Rui Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rui Yang has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Yi Xie
College of Mechanical and Vehicle Engineering, Chongqing University, Chongqing, China
8 shared publications - Yangjun Zhang
State Key Laboratory of Automotive Safety and Energy, Tsinghua University, Beijing, China
6 shared publications - Kuining Li
Chongqing University, Ministry of Education
4 shared publications - Satyam Panchal
Department of Chemical Engineering, University of Waterloo, Waterloo, ON N2L 3G1, Canada
4 shared publications Bin Chen
Chongqing Vehicle Test and Research Institute Company Ltd., Chongqing, China
2 shared publications- Wei Li
Singapore Institute of Technology, Singapore, Singapore
2 shared publications
Latest Publications
- Open Access
- 17 June 2026
- Published by Elsevier in SSRN Electronic Journal
Physics-based Analysis of Battery Reliability and Safety Degradation Behavior
Lithium-ion batteries face complex multi-physics degradation couplings that significantly affect their reliability and safety over the entire lifecycle. This paper develops a fully coupled and simplified electrochemical-thermal-mechanical-degradation model using a polynomial approximation method. It achieves voltage mean relative error (MRE) below 2% and temperature root mean square error within 1 °C in a 50Ah prismatic NMC/graphite battery. The electrode state of health (SOH) parameters have been validated, with majority MRE less than 5%. Based on this model, the effects of different temperatures, currents, and depth-of-discharge cycling on the proposed five reliability and safety parameters are revealed, including solid electrolyte interface (SEI) resistance, amount of lithium plating, particle structural damage, capacity fade and thermal safety. The results show that the SEI resistance initially decreases with the number of cycles due to interface optimization during the early aging stage. Approximately 25% active material loss in the graphite anode is identified as a threshold for significant SOH degradation. Moreover, low temperature dominates lithium plating and mechanical degradation, high temperature drives SEI thickening, and deep discharge coupled with high‑rate charging causes severe capacity fade and thermal risk in later aging stages. Finally, a SOH-staged management method considering main degradation risk and thermal safety over the full lifecycle is proposed. This work provides a practical framework for full‑life‑cycle battery reliability and safety assessment.
- 17 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessPhysics-based Analysis of Battery Reliability and Safety Degradation Behavior
Lithium-ion batteries face complex multi-physics degradation couplings that significantly affect their reliability and safety over the entire lifecycle. This paper develops a fully coupled and simplified electrochemical-thermal-mechanical-degradation model using a polynomial approximation method. It achieves voltage mean relative error (MRE) below 2% and temperature root mean square error within 1 °C in a 50Ah prismatic NMC/graphite battery. The electrode state of health (SOH) parameters have been validated, with majority MRE less than 5%. Based on this model, the effects of different temperatures, currents, and depth-of-discharge cycling on the proposed five reliability and safety parameters are revealed, including solid electrolyte interface (SEI) resistance, amount of lithium plating, particle structural damage, capacity fade and thermal safety. The results show that the SEI resistance initially decreases with the number of cycles due to interface optimization during the early aging stage. Approximately 25% active material loss in the graphite anode is identified as a threshold for significant SOH degradation. Moreover, low temperature dominates lithium plating and mechanical degradation, high temperature drives SEI thickening, and deep discharge coupled with high‑rate charging causes severe capacity fade and thermal risk in later aging stages. Finally, a SOH-staged management method considering main degradation risk and thermal safety over the full lifecycle is proposed. This work provides a practical framework for full‑life‑cycle battery reliability and safety assessment.
- 26 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (2) , 3954-3966
An Online Coestimation Framework for Coupled Electrothermal-Aging Key State of Lithium-Ion Batteries
Online acquisition of accurate battery electrical, thermal, and aging states is crucial for monitoring and management of batteries, especially in cloud-edge collaboration. In this article, an online joint estimation method for state of charge (SOC), 3-D state of temperature distribution (SOTD), and state of health (SOH) of batteries based on an electrothermal-aging coupled model is proposed. First, three well-chosen charging durations are leveraged as the aging features to achieve SOH estimation with the assistance of the extreme learning machine (ELM). Second, the state of temperature (SOT) is estimated through a lumped parameter thermal model (LPTM) and adaptive extended Kalman filter (KF) (AEKF), and SOTD is reconstructed using a well-designed fractal theory method (FTM) derived from the iterated function system (IFS) method and a Lindenmayer system (L-system), which ensures precise thermal state monitoring. Then, based on the parameter updating mechanism, the parameters of the equivalent circuit model (ECM) are adjusted in real time according to the accurate SOT and SOH, and the SOC is estimated by the AEKF. Subsequently, the proposed method is validated under different dynamic conditions and different temperatures, the validation results show that the proposed method can achieve accurate SOC–SOTD–SOH coestimation with an error of no more than 2.14%, $1.37~^{\circ }$ C, and 1.26%, respectively. Finally, the investigation of the SOT and SOH influence on SOC estimation reveals the important significance of the coestimation framework.
