Marcin Zyskowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Marcin Zyskowski has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Steven Kleijn
SMART Photonics BV Eindhoven The Netherlands
2 shared publications - Akanksha Kapoor
Univ. Grenoble Alpes, CEA, Grenoble INP, IRIG, PHELIQS, NPSC, Grenoble, 38000, France
1 shared publication Francisco J. Diaz-Otero
1 shared publication- Francisco Javier Díaz Otero
University of Vigo
1 shared publication - Nick de Louw
SMART Photonics 1 , High Tech Campus 37, 5656 AE Eindhoven, The Netherlands
1 shared publication Steven E. F. Kleijn
1 shared publication
Latest Publications
- 16 December 2024
- Published by Wiley in Physica Status Solidi (b)
- Vol. 262 (11)
Influence of Precursor Concentration on the Determination of AlInGaAs Solid‐State Compositions Grown by Metalorganic Vapor Phase Epitaxy
The epitaxial growth of AlInGaAs alloys on InP allows the manufacture of semiconductor lasers that emit in the wavelength range between 1200 and 1600 nm in which the optical telecommunication bands lie. These alloys are particularly well suited for manufacturing lasers intended for operation at higher temperatures. A model relating the metalorganic vapor phase epitaxy (MOVPE) growth settings for AlInGaAs on InP to the resultant bandgap energy is presented, for strained and unstrained compositions, based on a new dataset measured on epitaxial layers grown in a novel planetary epitaxy reactor, using the 12x4 inch configuration. Elemental analysis (ICP‐OES) was employed to relate the growth settings to the solid‐state composition of the resulting alloy, to ensure our model takes meaningful input. It was found that the MOVPE growth settings and the solid‐state composition as determined by ICP‐OES only showed a one‐to‐one correspondence once the right set of vapor pressure coefficients for the precursors was chosen.
- 16 December 2024
- Published by Wiley in Physica Status Solidi (b)
- Vol. 262 (11)
Influence of Precursor Concentration on the Determination of AlInGaAs Solid‐State Compositions Grown by Metalorganic Vapor Phase Epitaxy
The epitaxial growth of AlInGaAs alloys on InP allows the manufacture of semiconductor lasers that emit in the wavelength range between 1200 and 1600 nm in which the optical telecommunication bands lie. These alloys are particularly well suited for manufacturing lasers intended for operation at higher temperatures. A model relating the metalorganic vapor phase epitaxy (MOVPE) growth settings for AlInGaAs on InP to the resultant bandgap energy is presented, for strained and unstrained compositions, based on a new dataset measured on epitaxial layers grown in a novel planetary epitaxy reactor, using the 12x4 inch configuration. Elemental analysis (ICP‐OES) was employed to relate the growth settings to the solid‐state composition of the resulting alloy, to ensure our model takes meaningful input. It was found that the MOVPE growth settings and the solid‐state composition as determined by ICP‐OES only showed a one‐to‐one correspondence once the right set of vapor pressure coefficients for the precursors was chosen.
- Open Access
- 26 December 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (24)
Strained AlGaInAs on InP: Bandgap dependence on composition—Model benchmark and optimization
Influence of chemical composition on the bandgap of AlGaInAs deposited on InP is often calculated using models for unstrained composition and then corrected for strain-induced bandgap energy changes using deformation potentials. This method relies on up to 25 coefficients, many of which are burdened with large uncertainty. In this paper, a large set of experimental data is used to verify the accuracy of existing approaches and to search for optimal deformation potentials. It is shown that the main source of inaccuracy is not the deformation potentials, but the unstrained bandgap formulas. Additionally, a novel model is proposed, yielding the highest accuracy on our dataset. For the first time, composition determination of a quaternary alloy on InP is reported using inductively coupled plasma-optical emission spectrometry, which is used as a benchmark for modeling.
- 26 December 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (24)
Open AccessStrained AlGaInAs on InP: Bandgap dependence on composition—Model benchmark and optimization
Influence of chemical composition on the bandgap of AlGaInAs deposited on InP is often calculated using models for unstrained composition and then corrected for strain-induced bandgap energy changes using deformation potentials. This method relies on up to 25 coefficients, many of which are burdened with large uncertainty. In this paper, a large set of experimental data is used to verify the accuracy of existing approaches and to search for optimal deformation potentials. It is shown that the main source of inaccuracy is not the deformation potentials, but the unstrained bandgap formulas. Additionally, a novel model is proposed, yielding the highest accuracy on our dataset. For the first time, composition determination of a quaternary alloy on InP is reported using inductively coupled plasma-optical emission spectrometry, which is used as a benchmark for modeling.
- Open Access
- 7 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Practical nuances of laser diode characterisation: a methods article
This article is supposed to facilitate laser diode characterization. Measuring the performance of a laser diode is a multi-faceted problem, often mixing theoretical and practical issues. This paper offers insights that may be helpful in troubleshooting the measurement system and contains references that present useful theoretical tools.
- 7 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessPractical nuances of laser diode characterisation: a methods article
This article is supposed to facilitate laser diode characterization. Measuring the performance of a laser diode is a multi-faceted problem, often mixing theoretical and practical issues. This paper offers insights that may be helpful in troubleshooting the measurement system and contains references that present useful theoretical tools.