Wanbo Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wanbo Wang has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Jiaxin Pan
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China
2 shared publications - Jiaxin Pan
Low Speed Aerodynamics Institute, China Aerodynamics Research and Development Center, Mianyang 621000, China
2 shared publications - Xinhai Zhao
China Aerodynamics Research and Development Center
2 shared publications - Xunnian Wang
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China
2 shared publications Chang Li
China Aerodynamics Research and Development Center
1 shared publication- Chaoqun Li
State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China
1 shared publication
Latest Publications
- 14 September 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1043, A17
The ‘step stall’ phenomenon of a supersonic Coanda jet
This study presents an experimental investigation into the influence of a step on the detachment characteristics of a supersonic Coanda jet. A parametric analysis was conducted by systematically varying the Coanda surface radius, jet outlet height and step height. Flow morphology was captured using high-speed schlieren and shadowgraph visualisation, while the critical nozzle pressure ratio ( italic NPR $\textit{NPR}$ ) for jet detachment was precisely measured with pressure transducers. For the baseline configuration without a step, the detachment italic NPR $\textit{NPR}$ (denoted italic NPR $\textit{NPR}$ d ) was predicted by a macroscopic mechanical model balancing centrifugal force and the radial pressure gradient, confirming a power-law relationship with the geometric ratio. The introduction of a step revealed a novel ‘step stall’ phenomenon: while increasing the step height initially enhances attachment and raises italic NPR $\textit{NPR}$ d by simplifying wave structures and suppressing separation bubbles, a further increase beyond a critical optimal value causes a sharp drop in performance. This optimal step height, which maximises the detachment italic NPR $\textit{NPR}$ , is shown to have a linear relationship with the normalised Coanda radius. The phenomenon is explained by the ineffective wall–jet interaction when an excessive step height prevents the jet’s core from being effectively ‘grabbed’ by the curved surface. These findings provide critical insights and practical design guidelines for optimising the Coanda effect in advanced flow control applications.- 14 September 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1043, A17
The ‘step stall’ phenomenon of a supersonic Coanda jet
This study presents an experimental investigation into the influence of a step on the detachment characteristics of a supersonic Coanda jet. A parametric analysis was conducted by systematically varying the Coanda surface radius, jet outlet height and step height. Flow morphology was captured using high-speed schlieren and shadowgraph visualisation, while the critical nozzle pressure ratio ( italic NPR $\textit{NPR}$ ) for jet detachment was precisely measured with pressure transducers. For the baseline configuration without a step, the detachment italic NPR $\textit{NPR}$ (denoted italic NPR $\textit{NPR}$ d ) was predicted by a macroscopic mechanical model balancing centrifugal force and the radial pressure gradient, confirming a power-law relationship with the geometric ratio. The introduction of a step revealed a novel ‘step stall’ phenomenon: while increasing the step height initially enhances attachment and raises italic NPR $\textit{NPR}$ d by simplifying wave structures and suppressing separation bubbles, a further increase beyond a critical optimal value causes a sharp drop in performance. This optimal step height, which maximises the detachment italic NPR $\textit{NPR}$ , is shown to have a linear relationship with the normalised Coanda radius. The phenomenon is explained by the ineffective wall–jet interaction when an excessive step height prevents the jet’s core from being effectively ‘grabbed’ by the curved surface. These findings provide critical insights and practical design guidelines for optimising the Coanda effect in advanced flow control applications.- 29 September 2025
- Published by Pleiades Publishing Ltd in Fluid Dynamics
- Vol. 60 (5) , 1-11
Experimental Study on the Enhancement of Blowing Lift of a Near-Wave Water Wing
The aerodynamic characteristics of amphibious aircraft in real wind and wave conditions are studied. An experimental investigation of jet lift control on airfoil in near-wave water is conducted. The novel wind-water tunnel testing methods are proposed. The study focuses on the aerodynamic performance of the basic airfoil, the lift enhancement performance of the jet, and ground/water surface effects. The results show that flap jet flow significantly increases the lift coefficient of the airfoil. When Cμ = 0.024, the lift increase is equal to approximately 48.3%. As compared to steady jet flow, unsteady pulsed jet flow has the greater lift enhancement potential, with a lift increase of about 32.5% at Cμ = 0.015. The dimensionless wave height A1 in the range from 0.653 to 0.928 results in a smoother stall characteristic compared to A1 = 0.307. The higher wave motion adversely affects the lift enhancement of the airfoil under jet control.
