Moktarul Alam
Moktarul Alam has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Mohsen Koohestani
Ecole Suprieure dElectronique de lOuest, Angers, France
4 shared publications - Mohamed Ramdani
Cole Suprieure dlectronique de lOuest (ESEO), Angers, France
3 shared publications - Richard Perdriau
Cole Suprieure dlectronique de lOuest (ESEO), Angers, France
3 shared publications - Elfatih Abdelrahman Ahmed Elsheikh
Department of Electrical Engineering, College of Engineering, King Khalid University, Abha 61421, Saudi Arabia
1 shared publication - Philippe Besnier
Univ Rennes
1 shared publication - Rafiqul Islam
Department of Electrical and Computer Engineering, Faculty of Engineering, International Islamic University Malaysia, Kuala Lumpur, Malaysia
1 shared publication
Latest Publications
- 9 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Distributed Source-to-Source Co-Simulation Methodology Based on Waveform Relaxation Techniques and Time Windowing
Méthodologie de co-simulation distribuée source-à-source basée sur des techniques de relaxation de forme d’Onde et de fenêtrage temporel: Cette thèse présente une méthode de co-simulation efficace en ressources de calcul pour les convertisseurs continu-continu en boucle fermée, utilisant la relaxation de forme d’onde (WR) avec fenêtrage temporel. En divisant le système en deux sous-systèmes (le convertisseur et le contrôleur proportionnel-intégral – PI), cette approche améliore la précision de la simulation et garantit un échange sécurisé de données entre des sous-systèmes développés indépendamment, tout en prenant en compte le comportement non linéaire des systèmes électroniques de puissance.Un modèle analytique est également développé pour déterminer le nombre optimal de fenêtres temporelles en fonction de la taille de la fenêtre et des paramètres de simulation, afin de réduire le temps de calcul tout en conservant la même précision. Un algorithme génétique (AG) est utilisé pour optimiser les paramètres de relaxation, en traitant les comportements non linéaires des dispositifs lors d’une simulation circuit-à-circuit sans boucle de contre-réaction.La méthode proposée réduit ainsi efficacement l’erreur entre les résultats de sortie de la co-simulation et ceux de la simulation du système complet (utilisés uniquement pour la validation), améliorant ainsi la rapidité et la précision des simulations dans les applications d’électronique de puissance.
- 9 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Distributed Source-to-Source Co-Simulation Methodology Based on Waveform Relaxation Techniques and Time Windowing
Méthodologie de co-simulation distribuée source-à-source basée sur des techniques de relaxation de forme d’Onde et de fenêtrage temporel: Cette thèse présente une méthode de co-simulation efficace en ressources de calcul pour les convertisseurs continu-continu en boucle fermée, utilisant la relaxation de forme d’onde (WR) avec fenêtrage temporel. En divisant le système en deux sous-systèmes (le convertisseur et le contrôleur proportionnel-intégral – PI), cette approche améliore la précision de la simulation et garantit un échange sécurisé de données entre des sous-systèmes développés indépendamment, tout en prenant en compte le comportement non linéaire des systèmes électroniques de puissance.Un modèle analytique est également développé pour déterminer le nombre optimal de fenêtres temporelles en fonction de la taille de la fenêtre et des paramètres de simulation, afin de réduire le temps de calcul tout en conservant la même précision. Un algorithme génétique (AG) est utilisé pour optimiser les paramètres de relaxation, en traitant les comportements non linéaires des dispositifs lors d’une simulation circuit-à-circuit sans boucle de contre-réaction.La méthode proposée réduit ainsi efficacement l’erreur entre les résultats de sortie de la co-simulation et ceux de la simulation du système complet (utilisés uniquement pour la validation), améliorant ainsi la rapidité et la précision des simulations dans les applications d’électronique de puissance.
