Peicong Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Peicong Chen has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Lei Ge
Shenzhen University
3 shared publications - Qing-Yi Guo
Department of Electrical Engineering, State Key Laboratory of Terahertz and Millimeter Waves, City University of Hong Kong, Hong Kong, China
3 shared publications - Yue Zhao
State Key Laboratory of Radio Frequency Heterogeneous Integration Shenzhen University Shenzhen China
3 shared publications - Ri-Yao Guo
State Key Laboratory of Radio Frequency Heterogeneous Integration, Shenzhen University, Shenzhen, China
2 shared publications - Xujun Yang
Anhui Agricultural University
2 shared publications - Chow-Yen-Desmond Sim
National Sun Yat-Sen University
1 shared publication
Latest Publications
- 24 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (9) , 6886-6896
A High-Gain Aperture-Shared Dual-Band Circularly Polarized Antenna Using Polarizer Integrated Dual-Functional Surface
An aperture-shared dual-band circularly polarized (CP) antenna is proposed. It is the first attempt to propose a polarizer integrated dual-functional surface (PIDFS), enabling the co-designing of a CP reflectarray (RA) and a CP Fabry Perot cavity (FPC) antenna while keeping wideband and high-gain performances. The proposed work divides a traditional polarizer into two distinct parts with a dual-function reflective surface sandwiched in between. The proposed PIDFS provides wave reflection with polarization rotation at higher frequency band, contributing to the realization of a millimeter-wave CP RA. At the same time, it also functions as CP partially reflective surface (PRS) for a high-gain FPC antenna designed at lower frequency spectrum. For validation, a prototype of the aperture-shared dual-band CP antenna operating at 7 and 30 GHz bands is designed, fabricated, and measured. 3-dB gain bandwidths of 14 % and 26% with peak gains of 17.3 and 20.5 dBic over two bands are achieved, respectively. The proposed design demonstrates a new design method/scheme to construct a high-gain, aperture-shared antenna with large frequency ratio, superior bandwidth and CP radiation characteristics. With these, it is a good candidate for future communications system that require high integration, wideband and high-CP-gain.
- 24 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (9) , 6886-6896
A High-Gain Aperture-Shared Dual-Band Circularly Polarized Antenna Using Polarizer Integrated Dual-Functional Surface
An aperture-shared dual-band circularly polarized (CP) antenna is proposed. It is the first attempt to propose a polarizer integrated dual-functional surface (PIDFS), enabling the co-designing of a CP reflectarray (RA) and a CP Fabry Perot cavity (FPC) antenna while keeping wideband and high-gain performances. The proposed work divides a traditional polarizer into two distinct parts with a dual-function reflective surface sandwiched in between. The proposed PIDFS provides wave reflection with polarization rotation at higher frequency band, contributing to the realization of a millimeter-wave CP RA. At the same time, it also functions as CP partially reflective surface (PRS) for a high-gain FPC antenna designed at lower frequency spectrum. For validation, a prototype of the aperture-shared dual-band CP antenna operating at 7 and 30 GHz bands is designed, fabricated, and measured. 3-dB gain bandwidths of 14 % and 26% with peak gains of 17.3 and 20.5 dBic over two bands are achieved, respectively. The proposed design demonstrates a new design method/scheme to construct a high-gain, aperture-shared antenna with large frequency ratio, superior bandwidth and CP radiation characteristics. With these, it is a good candidate for future communications system that require high integration, wideband and high-CP-gain.
- 24 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (10) , 3014-3017
A Millimeter-Wave Filtering Fabry–Pérot Cavity Antenna
This paper introduces a novel filtering technique for designing a millimeter-wave (mmw) Fabry-Pérot cavity (FPC) antenna. The paper introduces a new surface combining high dielectric layer, air layer and FSS layer, forming the proposed partially reflective surface with frequency selectivity (PRSFS). Unlike traditional partially reflective surface (PRS) in FPC, the proposed PRSFS not only functions as a PRS, contributing to a high-gain FP antenna, but also functions as a frequency selective surface (FSS) for transmitting waves, resulting in a bandpass filtering response with high frequency selectivity. For demonstration, a 60 GHz filtering FPC antenna is implemented. Compared to recently reported filtering FP type antenna, the proposed antenna yields higher levels of performances such as operating frequency (60.5 GHz), antenna gain (17.7 dBi) and outof-band rejection level (15.2 dB). The proposed filtering antenna is a potential choice for millimeter-wave communications.