- 26 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (2) , 3954-3966
An Online Coestimation Framework for Coupled Electrothermal-Aging Key State of Lithium-Ion Batteries
Online acquisition of accurate battery electrical, thermal, and aging states is crucial for monitoring and management of batteries, especially in cloud-edge collaboration. In this article, an online joint estimation method for state of charge (SOC), 3-D state of temperature distribution (SOTD), and state of health (SOH) of batteries based on an electrothermal-aging coupled model is proposed. First, three well-chosen charging durations are leveraged as the aging features to achieve SOH estimation with the assistance of the extreme learning machine (ELM). Second, the state of temperature (SOT) is estimated through a lumped parameter thermal model (LPTM) and adaptive extended Kalman filter (KF) (AEKF), and SOTD is reconstructed using a well-designed fractal theory method (FTM) derived from the iterated function system (IFS) method and a Lindenmayer system (L-system), which ensures precise thermal state monitoring. Then, based on the parameter updating mechanism, the parameters of the equivalent circuit model (ECM) are adjusted in real time according to the accurate SOT and SOH, and the SOC is estimated by the AEKF. Subsequently, the proposed method is validated under different dynamic conditions and different temperatures, the validation results show that the proposed method can achieve accurate SOC–SOTD–SOH coestimation with an error of no more than 2.14%, $1.37~^{\circ }$ C, and 1.26%, respectively. Finally, the investigation of the SOT and SOH influence on SOC estimation reveals the important significance of the coestimation framework.
- 8 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. PP (02780046) , 1-10
A Holistic Electrothermal Profiles Online Sensing Method With Sparse Sensor System in Large-Format Battery Pack
With the promising advancements in lithium-ion battery technology, the management of large-scale battery packs is confronted with a significant challenge: while comprehensive, time-varying electrothermal profiles are essential, the sparse sensor system offers only limited sensing information. In emerging battery management systems, the lack of information in sensor systems is generally over-looked. This article proposes an optimization method for the architecture of battery sensor systems, enabling online sensing of global electrothermal profiles in large-scale battery packs. First, by expanding the application of information entropy, an architecture optimization method for an arbitrary battery sensor system is proposed. Building on this optimized sensor topology, the article then focuses on an online sensing method to capture global electrothermal profiles in large-scale battery packs. Through this approach, 3-D thermal profiles are derived using an enhanced fractal process, while global electrical parameters are updated in real time, accounting for thermal effects. Finally, this study shows that this article’s criteria for optimizing sensor topology can reveal more comprehensive characteristics of the global electrothermal field. The effectiveness of our methodology is validated by online sensing results of the electric and thermal profiles, achieving the error of less than 2% at the pack levels.
- 8 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. PP (02780046) , 1-10
A Holistic Electrothermal Profiles Online Sensing Method With Sparse Sensor System in Large-Format Battery Pack
With the promising advancements in lithium-ion battery technology, the management of large-scale battery packs is confronted with a significant challenge: while comprehensive, time-varying electrothermal profiles are essential, the sparse sensor system offers only limited sensing information. In emerging battery management systems, the lack of information in sensor systems is generally over-looked. This article proposes an optimization method for the architecture of battery sensor systems, enabling online sensing of global electrothermal profiles in large-scale battery packs. First, by expanding the application of information entropy, an architecture optimization method for an arbitrary battery sensor system is proposed. Building on this optimized sensor topology, the article then focuses on an online sensing method to capture global electrothermal profiles in large-scale battery packs. Through this approach, 3-D thermal profiles are derived using an enhanced fractal process, while global electrical parameters are updated in real time, accounting for thermal effects. Finally, this study shows that this article’s criteria for optimizing sensor topology can reveal more comprehensive characteristics of the global electrothermal field. The effectiveness of our methodology is validated by online sensing results of the electric and thermal profiles, achieving the error of less than 2% at the pack levels.