- 29 September 2025
- Published by Pleiades Publishing Ltd in Fluid Dynamics
- Vol. 60 (5) , 1-11
Experimental Study on the Enhancement of Blowing Lift of a Near-Wave Water Wing
The aerodynamic characteristics of amphibious aircraft in real wind and wave conditions are studied. An experimental investigation of jet lift control on airfoil in near-wave water is conducted. The novel wind-water tunnel testing methods are proposed. The study focuses on the aerodynamic performance of the basic airfoil, the lift enhancement performance of the jet, and ground/water surface effects. The results show that flap jet flow significantly increases the lift coefficient of the airfoil. When Cμ = 0.024, the lift increase is equal to approximately 48.3%. As compared to steady jet flow, unsteady pulsed jet flow has the greater lift enhancement potential, with a lift increase of about 32.5% at Cμ = 0.015. The dimensionless wave height A1 in the range from 0.653 to 0.928 results in a smoother stall characteristic compared to A1 = 0.307. The higher wave motion adversely affects the lift enhancement of the airfoil under jet control.
- 25 August 2025
- Published by Springer Nature in Experiments in Fluids
- Vol. 66 (9) , 1-15
Wall shear stress measurement by detecting viscous liquid surface deformation in a cavity in incompressible flow
- 25 August 2025
- Published by Springer Nature in Experiments in Fluids
- Vol. 66 (9) , 1-15
Wall shear stress measurement by detecting viscous liquid surface deformation in a cavity in incompressible flow
- Open Access
Design of High-Efficiency Jet Lift Enhancement for Flaps Under Propeller Slipstream Influence
Both propeller slipstream and flap jet flow can significantly increase the aircraft lift coefficient. To establish design principles for efficient lift enhancement via jet flow under the influence of slipstream, wind tunnel experiments are conducted on a wing with propeller slipstream and jet flow. Force measurements using a balance and flow field measurements using hot-wire anemometry are employed to investigate the effects of different jet flow distribution methods on lift enhancement. The results indicate that the coupling of slipstream and jet flow effects can significantly increase wing lift. The stronger the slipstream effect, the more pronounced the lift enhancement under the same momentum coefficient. At the same thrust coefficient, a higher momentum coefficient is required in the slipstream-affected region to suppress airflow separation. Under the same jet flow rate, increasing the momentum coefficient in the slipstream-affected region can significantly improve lift enhancement. At the thrust coefficient of 0.46 and the momentum coefficient of 0.1, the optimized jet flow distribution method achieved a 52.6% greater lift enhancement compared to the spanwise uniform jet flow distribution method.
Open AccessDesign of High-Efficiency Jet Lift Enhancement for Flaps Under Propeller Slipstream Influence
Both propeller slipstream and flap jet flow can significantly increase the aircraft lift coefficient. To establish design principles for efficient lift enhancement via jet flow under the influence of slipstream, wind tunnel experiments are conducted on a wing with propeller slipstream and jet flow. Force measurements using a balance and flow field measurements using hot-wire anemometry are employed to investigate the effects of different jet flow distribution methods on lift enhancement. The results indicate that the coupling of slipstream and jet flow effects can significantly increase wing lift. The stronger the slipstream effect, the more pronounced the lift enhancement under the same momentum coefficient. At the same thrust coefficient, a higher momentum coefficient is required in the slipstream-affected region to suppress airflow separation. Under the same jet flow rate, increasing the momentum coefficient in the slipstream-affected region can significantly improve lift enhancement. At the thrust coefficient of 0.46 and the momentum coefficient of 0.1, the optimized jet flow distribution method achieved a 52.6% greater lift enhancement compared to the spanwise uniform jet flow distribution method.
