Mark Hagen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mark Hagen has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Na Kong
Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 USA
2 shared publications - Ali Davoudi
University of Illinois at Urbana-Champaign, Urbana, IL 61081 USA
1 shared publication - Ali Davoudi
Dept. of Electr. & Comput. Eng., Univ. of Illinois, Urbana, IL, USA
1 shared publication - Dong Sam Ha
Department of Electrical and Computer Engineering, Virginia Tech, Blacksburg, VA, USA
1 shared publication - Eric Oettinger
Texas Instruments Incorporated, Rochester, MN 55901 USA
1 shared publication - Fred. C. Lee
Center for Power Electronics Systems, Virginia Tech, Blacksburg, VA, USA
1 shared publication
Latest Publications
- 1 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10482334,p. 259-263
Automated System Identification of Digitally-Controlled Multi-phase DC-DC Converters
Real-time system identification is desirable for designing a proper feedback controller in a practical system. Digital control provides the potential advantages of on-line programmability to apply adaptive control. The digital nature of the feedback signal facilitates the communication between the converter and the processing unit (e.g., microcontroller). These features of digital control make it possible to estimate the real-time system parameters by means of system identification in situ (in-place), and then design and configure the controller accordingly. In this paper, an automated system identification method for digitally-controlled multi-phase DC-DC converters is set forth. Fourier analysis is utilized because of the potential for closed-loop identification and high measurement signal-to-noise ratio. The phase loss and zero-order-hold due to digital control are considered. The identification results for single- and multi-phase DC-DC converters closely match those obtained from conventional network analyzer and models. The proposed method can be done by a stand-alone digital controller; therefore it eliminates the expense of external test equipment. The identification results can be used for controller configuration without pre-existing knowledge of the power stage parameters. This opens up a possibility of moving the determination of the loop compensation from a lab bench to a factory floor or even to an end customer's application.
- 1 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10482334,p. 259-263
Automated System Identification of Digitally-Controlled Multi-phase DC-DC Converters
Real-time system identification is desirable for designing a proper feedback controller in a practical system. Digital control provides the potential advantages of on-line programmability to apply adaptive control. The digital nature of the feedback signal facilitates the communication between the converter and the processing unit (e.g., microcontroller). These features of digital control make it possible to estimate the real-time system parameters by means of system identification in situ (in-place), and then design and configure the controller accordingly. In this paper, an automated system identification method for digitally-controlled multi-phase DC-DC converters is set forth. Fourier analysis is utilized because of the potential for closed-loop identification and high measurement signal-to-noise ratio. The phase loss and zero-order-hold due to digital control are considered. The identification results for single- and multi-phase DC-DC converters closely match those obtained from conventional network analyzer and models. The proposed method can be done by a stand-alone digital controller; therefore it eliminates the expense of external test equipment. The identification results can be used for controller configuration without pre-existing knowledge of the power stage parameters. This opens up a possibility of moving the determination of the loop compensation from a lab bench to a factory floor or even to an end customer's application.
- 1 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10482334,p. 626-630
A General Framework for Automated Tuning of Digital Controllers in Multi-phase Dc-Dc Converters
Digital controllers are widely used in interleaved multi-phase dc-dc converters. The inherent nonlinearities introduced by the nonlinear control rules, quantizers, and mapping between analog and digital domains complicates the controller design process. A simple, yet accurate auto-tuning framework is set forth that provides the required controller coefficients to meet desired time and frequency performance criteria. This is an optimization-based process which minimizes a cost function formulated using error terms. The proposed methodology is implemented on a dual-phase buck converter with a regulated output voltage and drastic change in the load current. The desired performance is verified in time and frequency domains using hardware measurements and numerical simulations.
- 1 February 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10482334,p. 626-630
A General Framework for Automated Tuning of Digital Controllers in Multi-phase Dc-Dc Converters
Digital controllers are widely used in interleaved multi-phase dc-dc converters. The inherent nonlinearities introduced by the nonlinear control rules, quantizers, and mapping between analog and digital domains complicates the controller design process. A simple, yet accurate auto-tuning framework is set forth that provides the required controller coefficients to meet desired time and frequency performance criteria. This is an optimization-based process which minimizes a cost function formulated using error terms. The proposed methodology is implemented on a dual-phase buck converter with a regulated output voltage and drastic change in the load current. The desired performance is verified in time and frequency domains using hardware measurements and numerical simulations.