- 27 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 3980-3995
An Improved Velocity Planning Method for eVTOL Aircraft Based on Differential Evolution Algorithm Considering Flight Economy
This research establishes an energy management method for the velocity planning of an electric vertical takeoff and landing (eVTOL) aircraft to ensure and enhance flying safety and economy. This method integrates the aerodynamic and economic models of an aeroplane, power train model and battery electro-thermal-degradation model. It applies the differential evolution algorithm (DEA). Optimising the velocity profile and reducing the eVTOL aircraft’s power achieves a lower discharging rate and battery temperature, thus extending the battery lifespan and increasing profits over the battery lifetime. Compared with the original velocity profile, the optimised velocity extends the battery life by 41.7% and raises eVTOL aircraft profits by 1.8 times. Moreover, to obtain a suitable voltage platform and battery capacity for eVTOL aircrafts, the influence of the serial-connected cell number on the eVTOL aircraft’s performance is also investigated. According to the results, raising the battery voltage by increasing the cell number can reduce the discharging rate, temperature and capacity loss of the battery and increase the profits. However, numerous cells make an eVTOL aircraft overweight, rendering it unsuitable to take off. When the serial-connected cell number increases from 190 to 310, the battery lifespan is extended by 700 cycles, and the lifetime profit increases by 56,259.9 USD.
- 27 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 3980-3995
An Improved Velocity Planning Method for eVTOL Aircraft Based on Differential Evolution Algorithm Considering Flight Economy
This research establishes an energy management method for the velocity planning of an electric vertical takeoff and landing (eVTOL) aircraft to ensure and enhance flying safety and economy. This method integrates the aerodynamic and economic models of an aeroplane, power train model and battery electro-thermal-degradation model. It applies the differential evolution algorithm (DEA). Optimising the velocity profile and reducing the eVTOL aircraft’s power achieves a lower discharging rate and battery temperature, thus extending the battery lifespan and increasing profits over the battery lifetime. Compared with the original velocity profile, the optimised velocity extends the battery life by 41.7% and raises eVTOL aircraft profits by 1.8 times. Moreover, to obtain a suitable voltage platform and battery capacity for eVTOL aircrafts, the influence of the serial-connected cell number on the eVTOL aircraft’s performance is also investigated. According to the results, raising the battery voltage by increasing the cell number can reduce the discharging rate, temperature and capacity loss of the battery and increase the profits. However, numerous cells make an eVTOL aircraft overweight, rendering it unsuitable to take off. When the serial-connected cell number increases from 190 to 310, the battery lifespan is extended by 700 cycles, and the lifetime profit increases by 56,259.9 USD.
- 11 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (4) , 8713-8727
Influence of Uncertainty of Thermal Conductivity on Prediction Accuracy of Thermal Model of Lithium-Ion Battery
This study employed the transient plane source method (TPS) to measure the battery’s thermal conductivity. The probe heated the battery and collected its temperature. Based on the measured temperature, the thermal conductivity was calculated. Then, this tested thermal conductivity is compared with the theoretical value to get the prediction error of the theoretical algorithm. For the 27 Ah battery, the relative error of thermal conductivity through material layer kx is 30.2%, while those of thermal conductivities along material layer ky and kz are 89.8%. Then, a three-dimensional thermal model based on the thermal network was established, and it applied the calculated and measured thermal conductivity to quickly predict battery temperature distribution at discharging rate from 1 C to 6 C. According to the results, the theoretical model for thermal conductivity should be used at a discharging rate below 3 C, or a great prediction error is produced. To further improve the prediction accuracy of battery temperature field at high discharging rates, the error set of the thermal conductivity was built, and the threshold of the error was explored. The relative error of kx should vary between 15% and -15% and those of ky and kz should be below -45%. Moreover, the prediction error of the battery temperature is small, as the relative errors of ky and kz increase from 15% to 90%.