- Open Access
- 24 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Industry Applications
- Vol. 6, 852-866
Optimization of Time Windowing Technique for Closed-Loop Circuit Cosimulation Using WR Method
Power electronic systems are widely used for efficient power processing across various applications. However, due to their nonlinear behavior and susceptibility to disturbances, modeling and simulation are essential for fully understanding their complex interactions. The waveform relaxation (WR) method is employed to solve subsystems independently, with data exchanged until convergence is reached, offering flexibility in selecting solvers and integration techniques. In power electronics, applying the WR method with time windowing improves simulation stability and accuracy by introducing an equation to determine the optimal number of time windows. A time windowing technique is proposed, for the first time, for the co-simulation of a closed-loop power circuit divided into a first subsystem (converter) and a second subsystem (Proportional-Integral controller). These two subsystems are supposed to be designed by two different entities, which are not allowed to exchange their respective models for intellectual property reasons. The time windowing WR method is applied to transfer the data from subsystem 1 to 2. More importantly, an analytical model for the implementation of a time windowing WR technique is developed. This equation allows a deterministic choice of the number of time windows at each iteration, for convergence, based on windowing size and simulation parameters. Results show consistent output within a specified voltage range, with reduced CPU simulation time compared to co-simulation with an arbitrary selection of numbers of time windows, while being comparable to the full system simulation. The proposed technique is implemented with an input voltage range of 1.8-3 $V$, resulting in consistent outputs of 3.3 $V$ in both continuous- and discrete-time simulation modes. The comparative analysis demonstrates that with an increased number of iterations, the elapsed time is 11.1% and 5.6% faster for continuous- and discrete-time simulation modes, respectively, compared to a co-simulation with time windows. Furthermore, the time windowing WR method closely aligns with the full system result, with only a slight difference in elapsed time. Additionally, to validate the proposed analytical model using the time windowing WR technique in a closed-loop circuit, the buck converter is evaluated and compared without the full system. These results highlight the accuracy of WR with time windowing method and illustrate the quicker convergence achieved when used in circuit co-simulation.
- 24 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Industry Applications
- Vol. 6, 852-866
Open AccessOptimization of Time Windowing Technique for Closed-Loop Circuit Cosimulation Using WR Method
Power electronic systems are widely used for efficient power processing across various applications. However, due to their nonlinear behavior and susceptibility to disturbances, modeling and simulation are essential for fully understanding their complex interactions. The waveform relaxation (WR) method is employed to solve subsystems independently, with data exchanged until convergence is reached, offering flexibility in selecting solvers and integration techniques. In power electronics, applying the WR method with time windowing improves simulation stability and accuracy by introducing an equation to determine the optimal number of time windows. A time windowing technique is proposed, for the first time, for the co-simulation of a closed-loop power circuit divided into a first subsystem (converter) and a second subsystem (Proportional-Integral controller). These two subsystems are supposed to be designed by two different entities, which are not allowed to exchange their respective models for intellectual property reasons. The time windowing WR method is applied to transfer the data from subsystem 1 to 2. More importantly, an analytical model for the implementation of a time windowing WR technique is developed. This equation allows a deterministic choice of the number of time windows at each iteration, for convergence, based on windowing size and simulation parameters. Results show consistent output within a specified voltage range, with reduced CPU simulation time compared to co-simulation with an arbitrary selection of numbers of time windows, while being comparable to the full system simulation. The proposed technique is implemented with an input voltage range of 1.8-3 $V$, resulting in consistent outputs of 3.3 $V$ in both continuous- and discrete-time simulation modes. The comparative analysis demonstrates that with an increased number of iterations, the elapsed time is 11.1% and 5.6% faster for continuous- and discrete-time simulation modes, respectively, compared to a co-simulation with time windows. Furthermore, the time windowing WR method closely aligns with the full system result, with only a slight difference in elapsed time. Additionally, to validate the proposed analytical model using the time windowing WR technique in a closed-loop circuit, the buck converter is evaluated and compared without the full system. These results highlight the accuracy of WR with time windowing method and illustrate the quicker convergence achieved when used in circuit co-simulation.
