Jun Long
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jun Long has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Yuedong Xie
Key Laboratory of Precision Opto-mechatronics Technology of Education Ministry, School of Instrumentation and Opto-Electronic Engineering, Beihang University, Beijing, China
5 shared publications - Lijun Xu
Beihang University
4 shared publications - Fulu Liu
School of Instrumentation and Optoelectronic Engineering, Beihang University, Beijing, China
3 shared publications - Zhiying Li
School of Instrumentation and Opto-electronic Engineering, Beihang University, Beijing, China
3 shared publications - Jiyao Li
Beihang University
2 shared publications - Linhui Ma
School of Instrument and Optoelectronic Engineering, Beihang University, Beijing, China
2 shared publications
Latest Publications
- 9 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-9
An EMAT Guided Wave Tomography System for Gas–Liquid Two-Phase Flow Imaging
The gas-liquid two-phase flow tomography technique has significant value for industrial process monitoring. However, the harsh environment and metal pipes present a challenge that limits the applicability of existing techniques. To address the challenge of gas-liquid two-phase flow tomography in metal pipes, an ultrasonic tomography (UT) system based on electromagnetic acoustic transducer (EMAT) technology was designed and developed to effectively realize process tomography. By considering the installation distance, guided wave mode, and transducer coil proportion of the EMAT array, the optimal overall scheme of the EMAT array can be obtained through finite element (FE) simulation. Through experimental tests, the consistency of each channel of the EMAT array is evaluated and normalized in order to reduce the artefacts that are caused by channel inconsistency. In order to achieve tomography in metal pipes in static experiments, a revised total focusing method (TFM) algorithm has been developed within the UT system, utilising the EMAT guided wave. The analysis of the imaging effect and the sensitivity distribution in the imaging region has led to the formulation of proposals regarding the limitations of the system and potential improvement methods.
- 9 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-9
An EMAT Guided Wave Tomography System for Gas–Liquid Two-Phase Flow Imaging
The gas-liquid two-phase flow tomography technique has significant value for industrial process monitoring. However, the harsh environment and metal pipes present a challenge that limits the applicability of existing techniques. To address the challenge of gas-liquid two-phase flow tomography in metal pipes, an ultrasonic tomography (UT) system based on electromagnetic acoustic transducer (EMAT) technology was designed and developed to effectively realize process tomography. By considering the installation distance, guided wave mode, and transducer coil proportion of the EMAT array, the optimal overall scheme of the EMAT array can be obtained through finite element (FE) simulation. Through experimental tests, the consistency of each channel of the EMAT array is evaluated and normalized in order to reduce the artefacts that are caused by channel inconsistency. In order to achieve tomography in metal pipes in static experiments, a revised total focusing method (TFM) algorithm has been developed within the UT system, utilising the EMAT guided wave. The analysis of the imaging effect and the sensitivity distribution in the imaging region has led to the formulation of proposals regarding the limitations of the system and potential improvement methods.
- 15 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-12
A Defects Detection Method of Buried Liquid-Filled Pipes Based on T(0,1) Guided Waves
In this paper, we propose a method using T(0,1) guided waves combined with coil coding technique to detect defects in buried liquid-filled pipes implemented by an electromagnetic acoustic transducer (EMAT). Due to its non-dispersive properties and the fact that there is no energy loss in non-viscoelastic fluids, the T(0,1) mode is selected for pipe defects detection. The electromagnetic device that generates the circumferential magnetic field is optimized to excite the pure T(0,1) mode. To realize energy enhancement and defect location identification, the electromagnetic acoustic coil is spatially encoded by 11-bit Barker code and the receiver coil is multiplexed consisting of a spatial coded coil and a unit coil. The defect detection is accomplished through time-of-flight (TOF) time-frequency analysis, and the defect location identification is achieved by digital signal processing methods (cross-correlation and convolution). The feasibility of this method is verified by the finite element model and experimental analysis, indicating the defect locating error in a liquid-filled pipes is less than 1%. Overall, the proposed method achieves a high-precision flaw detection and location identification.
- 15 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-12
A Defects Detection Method of Buried Liquid-Filled Pipes Based on T(0,1) Guided Waves
In this paper, we propose a method using T(0,1) guided waves combined with coil coding technique to detect defects in buried liquid-filled pipes implemented by an electromagnetic acoustic transducer (EMAT). Due to its non-dispersive properties and the fact that there is no energy loss in non-viscoelastic fluids, the T(0,1) mode is selected for pipe defects detection. The electromagnetic device that generates the circumferential magnetic field is optimized to excite the pure T(0,1) mode. To realize energy enhancement and defect location identification, the electromagnetic acoustic coil is spatially encoded by 11-bit Barker code and the receiver coil is multiplexed consisting of a spatial coded coil and a unit coil. The defect detection is accomplished through time-of-flight (TOF) time-frequency analysis, and the defect location identification is achieved by digital signal processing methods (cross-correlation and convolution). The feasibility of this method is verified by the finite element model and experimental analysis, indicating the defect locating error in a liquid-filled pipes is less than 1%. Overall, the proposed method achieves a high-precision flaw detection and location identification.