- 11 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (4) , 8713-8727
Influence of Uncertainty of Thermal Conductivity on Prediction Accuracy of Thermal Model of Lithium-Ion Battery
This study employed the transient plane source method (TPS) to measure the battery’s thermal conductivity. The probe heated the battery and collected its temperature. Based on the measured temperature, the thermal conductivity was calculated. Then, this tested thermal conductivity is compared with the theoretical value to get the prediction error of the theoretical algorithm. For the 27 Ah battery, the relative error of thermal conductivity through material layer kx is 30.2%, while those of thermal conductivities along material layer ky and kz are 89.8%. Then, a three-dimensional thermal model based on the thermal network was established, and it applied the calculated and measured thermal conductivity to quickly predict battery temperature distribution at discharging rate from 1 C to 6 C. According to the results, the theoretical model for thermal conductivity should be used at a discharging rate below 3 C, or a great prediction error is produced. To further improve the prediction accuracy of battery temperature field at high discharging rates, the error set of the thermal conductivity was built, and the threshold of the error was explored. The relative error of kx should vary between 15% and -15% and those of ky and kz should be below -45%. Moreover, the prediction error of the battery temperature is small, as the relative errors of ky and kz increase from 15% to 90%.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 20 (2) , 2295-2306
A Health-Aware AC Heating Strategy With Lithium Plating Criterion for Batteries at Low Temperatures
Lithium-ion batteries are crucial power sources in many industries. When they are used at low temperatures, their performance decreases greatly. Thus, heating is required. This article proposes a health-aware heating strategy based on the ac current. The strategy combines the use of the electro-thermal model for predicting the temperature increment in the battery caused by the ac current and a diagnostic method for lithium plating based on the charging transfer impedance. To obtain an accurate electro-thermal model for ac heating, various equivalent circuit models (ECMs) are tested at pulses with different frequencies and amplitudes, and the second-order ECM with a constant phase element is found to obtain the smallest error. Then, the model and the lithium plating criterion are used to establish the boundary map of the lithium plating and voltage limitations. Based on the map, the optimal ac frequency and amplitude are selected for the heating strategy. Finally, an ac heating experiment is implemented to verify the strategy. The results show that the strategy not only increases the battery temperature at a maximum rate of 5.25 °C/min, but also achieves a capacity decrease of 0.3% in 80 heating cycles. Moreover, according to the battery disassembly results, there is no lithium plating on the electrode. These results prove that the proposed heating strategy can prevent lithium plating and achieve a high heating efficiency.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 20 (2) , 2295-2306
A Health-Aware AC Heating Strategy With Lithium Plating Criterion for Batteries at Low Temperatures
Lithium-ion batteries are crucial power sources in many industries. When they are used at low temperatures, their performance decreases greatly. Thus, heating is required. This article proposes a health-aware heating strategy based on the ac current. The strategy combines the use of the electro-thermal model for predicting the temperature increment in the battery caused by the ac current and a diagnostic method for lithium plating based on the charging transfer impedance. To obtain an accurate electro-thermal model for ac heating, various equivalent circuit models (ECMs) are tested at pulses with different frequencies and amplitudes, and the second-order ECM with a constant phase element is found to obtain the smallest error. Then, the model and the lithium plating criterion are used to establish the boundary map of the lithium plating and voltage limitations. Based on the map, the optimal ac frequency and amplitude are selected for the heating strategy. Finally, an ac heating experiment is implemented to verify the strategy. The results show that the strategy not only increases the battery temperature at a maximum rate of 5.25 °C/min, but also achieves a capacity decrease of 0.3% in 80 heating cycles. Moreover, according to the battery disassembly results, there is no lithium plating on the electrode. These results prove that the proposed heating strategy can prevent lithium plating and achieve a high heating efficiency.
- 27 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 1541-1557
Comparative Study on the Thermal Characteristics of Solid-State Lithium-Ion Batteries
Battery temperature greatly affects its electrical performance and safety. In this work, the thermal characteristics of a hybrid solid-liquid battery (referred to as solid-state battery) were systematically studied for the development of future battery thermal management systems (BTMS). The battery resistance characteristics were investigated by performing electrochemical impedance spectroscopy (EIS) measurements. Then, the extracted outcomes were connected with the heat generation and used to explain the trends of the battery thermal characteristics at different temperatures and current rates. Moreover, the resistance and thermal characteristics of the solid-state battery were compared to those of the traditional LiNiMnCoO2 (NMC) and LiFePO4 (LFP) batteries with similar capacity. According to the results, the solid-state battery has a bigger polarization resistance than the traditional batteries, because of the larger charge transfer impedance and impedance across the film evoked by the solid electrolyte. The higher resistance makes the solid-state battery generate more heat and achieve a higher temperature rise, and a BTMS with stronger cooling performance is required. Moreover, the battery temperature rise plateau of the solid-state battery is mainly affected by the reversible heat, and the polarization heat is the biggest contributor to the total heat generation in the solid-state battery.
