Jiaxin Pan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiaxin Pan has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Wanbo Wang
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang, China
2 shared publications - Xunnian Wang
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China
2 shared publications - Chaoqun Li
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China
1 shared publication - Chen Qin
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China
1 shared publication - Kun Tang
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China
1 shared publication - Qixiang Sun
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China
1 shared publication
Latest Publications
- Open Access
Experimental Investigation on Flow Control over a Circular Cylinder Using Antiphase Pulsed Jets
To investigate the flow control characteristics of antiphase pulsed jet technology and explore a more efficient method to control unsteady flow with minimal impact on flow turbulence, wind tunnel experiments were conducted. The aim was to address the issue of flow separation control on the surface of a cylindrical model. The model had a diameter of 100 mm, and an experimental setup utilizing an antiphase pulsed jet excitation was developed. The optimisation of unsteady jet control involved adjusting parameters such as jet momentum coefficient, slot position, and excitation frequency. The flow separation control effect on the cylinder surface was compared between in-phase and antiphase pulsed jet using a particle image velocimetry (PIV) technique. The mechanisms of flow control for these two methods were analysed. The results showed that in still air, increasing the jet momentum led to a gradual decrease in the high-velocity region, which also moved away from the wall. Under incoming flow conditions, positioning the slot closer to the separation point resulted in better flow separation control, particularly when the excitation frequency matched the main flow frequency. Both in-phase and antiphase pulsed jet excitations effectively suppressed flow separation. In the near-wall region within the symmetric plane between the two slots, the antiphase excitation reduced the root mean square of velocity fluctuations by approximately 1.9% and increased the average velocity by approximately 15.5% compared to in-phase pulsed jet excitation. In-phase pulsed jets exhibited low-frequency, high-velocity characteristics near the separation point, while antiphase pulsed jets, due to the alternating discharge of the two jets, had a lesser impact on the flow field turbulence.
Open AccessExperimental Investigation on Flow Control over a Circular Cylinder Using Antiphase Pulsed Jets
To investigate the flow control characteristics of antiphase pulsed jet technology and explore a more efficient method to control unsteady flow with minimal impact on flow turbulence, wind tunnel experiments were conducted. The aim was to address the issue of flow separation control on the surface of a cylindrical model. The model had a diameter of 100 mm, and an experimental setup utilizing an antiphase pulsed jet excitation was developed. The optimisation of unsteady jet control involved adjusting parameters such as jet momentum coefficient, slot position, and excitation frequency. The flow separation control effect on the cylinder surface was compared between in-phase and antiphase pulsed jet using a particle image velocimetry (PIV) technique. The mechanisms of flow control for these two methods were analysed. The results showed that in still air, increasing the jet momentum led to a gradual decrease in the high-velocity region, which also moved away from the wall. Under incoming flow conditions, positioning the slot closer to the separation point resulted in better flow separation control, particularly when the excitation frequency matched the main flow frequency. Both in-phase and antiphase pulsed jet excitations effectively suppressed flow separation. In the near-wall region within the symmetric plane between the two slots, the antiphase excitation reduced the root mean square of velocity fluctuations by approximately 1.9% and increased the average velocity by approximately 15.5% compared to in-phase pulsed jet excitation. In-phase pulsed jets exhibited low-frequency, high-velocity characteristics near the separation point, while antiphase pulsed jets, due to the alternating discharge of the two jets, had a lesser impact on the flow field turbulence.
- Open Access
Experimental Investigation on the Combined Blowing Control of a Hybrid Wing Body Aircraft
Combined blowing was performed on a Hybrid Wing Body (HWB) aircraft through wind tunnel testing at a Reynolds number of 1.75 × 106. The full cycle of separation and reattachment under the control of combined blowing was implemented using Computational Fluid Dynamics (CFD), and the mechanism of combined blowing inhibiting separation was analyzed. The aerodynamic characteristics of the baseline and the independent effects of the blown deflected trailing edge (TE), blown leading edge (LE), and combined blowing on the TE and LE were investigated. The results clearly show that combined blowing can inhibit the development of cross-flow, reduce the accumulation of a boundary layer at the tip, and inhibit the flow separation effect. The effect of using seamless simple flaps alone to increase the lift is limited; blowing control is required to enhance the lift further. Applying the blown deflected TE can improve the lift linear segment, so that 30° flap achieves the lift gain of 40° flap without control, while the drag coefficient is approximately 0.02 smaller, but the stall gradually advances. Using the blown LE can significantly increase the stall angle from 12° to 18°. However, the lift linear segment remains unaffected. In particular, combined blowing can achieve the control effect of improving the lift linear segment, delaying stall, and decreasing drag. Moreover, the maximum lift coefficient is approximately 0.19, and the lift-to-drag ratio increment in the control state with a 30° flap deflection angle is above 2.2 in the angle of attack range of 4° to 12° compared to the uncontrolled state with a 40° flap deflection angle.
Open AccessExperimental Investigation on the Combined Blowing Control of a Hybrid Wing Body Aircraft
Combined blowing was performed on a Hybrid Wing Body (HWB) aircraft through wind tunnel testing at a Reynolds number of 1.75 × 106. The full cycle of separation and reattachment under the control of combined blowing was implemented using Computational Fluid Dynamics (CFD), and the mechanism of combined blowing inhibiting separation was analyzed. The aerodynamic characteristics of the baseline and the independent effects of the blown deflected trailing edge (TE), blown leading edge (LE), and combined blowing on the TE and LE were investigated. The results clearly show that combined blowing can inhibit the development of cross-flow, reduce the accumulation of a boundary layer at the tip, and inhibit the flow separation effect. The effect of using seamless simple flaps alone to increase the lift is limited; blowing control is required to enhance the lift further. Applying the blown deflected TE can improve the lift linear segment, so that 30° flap achieves the lift gain of 40° flap without control, while the drag coefficient is approximately 0.02 smaller, but the stall gradually advances. Using the blown LE can significantly increase the stall angle from 12° to 18°. However, the lift linear segment remains unaffected. In particular, combined blowing can achieve the control effect of improving the lift linear segment, delaying stall, and decreasing drag. Moreover, the maximum lift coefficient is approximately 0.19, and the lift-to-drag ratio increment in the control state with a 30° flap deflection angle is above 2.2 in the angle of attack range of 4° to 12° compared to the uncontrolled state with a 40° flap deflection angle.