- 13 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-10
A Novel Noncontact Method for Phase Interface Measurement in Liquid-Filled Pipe Using Leaky L(0,2) Wave
In this paper, we propose a novel phase interface measurement method in the liquid-filled pipe using leaky L(0,2) wave implemented by an electromagnetic acoustic transducer (EMAT). Two EMATs with flexible coils are circumferentially wrapped on the liquid-filled pipe, acting as exciting EMAT and receiving EMAT respectively. The coil used in the excitation EMAT is a ten-turn meander-line-coil exited with a five-cycle Hanning windowed tone burst signal to produce pure leaky L(0,2) waves. The feasibility of this method has been verified by finite element model and experimental analysis. During experiments, the liquid levels in the vertical pipe and horizontal pipe can be obtained by means of the amplitude of the received L(0,2) wave. Various diameters of the rod were used to model different phase interfaces and the results indicate the diameter is linear to the arrival time of the leaking L(0,2) wave. Meanwhile, the amplitude of the leaky L(0,2) signal in a certain range is used to express the reflectivity of the phase interface. Based on these results, the proposed method can be used for phase interface measurement, and provides a potential of phase interface imaging.
- 13 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-10
A Novel Noncontact Method for Phase Interface Measurement in Liquid-Filled Pipe Using Leaky L(0,2) Wave
In this paper, we propose a novel phase interface measurement method in the liquid-filled pipe using leaky L(0,2) wave implemented by an electromagnetic acoustic transducer (EMAT). Two EMATs with flexible coils are circumferentially wrapped on the liquid-filled pipe, acting as exciting EMAT and receiving EMAT respectively. The coil used in the excitation EMAT is a ten-turn meander-line-coil exited with a five-cycle Hanning windowed tone burst signal to produce pure leaky L(0,2) waves. The feasibility of this method has been verified by finite element model and experimental analysis. During experiments, the liquid levels in the vertical pipe and horizontal pipe can be obtained by means of the amplitude of the received L(0,2) wave. Various diameters of the rod were used to model different phase interfaces and the results indicate the diameter is linear to the arrival time of the leaking L(0,2) wave. Meanwhile, the amplitude of the leaky L(0,2) signal in a certain range is used to express the reflectivity of the phase interface. Based on these results, the proposed method can be used for phase interface measurement, and provides a potential of phase interface imaging.
- 26 August 2023
- Published by Elsevier in Measurement
- Vol. 221
Measurement of conductivity and diameter of metallic rods using eddy current testing
- 26 August 2023
- Published by Elsevier in Measurement
- Vol. 221
Measurement of conductivity and diameter of metallic rods using eddy current testing
- 14 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-10
Measurement of Lift-Off Distance and Thickness of Nonmagnetic Metallic Plate Using Pulsed Eddy Current Testing
Eddy current testing (ECT) is an efficient method to estimate the thickness of sample but it is affected by other parameters information including electromagnetic properties and lift-off. In the previous researches, the lift-off point of intersection (LOI) feature has been found in pulsed eddy current (PEC), which can overcome the fluctuation of lift-off. In this paper, another feature, i.e. conductivity point of intersection(CPI), is proposed for non-coaxial T-R sensor in PEC. Specifically, the response signals of different sample conductivity almost intersect with each other at the certain time, which can be regarded immune to the conductivity of sample. The analytical solution and numerical solution are conducted, and the results indicate that the intersection point magnitude is mainly related with parameters of sensor and thickness of samples. Considering the elements related with conductivity in the Hessian matrix exists ill-conditioning, it will produce the magnification of measurement error under iterative inversion process. By referring to the CPI feature, the thickness of the sample and lift-off of sensor can be accurately inverted based on the modified Newton–Raphson method. The experiments are carried out to verify the proposed method, and the error is only 2.9%.
- 14 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-10
Measurement of Lift-Off Distance and Thickness of Nonmagnetic Metallic Plate Using Pulsed Eddy Current Testing
Eddy current testing (ECT) is an efficient method to estimate the thickness of sample but it is affected by other parameters information including electromagnetic properties and lift-off. In the previous researches, the lift-off point of intersection (LOI) feature has been found in pulsed eddy current (PEC), which can overcome the fluctuation of lift-off. In this paper, another feature, i.e. conductivity point of intersection(CPI), is proposed for non-coaxial T-R sensor in PEC. Specifically, the response signals of different sample conductivity almost intersect with each other at the certain time, which can be regarded immune to the conductivity of sample. The analytical solution and numerical solution are conducted, and the results indicate that the intersection point magnitude is mainly related with parameters of sensor and thickness of samples. Considering the elements related with conductivity in the Hessian matrix exists ill-conditioning, it will produce the magnification of measurement error under iterative inversion process. By referring to the CPI feature, the thickness of the sample and lift-off of sensor can be accurately inverted based on the modified Newton–Raphson method. The experiments are carried out to verify the proposed method, and the error is only 2.9%.