- 24 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (10) , 3014-3017
A Millimeter-Wave Filtering Fabry–Pérot Cavity Antenna
This paper introduces a novel filtering technique for designing a millimeter-wave (mmw) Fabry-Pérot cavity (FPC) antenna. The paper introduces a new surface combining high dielectric layer, air layer and FSS layer, forming the proposed partially reflective surface with frequency selectivity (PRSFS). Unlike traditional partially reflective surface (PRS) in FPC, the proposed PRSFS not only functions as a PRS, contributing to a high-gain FP antenna, but also functions as a frequency selective surface (FSS) for transmitting waves, resulting in a bandpass filtering response with high frequency selectivity. For demonstration, a 60 GHz filtering FPC antenna is implemented. Compared to recently reported filtering FP type antenna, the proposed antenna yields higher levels of performances such as operating frequency (60.5 GHz), antenna gain (17.7 dBi) and outof-band rejection level (15.2 dB). The proposed filtering antenna is a potential choice for millimeter-wave communications.
- 7 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (3) , 2897-2902
Design of a Novel Wideband Reconfigurable Transmit-Reflect-Array Antenna Utilizing Twin Lines
This paper proposes a novel topology that enables the integration of a reflect-array (RA) and a transmit-array (TA). Based on this topology, a reconfigurable transmit-reflect-array (RTRA) antenna is physically implemented, capable of switching between a 1-bit reconfigurable RA mode and a fixed beam TA mode. The key to achieving this functionality is the proposed 3-state reconfigurable circuit, which utilizes two shunt PIN diodes to generate two reflection states with a 180° phase difference and one transmission state. Twin line is selected to build the reconfigurable circuit due to the discovery that the characteristic impedance of the transmission line is critical to the ON/OFF performance of the shunt PIN diodes. As a natural consequence, half-wavelength-dipole antennas, which can be simply fed by the twin line, are used as the receiving and radiating elements. After loading the dipole antennas to the reconfigurable circuit, the length of the in-between transmission line is adjusted to stabilize the original frequency-dependent phase difference between the two reflection states at around 180° with a small variation over a wide band. A 16×16-element array was constructed and measured, demonstrating over 36% bandwidth in the broadside RA and TA modes with maximum aperture efficiencies of 27% and 29% respectively. In terms of the beam steering characteristic in the RA mode, the antenna can cover ±45° in both the E- and H- planes. It is also noteworthy that the entire RTRA surface, including the DC biasing network, is fabricated using single-layer PCBs, thus making the proposed design easy and cost-effective to fabricate.
- 7 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (3) , 2897-2902
Design of a Novel Wideband Reconfigurable Transmit-Reflect-Array Antenna Utilizing Twin Lines
This paper proposes a novel topology that enables the integration of a reflect-array (RA) and a transmit-array (TA). Based on this topology, a reconfigurable transmit-reflect-array (RTRA) antenna is physically implemented, capable of switching between a 1-bit reconfigurable RA mode and a fixed beam TA mode. The key to achieving this functionality is the proposed 3-state reconfigurable circuit, which utilizes two shunt PIN diodes to generate two reflection states with a 180° phase difference and one transmission state. Twin line is selected to build the reconfigurable circuit due to the discovery that the characteristic impedance of the transmission line is critical to the ON/OFF performance of the shunt PIN diodes. As a natural consequence, half-wavelength-dipole antennas, which can be simply fed by the twin line, are used as the receiving and radiating elements. After loading the dipole antennas to the reconfigurable circuit, the length of the in-between transmission line is adjusted to stabilize the original frequency-dependent phase difference between the two reflection states at around 180° with a small variation over a wide band. A 16×16-element array was constructed and measured, demonstrating over 36% bandwidth in the broadside RA and TA modes with maximum aperture efficiencies of 27% and 29% respectively. In terms of the beam steering characteristic in the RA mode, the antenna can cover ±45° in both the E- and H- planes. It is also noteworthy that the entire RTRA surface, including the DC biasing network, is fabricated using single-layer PCBs, thus making the proposed design easy and cost-effective to fabricate.
- 18 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (11) , 8441-8449
High-Gain Omnidirectional Transmitarray Antenna
A new omnidirectional transmitarray antenna (TA) is proposed to realize the high gain and high omnidirectionality for millimeter-wave (mmW) applications. The antenna consists of a feeding probe as the source of the TA and an annular receiving/transmitting (Re/Tr) array surrounding the probe. The Re/Tr unit cell is composed of a pair of back-to-back angled dipoles and a delay line. The unit cell utilizes the rotation freedom of the direction of the Tr unit for a 0°/180° phase shift (1 bit), and an additional delay line between the Re and Tr cells for a continuous phase shift between 180°. Then, 1 bit+ Re/Tr unit cells with a continuous phase shift between 0° and 360° are built to form an omnidirectional array. By tuning the phase distribution of the longitudinal cells, the array can compress a wide conical omnidirectional beam from the probe radiator into a high-gain narrow omnidirectional beam in the azimuth plane. Measurement results show that the operating bandwidth of the antenna is 14.2% (from 26.1 to 30.1 GHz), within which the antenna can achieve a high gain of around 8.0 dBi and a stable omnidirectional beam. The design that transplants the concept of TA into a high-gain omnidirectional antenna is proposed for the first time. The proposed omnidirectional TA shows the advantages of remarkable omnidirectionality, broad bandwidth, and low cross-polarization level.