- Open Access
PCA-Kriging-Based Oscillating Jet Actuator Optimization and Wing Separation Flow Control
In order to improve the separation control effect of an oscillating jet, the external flow field of the actuators and the wing wake are obtained via hot-wire measurements to optimize the actuator and achieve wing separation flow control. The optimization objectives are to improve the sweeping uniformity and range of the jet. In the present study, the PCA method is used for the modal decomposition of the velocity distribution. The modal-based actuator evaluation parameters are proposed, and the kriging surrogate models of the modal coefficients (principal components) on the actuator parameters are established. The multi-objective genetic algorithm was utilized to complete the optimization of the actuator, and the effect of flow separation control on the wing was verified. The results show that three patterns exist in the time-averaged velocity distribution of the external flow field: unimodal, broad and bimodal, from unimodal to bimodal, the degree of the jet sweeping uniformity gradually decreases, and the sweeping range gradually increases. The pattern of the velocity distribution modals affects the degree of jet sweeping uniformity, while the distance of the modal peaks affects the jet sweeping range. The two evaluation parameters are negatively correlated: insufficient sweeping range or poor sweeping uniformity of the jet are not conducive to wing separation flow control, and the two must be coordinated to achieve the optimal control effect.
Open AccessPCA-Kriging-Based Oscillating Jet Actuator Optimization and Wing Separation Flow Control
In order to improve the separation control effect of an oscillating jet, the external flow field of the actuators and the wing wake are obtained via hot-wire measurements to optimize the actuator and achieve wing separation flow control. The optimization objectives are to improve the sweeping uniformity and range of the jet. In the present study, the PCA method is used for the modal decomposition of the velocity distribution. The modal-based actuator evaluation parameters are proposed, and the kriging surrogate models of the modal coefficients (principal components) on the actuator parameters are established. The multi-objective genetic algorithm was utilized to complete the optimization of the actuator, and the effect of flow separation control on the wing was verified. The results show that three patterns exist in the time-averaged velocity distribution of the external flow field: unimodal, broad and bimodal, from unimodal to bimodal, the degree of the jet sweeping uniformity gradually decreases, and the sweeping range gradually increases. The pattern of the velocity distribution modals affects the degree of jet sweeping uniformity, while the distance of the modal peaks affects the jet sweeping range. The two evaluation parameters are negatively correlated: insufficient sweeping range or poor sweeping uniformity of the jet are not conducive to wing separation flow control, and the two must be coordinated to achieve the optimal control effect.
- Open Access
Experimental Investigation on Flow Control over a Circular Cylinder Using Antiphase Pulsed Jets
To investigate the flow control characteristics of antiphase pulsed jet technology and explore a more efficient method to control unsteady flow with minimal impact on flow turbulence, wind tunnel experiments were conducted. The aim was to address the issue of flow separation control on the surface of a cylindrical model. The model had a diameter of 100 mm, and an experimental setup utilizing an antiphase pulsed jet excitation was developed. The optimisation of unsteady jet control involved adjusting parameters such as jet momentum coefficient, slot position, and excitation frequency. The flow separation control effect on the cylinder surface was compared between in-phase and antiphase pulsed jet using a particle image velocimetry (PIV) technique. The mechanisms of flow control for these two methods were analysed. The results showed that in still air, increasing the jet momentum led to a gradual decrease in the high-velocity region, which also moved away from the wall. Under incoming flow conditions, positioning the slot closer to the separation point resulted in better flow separation control, particularly when the excitation frequency matched the main flow frequency. Both in-phase and antiphase pulsed jet excitations effectively suppressed flow separation. In the near-wall region within the symmetric plane between the two slots, the antiphase excitation reduced the root mean square of velocity fluctuations by approximately 1.9% and increased the average velocity by approximately 15.5% compared to in-phase pulsed jet excitation. In-phase pulsed jets exhibited low-frequency, high-velocity characteristics near the separation point, while antiphase pulsed jets, due to the alternating discharge of the two jets, had a lesser impact on the flow field turbulence.