- 27 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 1541-1557
Comparative Study on the Thermal Characteristics of Solid-State Lithium-Ion Batteries
Battery temperature greatly affects its electrical performance and safety. In this work, the thermal characteristics of a hybrid solid-liquid battery (referred to as solid-state battery) were systematically studied for the development of future battery thermal management systems (BTMS). The battery resistance characteristics were investigated by performing electrochemical impedance spectroscopy (EIS) measurements. Then, the extracted outcomes were connected with the heat generation and used to explain the trends of the battery thermal characteristics at different temperatures and current rates. Moreover, the resistance and thermal characteristics of the solid-state battery were compared to those of the traditional LiNiMnCoO2 (NMC) and LiFePO4 (LFP) batteries with similar capacity. According to the results, the solid-state battery has a bigger polarization resistance than the traditional batteries, because of the larger charge transfer impedance and impedance across the film evoked by the solid electrolyte. The higher resistance makes the solid-state battery generate more heat and achieve a higher temperature rise, and a BTMS with stronger cooling performance is required. Moreover, the battery temperature rise plateau of the solid-state battery is mainly affected by the reversible heat, and the polarization heat is the biggest contributor to the total heat generation in the solid-state battery.
- 17 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 720-734
An Enhanced Electro-Thermal Coupled Model With Lithium Plating Detection for Lithium-Ion Battery at Low Temperatures
Lithium plating may occur when lithium-ion batteries are charged at a high current rate and low ambient temperature. As a result, the battery degradation is accelerated and the risk of thermal runaway is increased. Along these lines, an enhanced electro-thermal model was proposed in this work for charging at low temperature values. By considering the battery with a reference electrode, a dual RC model was built. The developed model can predict the anode potential to prevent the lithium plating. The thermal model and absolute state of charge (SOC) were integrated into the battery model to solve the SOC inconsistency caused by the battery temperature rise during the charging process. Then, the proposed electro-thermal model was used to predict the electrical and thermal characteristics of a 50 Ah battery under various charging rates and low ambient temperature values conditions. In addition, the prediction results were validated by the experiment data. The maximum errors of the cathode potential and battery terminal voltage were 0.058 V and 0.154 V, respectively, whereas the maximum cell temperature error was 0.88 °C. Based on the anode prediction electro-thermal coupling model, a segmented heating strategy without lithium plating was proposed to describe the fast battery charging procedure, which can reduce energy consumption by 16.1% and save charging time by nearly 10 minutes compared with the continuous high-power heating mode.
- 17 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 720-734
An Enhanced Electro-Thermal Coupled Model With Lithium Plating Detection for Lithium-Ion Battery at Low Temperatures
Lithium plating may occur when lithium-ion batteries are charged at a high current rate and low ambient temperature. As a result, the battery degradation is accelerated and the risk of thermal runaway is increased. Along these lines, an enhanced electro-thermal model was proposed in this work for charging at low temperature values. By considering the battery with a reference electrode, a dual RC model was built. The developed model can predict the anode potential to prevent the lithium plating. The thermal model and absolute state of charge (SOC) were integrated into the battery model to solve the SOC inconsistency caused by the battery temperature rise during the charging process. Then, the proposed electro-thermal model was used to predict the electrical and thermal characteristics of a 50 Ah battery under various charging rates and low ambient temperature values conditions. In addition, the prediction results were validated by the experiment data. The maximum errors of the cathode potential and battery terminal voltage were 0.058 V and 0.154 V, respectively, whereas the maximum cell temperature error was 0.88 °C. Based on the anode prediction electro-thermal coupling model, a segmented heating strategy without lithium plating was proposed to describe the fast battery charging procedure, which can reduce energy consumption by 16.1% and save charging time by nearly 10 minutes compared with the continuous high-power heating mode.