- Open Access
- 7 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 80775-80785
Relaxation Parameter Optimization in Electrical-to-Mechanical Co-Simulation Based on Time Windowing WR Technique
This paper presents an innovative approach to enhancing the time windowing waveform relaxation (WR) technique in electrical-to-mechanical co-simulation by optimizing relaxation parameters for improved performance. An analytical model is introduced to determine the optimal number of time windows, considering the circuit’s dynamic characteristics. Additionally, a genetic algorithm (GA) is applied to refine relaxation parameters (e.g., impedance values), effectively addressing challenges posed by nonlinear device behaviors and improving the accuracy of co-simulation results. In the case study, it is crucial to emphasize that the full system simulation is used exclusively for retrospective validation of the co-simulation, without incorporating its results as inputs or convergence criteria. The proposed method significantly reduces the average error between co-simulation results and the full system output voltage, decreasing it from -2.8 dB to less than -26.2 dB. This demonstrates improved alignment and faster convergence compared to using theWRmethod. The validation of GA method is then applied to the co-simulation of an electrical (buck converter) and mechanical (DC motor) system, with results compared against the full system. The WR method exhibited significantly lower power efficiency (57.4%) compared to the full system (81.4%), rendering it insufficient. Time windowing WR enhanced power efficiency through simulation segmentation, reaching 74.6%, though it still fell short of the full system. The most advanced approach, time windowing WR with GA optimization, dynamically adjusted relaxation parameters, resulting in a power efficiency of 80.8%, nearly matching the 81.4% recorded in the single-kernel simulation. These findings underscore the effectiveness of integrating time segmentation with adaptive optimization to enhance simulation performance.
- 7 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 80775-80785
Open AccessRelaxation Parameter Optimization in Electrical-to-Mechanical Co-Simulation Based on Time Windowing WR Technique
This paper presents an innovative approach to enhancing the time windowing waveform relaxation (WR) technique in electrical-to-mechanical co-simulation by optimizing relaxation parameters for improved performance. An analytical model is introduced to determine the optimal number of time windows, considering the circuit’s dynamic characteristics. Additionally, a genetic algorithm (GA) is applied to refine relaxation parameters (e.g., impedance values), effectively addressing challenges posed by nonlinear device behaviors and improving the accuracy of co-simulation results. In the case study, it is crucial to emphasize that the full system simulation is used exclusively for retrospective validation of the co-simulation, without incorporating its results as inputs or convergence criteria. The proposed method significantly reduces the average error between co-simulation results and the full system output voltage, decreasing it from -2.8 dB to less than -26.2 dB. This demonstrates improved alignment and faster convergence compared to using theWRmethod. The validation of GA method is then applied to the co-simulation of an electrical (buck converter) and mechanical (DC motor) system, with results compared against the full system. The WR method exhibited significantly lower power efficiency (57.4%) compared to the full system (81.4%), rendering it insufficient. Time windowing WR enhanced power efficiency through simulation segmentation, reaching 74.6%, though it still fell short of the full system. The most advanced approach, time windowing WR with GA optimization, dynamically adjusted relaxation parameters, resulting in a power efficiency of 80.8%, nearly matching the 81.4% recorded in the single-kernel simulation. These findings underscore the effectiveness of integrating time segmentation with adaptive optimization to enhance simulation performance.
- 12 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (6) , 8553-8565
Circuit-to-Circuit Cosimulation for Closed-Loop Electrical Systems Using Waveform Relaxation
A computational time saving approach is proposed for the cosimulation of a buck–boost converter using waveform relaxation (WR) and time windowing. This study implements the Gauss–Seidel (GS) method, an iterative process that is employed to solve systems of linear and nonlinear equations using the WR technique, improving the convergence speed and accuracy of closed-loop system dynamic simulations. The proposed technique is applied to a 3.3-V buck–boost converter working both in buck and boost modes, therefore, simulations and measurements are carried out with a 1.8- to 5.5-V input voltage range. A comparative analysis between GS-WR without and with time windowing demonstrates that with time windowing, the number of iterations increases by 60$\%$ and 67.8$\%$, while the elapsed time is reduced by 22.3$\%$ and 26.6$\%$ with respect to a single time windows in buck and boost modes, respectively. Moreover, the optimal number of time windows (i.e., 4), computed by simulation, yields a 8.1$\%$ and 18.1$\%$ faster simulation time compared to the highest considered value in the study (i.e., 10). The outcome of this comparison reveals that a higher number of time windows does not necessarily result in a quicker computation compared to a lower value. More specifically, the GS-WR technique was found to be the main contributor to the acceleration, while time windowing ensures the convergence to the same results as the full system simulation.