Open AccessExperimental Investigation on Flow Control over a Circular Cylinder Using Antiphase Pulsed Jets
To investigate the flow control characteristics of antiphase pulsed jet technology and explore a more efficient method to control unsteady flow with minimal impact on flow turbulence, wind tunnel experiments were conducted. The aim was to address the issue of flow separation control on the surface of a cylindrical model. The model had a diameter of 100 mm, and an experimental setup utilizing an antiphase pulsed jet excitation was developed. The optimisation of unsteady jet control involved adjusting parameters such as jet momentum coefficient, slot position, and excitation frequency. The flow separation control effect on the cylinder surface was compared between in-phase and antiphase pulsed jet using a particle image velocimetry (PIV) technique. The mechanisms of flow control for these two methods were analysed. The results showed that in still air, increasing the jet momentum led to a gradual decrease in the high-velocity region, which also moved away from the wall. Under incoming flow conditions, positioning the slot closer to the separation point resulted in better flow separation control, particularly when the excitation frequency matched the main flow frequency. Both in-phase and antiphase pulsed jet excitations effectively suppressed flow separation. In the near-wall region within the symmetric plane between the two slots, the antiphase excitation reduced the root mean square of velocity fluctuations by approximately 1.9% and increased the average velocity by approximately 15.5% compared to in-phase pulsed jet excitation. In-phase pulsed jets exhibited low-frequency, high-velocity characteristics near the separation point, while antiphase pulsed jets, due to the alternating discharge of the two jets, had a lesser impact on the flow field turbulence.
- Open Access
- 9 September 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (18) , 10166
Active Flow Control of a Supercritical Airfoil and Flap with Sweeping Jets
To provide sufficient lift during takeoff and landing, large aircraft are equipped with complicated high-lift devices. The use of simple flaps coupled with active flow control (AFC) can achieve lift improvement while reducing mechanical structure and weight. The present study focuses on verifying the feasibility and effectiveness of simple flaps combined with sweeping jet flow control. An experimental study on the AFC of flaps, using sweeping jets, was carried out using a NASA SC(2)-0410 supercritical airfoil wind-tunnel model at Re = 2.0 × 105 (with velocity V = 10 m/s). In the experiment, the wing angle of attack (α) ranged from 3 to 18°, and the flap deflection angle (δ) ranged from 0 to 30°; the aerodynamic characteristics and surface pressure characteristics of the wing at typical working conditions were analyzed. Using sweeping jets to control the flow on the flaps, the momentum coefficients (for three actuator groups) of the jet are 0.8%, 3.6%, and 8.2%, respectively, and the maximum lift coefficient was increased by approximately 33%. The influence of the sweeping jet flow rate on the aerodynamic performance of the airfoil is analyzed. There are two main reasons for the lift coefficient increase caused by sweeping jet flow: an extra suction peak near the flap and a suction peak increase near the leading edge area caused by induced flow.
