2s, 3s, 4s and 5s) under constant power (135 A) and frequency (50 Hz). The hardness, the hardness depth and the microstructure of the parts have been investigated utilizing hardness tests and optical microscopy. Additionally, the effect of different cooling durations (3s, 5s, and 7s) and the resistance of the parts to the bending force has also been examined. The results show that the increase in heating time has an increasing impact on the hardness of parts and the hardness depth. The bending forces have also been shown to be increasing by increasing the heating time. The highest hardness level, hardness depth and bending resistance have been found when induction heating the specimens for 5s. Increasing the cooling time has not led to a considerable variation in the hardness profile of the specimens.
- 31 March 2025
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 9 (1) , 158-165
Open AccessThe Effect of Heating Time in Induction Hardening Process on the Hardness Profile of a Ball Stud: A Case Study
The induction hardening method is widely used for the surface hardening of industrial products to improve the resistance of the material to various failure modes such as fatigue, wear, etc. Hence, surface hardening of parts that undergo repetitive forces and that work in close contact with other moving components plays a significant role in their service life. In this study, an automotive ball stud part, which is a highly prone part to fatigue and wear failures, has been induction hardened for varying amounts of heating time (2s, 3s, 4s and 5s) under constant power (135 A) and frequency (50 Hz). The hardness, the hardness depth and the microstructure of the parts have been investigated utilizing hardness tests and optical microscopy. Additionally, the effect of different cooling durations (3s, 5s, and 7s) and the resistance of the parts to the bending force has also been examined. The results show that the increase in heating time has an increasing impact on the hardness of parts and the hardness depth. The bending forces have also been shown to be increasing by increasing the heating time. The highest hardness level, hardness depth and bending resistance have been found when induction heating the specimens for 5s. Increasing the cooling time has not led to a considerable variation in the hardness profile of the specimens.
- Open Access
- 29 December 2023
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 11 (5) , 2309-2320
Determination of Modified Mohr-Coulomb Damage Model Parameters for DH780 Steel in Finite Element Analysis
In sheet metal forming processes, tearing problems might be occasionally encountered due to many reasons such as incorrect forming parameters. The trial and error methods that are used to solve such problems, on many occasions, are time-consuming and inefficient in terms of finding the correct forming parameters or die design for the forming process. The finite element analysis method, on the other hand, can be used as a tool that is both time and cost-saving. However, in order to effectively exploit the use of finite element analysis in sheet metal forming operations, the material that is used to be formed needs to be well characterized in terms of its hardening behaviour and failure criteria. In this study, a TRIP-aided DP steel (DH780) has been tensile tested in three different deformation conditions (uniaxial, plane stress and shear) and the parameters of its hardening model (Hollomon) and failure criteria (Modified Mohr-Coulomb) have been determined. According to the simulation results, obtained hardening parameters are able to describe the flow behaviour of the steel and the used failure criterion is able to predict the experimental failure correctly in each deformation condition.
- 29 December 2023
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 11 (5) , 2309-2320
Open AccessDetermination of Modified Mohr-Coulomb Damage Model Parameters for DH780 Steel in Finite Element Analysis
In sheet metal forming processes, tearing problems might be occasionally encountered due to many reasons such as incorrect forming parameters. The trial and error methods that are used to solve such problems, on many occasions, are time-consuming and inefficient in terms of finding the correct forming parameters or die design for the forming process. The finite element analysis method, on the other hand, can be used as a tool that is both time and cost-saving. However, in order to effectively exploit the use of finite element analysis in sheet metal forming operations, the material that is used to be formed needs to be well characterized in terms of its hardening behaviour and failure criteria. In this study, a TRIP-aided DP steel (DH780) has been tensile tested in three different deformation conditions (uniaxial, plane stress and shear) and the parameters of its hardening model (Hollomon) and failure criteria (Modified Mohr-Coulomb) have been determined. According to the simulation results, obtained hardening parameters are able to describe the flow behaviour of the steel and the used failure criterion is able to predict the experimental failure correctly in each deformation condition.
- Open Access
- 30 June 2023
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 7 (2) , 104-111
Assessment of Conical Die Deep Drawing Ability of DP800 and MART1400 Ad-vanced High Strength Steels
Deep drawing is one of the most important and vastly conducted sheet metal forming method. Thus, even small improvements achieved on the deep drawability of sheet metals significantly increases the ability of sheet metal to be formed into more complex products. Advanced high strength steels (AHSSs) are one of the most popular steels in the automotive industry due to their high strengths. However, their low ductility causes considerable splitting problems on the shop floors. In this study, deep drawing experiments have been conducted in conical dies with four different angles (0⁰, 7.5⁰, 12.5⁰, and 20⁰) for DP800 and MART1400 steels to observe whether a higher deep drawing ratio (DDR) can be achieved by deep drawing in conical dies for AHSSs. In addition, finite element analysis (FEA) has been utilized to estimate the DDR for each types of steels in different conical die setups. It has been observed that the deep drawing ability of MART1400 steel has not improved in any of the conical die setups. However, DDR of DP800 has slightly increased by 2.46% by deep drawing with 20⁰ die angle. A good agreement with the numerical and experimental results has been achieved.