- 18 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (11) , 8441-8449
High-Gain Omnidirectional Transmitarray Antenna
A new omnidirectional transmitarray antenna (TA) is proposed to realize the high gain and high omnidirectionality for millimeter-wave (mmW) applications. The antenna consists of a feeding probe as the source of the TA and an annular receiving/transmitting (Re/Tr) array surrounding the probe. The Re/Tr unit cell is composed of a pair of back-to-back angled dipoles and a delay line. The unit cell utilizes the rotation freedom of the direction of the Tr unit for a 0°/180° phase shift (1 bit), and an additional delay line between the Re and Tr cells for a continuous phase shift between 180°. Then, 1 bit+ Re/Tr unit cells with a continuous phase shift between 0° and 360° are built to form an omnidirectional array. By tuning the phase distribution of the longitudinal cells, the array can compress a wide conical omnidirectional beam from the probe radiator into a high-gain narrow omnidirectional beam in the azimuth plane. Measurement results show that the operating bandwidth of the antenna is 14.2% (from 26.1 to 30.1 GHz), within which the antenna can achieve a high gain of around 8.0 dBi and a stable omnidirectional beam. The design that transplants the concept of TA into a high-gain omnidirectional antenna is proposed for the first time. The proposed omnidirectional TA shows the advantages of remarkable omnidirectionality, broad bandwidth, and low cross-polarization level.
- 21 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (10) , 8320-8325
A Two-Port RF Device Integrating Dual-Polarized Filtenna and Bandpass Filter Functions With Independent Reconfigurability
In this communication, a two-port RF device integrating polarization-reconfigurable dual-polarized filtenna (PRDPF) and frequency-reconfigurable bandpass filter (FRBF) functions is proposed. For the PRDPF function, a quarter-dielectric-wavelength open stub is introduced into the feedline of each port, enhancing the roll-off rate at the upper-band edge of the realized gain. A 3D-printed polarizer is implemented over the proposed RF device to achieve polarization reconfigurability. For the FRBF realization, two resonators are connected to the feedlines, providing a filtering transmission path at the lower frequency spectrum without occupying extra area. By inserting the varactors into the filtering transmission path, the operating frequency of the filter can be tuned continuously with a constant bandwidth. Experimental results show that the device functions as a PRDPF at 3.7 GHz, and simultaneously as a FRBF at around 2.1 GHz. As for the PRDPF function, the measured average gains of 9.8 dBi and 9.5 dBic are obtained for the linearly and circularly polarized (LP and CP) states, respectively, with the out-of-band suppression levels of more than 22 dB. The measured overlapped bandwidth of impedance matching (| S 11 |, | S 22 | < -10 dB) and axial ratio (AR) < 3 dB is 17%. With respect to the FRBF operation, three tunable operating bands with a constant bandwidth of 20% are illustrated. With the innovative reuse of the feeding network, the proposed structure provides a design method for the future communication systems with high integration level.
- 21 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (10) , 8320-8325
A Two-Port RF Device Integrating Dual-Polarized Filtenna and Bandpass Filter Functions With Independent Reconfigurability
In this communication, a two-port RF device integrating polarization-reconfigurable dual-polarized filtenna (PRDPF) and frequency-reconfigurable bandpass filter (FRBF) functions is proposed. For the PRDPF function, a quarter-dielectric-wavelength open stub is introduced into the feedline of each port, enhancing the roll-off rate at the upper-band edge of the realized gain. A 3D-printed polarizer is implemented over the proposed RF device to achieve polarization reconfigurability. For the FRBF realization, two resonators are connected to the feedlines, providing a filtering transmission path at the lower frequency spectrum without occupying extra area. By inserting the varactors into the filtering transmission path, the operating frequency of the filter can be tuned continuously with a constant bandwidth. Experimental results show that the device functions as a PRDPF at 3.7 GHz, and simultaneously as a FRBF at around 2.1 GHz. As for the PRDPF function, the measured average gains of 9.8 dBi and 9.5 dBic are obtained for the linearly and circularly polarized (LP and CP) states, respectively, with the out-of-band suppression levels of more than 22 dB. The measured overlapped bandwidth of impedance matching (| S 11 |, | S 22 | < -10 dB) and axial ratio (AR) < 3 dB is 17%. With respect to the FRBF operation, three tunable operating bands with a constant bandwidth of 20% are illustrated. With the innovative reuse of the feeding network, the proposed structure provides a design method for the future communication systems with high integration level.