- 12 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (6) , 8553-8565
Circuit-to-Circuit Cosimulation for Closed-Loop Electrical Systems Using Waveform Relaxation
A computational time saving approach is proposed for the cosimulation of a buck–boost converter using waveform relaxation (WR) and time windowing. This study implements the Gauss–Seidel (GS) method, an iterative process that is employed to solve systems of linear and nonlinear equations using the WR technique, improving the convergence speed and accuracy of closed-loop system dynamic simulations. The proposed technique is applied to a 3.3-V buck–boost converter working both in buck and boost modes, therefore, simulations and measurements are carried out with a 1.8- to 5.5-V input voltage range. A comparative analysis between GS-WR without and with time windowing demonstrates that with time windowing, the number of iterations increases by 60$\%$ and 67.8$\%$, while the elapsed time is reduced by 22.3$\%$ and 26.6$\%$ with respect to a single time windows in buck and boost modes, respectively. Moreover, the optimal number of time windows (i.e., 4), computed by simulation, yields a 8.1$\%$ and 18.1$\%$ faster simulation time compared to the highest considered value in the study (i.e., 10). The outcome of this comparison reveals that a higher number of time windows does not necessarily result in a quicker computation compared to a lower value. More specifically, the GS-WR technique was found to be the main contributor to the acceleration, while time windowing ensures the convergence to the same results as the full system simulation.
- Open Access
- 28 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 53588-53597
Prediction of Time Diversity Gain for Earth-to-Satellite Microwave Link Design Based on Real Time Rain Intensity Measurement
The propagation impairments by rain strongly affect the earth-to-satellite links operating at frequencies higher than 18 GHz mainly due to the severe performance degradation of satellite communication system. The time diversity technique with appropriate time delay between successive transmissions has been found effective in mitigating the rain fade. However, time diversity analysis demands measured rain attenuation data, where the latter is unavailable at most of the places to be able to design future high frequency links. The time diversity gain prediction model has been found to be robust for time diversity improvement. Here, we propose a new model for the rain rate with and without the time delay considering the three variables of rain rate, time delay and frequency. The rain rate and time delay functions were first used to derive the constants by the regression from the rain rate and rain rate gain. The constant for the frequency function was then extracted from the cumulative distribution function of the attenuation predicted by the analytically obtained ITU-R and gain equations. The proposed model was validated using one-year rain rate and attenuation data measured at two different locations in Malaysia demonstrating a 7% prediction inaccuracy when compared to the existing models, therefore, it can be reliably used for future earth-to-satellite link designs by using measured rain rate at any higher frequencies.
- 28 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 53588-53597
Open AccessPrediction of Time Diversity Gain for Earth-to-Satellite Microwave Link Design Based on Real Time Rain Intensity Measurement
The propagation impairments by rain strongly affect the earth-to-satellite links operating at frequencies higher than 18 GHz mainly due to the severe performance degradation of satellite communication system. The time diversity technique with appropriate time delay between successive transmissions has been found effective in mitigating the rain fade. However, time diversity analysis demands measured rain attenuation data, where the latter is unavailable at most of the places to be able to design future high frequency links. The time diversity gain prediction model has been found to be robust for time diversity improvement. Here, we propose a new model for the rain rate with and without the time delay considering the three variables of rain rate, time delay and frequency. The rain rate and time delay functions were first used to derive the constants by the regression from the rain rate and rain rate gain. The constant for the frequency function was then extracted from the cumulative distribution function of the attenuation predicted by the analytically obtained ITU-R and gain equations. The proposed model was validated using one-year rain rate and attenuation data measured at two different locations in Malaysia demonstrating a 7% prediction inaccuracy when compared to the existing models, therefore, it can be reliably used for future earth-to-satellite link designs by using measured rain rate at any higher frequencies.