- 9 September 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (18) , 10166
Open AccessActive Flow Control of a Supercritical Airfoil and Flap with Sweeping Jets
To provide sufficient lift during takeoff and landing, large aircraft are equipped with complicated high-lift devices. The use of simple flaps coupled with active flow control (AFC) can achieve lift improvement while reducing mechanical structure and weight. The present study focuses on verifying the feasibility and effectiveness of simple flaps combined with sweeping jet flow control. An experimental study on the AFC of flaps, using sweeping jets, was carried out using a NASA SC(2)-0410 supercritical airfoil wind-tunnel model at Re = 2.0 × 105 (with velocity V = 10 m/s). In the experiment, the wing angle of attack (α) ranged from 3 to 18°, and the flap deflection angle (δ) ranged from 0 to 30°; the aerodynamic characteristics and surface pressure characteristics of the wing at typical working conditions were analyzed. Using sweeping jets to control the flow on the flaps, the momentum coefficients (for three actuator groups) of the jet are 0.8%, 3.6%, and 8.2%, respectively, and the maximum lift coefficient was increased by approximately 33%. The influence of the sweeping jet flow rate on the aerodynamic performance of the airfoil is analyzed. There are two main reasons for the lift coefficient increase caused by sweeping jet flow: an extra suction peak near the flap and a suction peak increase near the leading edge area caused by induced flow.
- Open Access
Experimental Investigation on the Combined Blowing Control of a Hybrid Wing Body Aircraft
Combined blowing was performed on a Hybrid Wing Body (HWB) aircraft through wind tunnel testing at a Reynolds number of 1.75 × 106. The full cycle of separation and reattachment under the control of combined blowing was implemented using Computational Fluid Dynamics (CFD), and the mechanism of combined blowing inhibiting separation was analyzed. The aerodynamic characteristics of the baseline and the independent effects of the blown deflected trailing edge (TE), blown leading edge (LE), and combined blowing on the TE and LE were investigated. The results clearly show that combined blowing can inhibit the development of cross-flow, reduce the accumulation of a boundary layer at the tip, and inhibit the flow separation effect. The effect of using seamless simple flaps alone to increase the lift is limited; blowing control is required to enhance the lift further. Applying the blown deflected TE can improve the lift linear segment, so that 30° flap achieves the lift gain of 40° flap without control, while the drag coefficient is approximately 0.02 smaller, but the stall gradually advances. Using the blown LE can significantly increase the stall angle from 12° to 18°. However, the lift linear segment remains unaffected. In particular, combined blowing can achieve the control effect of improving the lift linear segment, delaying stall, and decreasing drag. Moreover, the maximum lift coefficient is approximately 0.19, and the lift-to-drag ratio increment in the control state with a 30° flap deflection angle is above 2.2 in the angle of attack range of 4° to 12° compared to the uncontrolled state with a 40° flap deflection angle.
Open AccessExperimental Investigation on the Combined Blowing Control of a Hybrid Wing Body Aircraft
Combined blowing was performed on a Hybrid Wing Body (HWB) aircraft through wind tunnel testing at a Reynolds number of 1.75 × 106. The full cycle of separation and reattachment under the control of combined blowing was implemented using Computational Fluid Dynamics (CFD), and the mechanism of combined blowing inhibiting separation was analyzed. The aerodynamic characteristics of the baseline and the independent effects of the blown deflected trailing edge (TE), blown leading edge (LE), and combined blowing on the TE and LE were investigated. The results clearly show that combined blowing can inhibit the development of cross-flow, reduce the accumulation of a boundary layer at the tip, and inhibit the flow separation effect. The effect of using seamless simple flaps alone to increase the lift is limited; blowing control is required to enhance the lift further. Applying the blown deflected TE can improve the lift linear segment, so that 30° flap achieves the lift gain of 40° flap without control, while the drag coefficient is approximately 0.02 smaller, but the stall gradually advances. Using the blown LE can significantly increase the stall angle from 12° to 18°. However, the lift linear segment remains unaffected. In particular, combined blowing can achieve the control effect of improving the lift linear segment, delaying stall, and decreasing drag. Moreover, the maximum lift coefficient is approximately 0.19, and the lift-to-drag ratio increment in the control state with a 30° flap deflection angle is above 2.2 in the angle of attack range of 4° to 12° compared to the uncontrolled state with a 40° flap deflection angle.