- 30 June 2023
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 7 (2) , 104-111
Open AccessAssessment of Conical Die Deep Drawing Ability of DP800 and MART1400 Ad-vanced High Strength Steels
Deep drawing is one of the most important and vastly conducted sheet metal forming method. Thus, even small improvements achieved on the deep drawability of sheet metals significantly increases the ability of sheet metal to be formed into more complex products. Advanced high strength steels (AHSSs) are one of the most popular steels in the automotive industry due to their high strengths. However, their low ductility causes considerable splitting problems on the shop floors. In this study, deep drawing experiments have been conducted in conical dies with four different angles (0⁰, 7.5⁰, 12.5⁰, and 20⁰) for DP800 and MART1400 steels to observe whether a higher deep drawing ratio (DDR) can be achieved by deep drawing in conical dies for AHSSs. In addition, finite element analysis (FEA) has been utilized to estimate the DDR for each types of steels in different conical die setups. It has been observed that the deep drawing ability of MART1400 steel has not improved in any of the conical die setups. However, DDR of DP800 has slightly increased by 2.46% by deep drawing with 20⁰ die angle. A good agreement with the numerical and experimental results has been achieved.
- 1 May 2023
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 50 (9) , 1311-1320
Investigation of the effects of lubrication type, blankholder force and force holding time on the spring-back behaviour for hat-shaped MART steels
In this study, hat-shaped bending experiments have been conducted on MART1200 and MART1400 Ultra-High-Strength Steels (UHSS). To investigate the influence of different lubrication conditions, on the spring-back, three different lubricant types (Graphite, Teflon film and Teflon film + Graphite) have been used in the experiments. A constant 6.5 tons of bottoming force has been applied at the end of the bending stroke and the force has been held on the samples for 0, 10s and 60s to observe the effect of force holding time on the spring-back. In addition, the effect of blankholder force on the spring-back has also been investigated for MART1400 steel. It has been found that the decrease of blankholder force and the friction between the die and sheet interfaces has considerably reduced the spring-back in the sidewalls and flange regions and also lowered the side wall curl. It has been revealed through finite element analysis that the sheet bottom has suffered a larger deformation in lower friction conditions and blankholder forces and caused in the reduction of spring-back.
- 1 May 2023
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 50 (9) , 1311-1320
Investigation of the effects of lubrication type, blankholder force and force holding time on the spring-back behaviour for hat-shaped MART steels
In this study, hat-shaped bending experiments have been conducted on MART1200 and MART1400 Ultra-High-Strength Steels (UHSS). To investigate the influence of different lubrication conditions, on the spring-back, three different lubricant types (Graphite, Teflon film and Teflon film + Graphite) have been used in the experiments. A constant 6.5 tons of bottoming force has been applied at the end of the bending stroke and the force has been held on the samples for 0, 10s and 60s to observe the effect of force holding time on the spring-back. In addition, the effect of blankholder force on the spring-back has also been investigated for MART1400 steel. It has been found that the decrease of blankholder force and the friction between the die and sheet interfaces has considerably reduced the spring-back in the sidewalls and flange regions and also lowered the side wall curl. It has been revealed through finite element analysis that the sheet bottom has suffered a larger deformation in lower friction conditions and blankholder forces and caused in the reduction of spring-back.
- 3 October 2022
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 6 (3) , 214-220
Effect of Different Conical Punch Angle Geometries and the Initial Hole Diameters on the Hole Expansion Ratio of DP steels
In the recent decade, advanced high strength steels (AHSS) have gained a great popularity in the automotive manufacturing industries due to their high strength to weight ratio, which significantly improves the safety of the manufactured automobiles while reducing the weight and thus, enabling to improve the fuel efficiency. However, it is known that some types of AHSSs, especially DP steels, are highly susceptible to edge cracking behaviour during the forming operations. Edge cracking behaviour is generally investigated with a 600 conical punch as suggested by the ISO 16630 standard. However, in this study, to observe the behaviour of edge cracking ability of DP steels under different conical punch angles for different initial hole diameters, hole expansion tests have been performed with conical punches with three different angles (300 ,600, 900) for three different initial hole diameters (14, 16, 18 mm). The results have shown that the hole expansion ratio (HER) does not differ considerably with the variation of the conical punch angle and the initial hole diameter due to low fracture strain of DP steels observed after hole expansion tests. The major factor for the edge stretching ability of DP steels have been observed to be microstructure rather than geometrical factors such as conical punch angles.
- 3 October 2022
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 6 (3) , 214-220
Effect of Different Conical Punch Angle Geometries and the Initial Hole Diameters on the Hole Expansion Ratio of DP steels
In the recent decade, advanced high strength steels (AHSS) have gained a great popularity in the automotive manufacturing industries due to their high strength to weight ratio, which significantly improves the safety of the manufactured automobiles while reducing the weight and thus, enabling to improve the fuel efficiency. However, it is known that some types of AHSSs, especially DP steels, are highly susceptible to edge cracking behaviour during the forming operations. Edge cracking behaviour is generally investigated with a 600 conical punch as suggested by the ISO 16630 standard. However, in this study, to observe the behaviour of edge cracking ability of DP steels under different conical punch angles for different initial hole diameters, hole expansion tests have been performed with conical punches with three different angles (300 ,600, 900) for three different initial hole diameters (14, 16, 18 mm). The results have shown that the hole expansion ratio (HER) does not differ considerably with the variation of the conical punch angle and the initial hole diameter due to low fracture strain of DP steels observed after hole expansion tests. The major factor for the edge stretching ability of DP steels have been observed to be microstructure rather than geometrical factors such as conical punch angles.