Zhangfu Yuan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zhangfu Yuan has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Hongxin Zhao
Collaborative Innovation Center of steel Technology, University of Science and Technology Beijing, Beijing, People’s Republic of China
5 shared publications Han Zhang
Collaborative Innovation Center of Steel Technology University of Science and Technology Beijing Beijing 100083 China
4 shared publicationsKe Liu
Collaborative Innovation Center of Steel Technology University of Science and Technology Beijing Beijing 100083 China
3 shared publicationsBingsheng Xu
Research Branch of Resource and Environment China National Institute of Standardization Beijing 100191 China
2 shared publicationsDong Kong
Collaborative Innovation Center of Steel Technology University of Science and Technology Beijing Beijing 100083 China
2 shared publicationsLinfei Zhao
Collaborative Innovation Center of Steel Technology University of Science and Technology Beijing Beijing 100083 China
2 shared publications
Latest Publications
- Open Access
- 15 June 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (7) , 914-924
Characteristics of Supersonic Oxygen Jet in RH Vacuum Refining Furnace
RH is one of the essential secondary refining processes, and the oxygen lance plays a significant part in its multi-functionalization. Therefore, it is necessary to dig deeper into the jet characteristics at low ambient pressure. This study examined the supersonic oxygen jet parameters, such as the jet Mach number, dynamic pressure, turbulence kinetic energy, and half-jet width with computational fluid dynamics, for RH vacuum furnaces operating at ambient pressures ranging from 4000 to 1000 Pa and 101325 Pa. Underexpanded jets were observed at the ambient pressures from 4000 to 1000 Pa, and single strong barrel shocks existed. It was shown that decreasing the back pressure significantly improved the axial and radial Mach number of the jet. However, this improvement was related to a sacrifice of the dynamic pressure. The length of the potential core region and supersonic region increased greatly with decreased ambient pressure. The decrease in ambient pressure also considerably increased the turbulence kinetic energy, indicating a heightened level of energy transfer. However, the correlation between the half-jet width and the ambient pressure was not a simple linear relationship. The half-jet width increased with the ambient pressure decreasing from 4000 Pa to 1000 Pa.
- 15 June 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (7) , 914-924
Open AccessCharacteristics of Supersonic Oxygen Jet in RH Vacuum Refining Furnace
RH is one of the essential secondary refining processes, and the oxygen lance plays a significant part in its multi-functionalization. Therefore, it is necessary to dig deeper into the jet characteristics at low ambient pressure. This study examined the supersonic oxygen jet parameters, such as the jet Mach number, dynamic pressure, turbulence kinetic energy, and half-jet width with computational fluid dynamics, for RH vacuum furnaces operating at ambient pressures ranging from 4000 to 1000 Pa and 101325 Pa. Underexpanded jets were observed at the ambient pressures from 4000 to 1000 Pa, and single strong barrel shocks existed. It was shown that decreasing the back pressure significantly improved the axial and radial Mach number of the jet. However, this improvement was related to a sacrifice of the dynamic pressure. The length of the potential core region and supersonic region increased greatly with decreased ambient pressure. The decrease in ambient pressure also considerably increased the turbulence kinetic energy, indicating a heightened level of energy transfer. However, the correlation between the half-jet width and the ambient pressure was not a simple linear relationship. The half-jet width increased with the ambient pressure decreasing from 4000 Pa to 1000 Pa.
- 25 January 2025
- Published by Wiley in Steel Research International
- Vol. 96 (9) , 310-320
Thermodynamic Evaluation of Enhanced CO2 Conversion in Innovative Slag Splashing Processes in Converters
The innovative slag splashing technique enhances the recycling of CO2 in the steel industry. However, thermodynamic experiments overestimate CO2 conversion because the temperature drop in the process is not taken into account. Therefore, FactSage is employed to reevaluate it. Calculations are validated by comparison with experiments. It is found that employing CO2 for the slag splashing process leads to a decrease in equilibrium temperature. Increasing the carbon addition enhances CO generation and CO2 conversion but results in a further reduced temperature. Elevating the temperatures of the slag and CO2 has no effect on CO generation and CO2 conversion. However, it proves beneficial for increasing the equilibrium temperature. As the most effective measure, increasing the FeO content in the slag improves CO2 conversion while significantly lowering the slag solid fraction. When the initial FeO content is 17.24 mass%, the initial temperature is 1873 K, and the CO2 temperature is 300 K, the optimal carbon addition is 1.5 mass%. By increasing the slag and CO2 temperatures and elevating the initial FeO content, the carbon addition can reach 3.0 mass%, and CO2 conversion reaches 53.29%.
- 25 January 2025
- Published by Wiley in Steel Research International
- Vol. 96 (9) , 310-320
Thermodynamic Evaluation of Enhanced CO2 Conversion in Innovative Slag Splashing Processes in Converters
The innovative slag splashing technique enhances the recycling of CO2 in the steel industry. However, thermodynamic experiments overestimate CO2 conversion because the temperature drop in the process is not taken into account. Therefore, FactSage is employed to reevaluate it. Calculations are validated by comparison with experiments. It is found that employing CO2 for the slag splashing process leads to a decrease in equilibrium temperature. Increasing the carbon addition enhances CO generation and CO2 conversion but results in a further reduced temperature. Elevating the temperatures of the slag and CO2 has no effect on CO generation and CO2 conversion. However, it proves beneficial for increasing the equilibrium temperature. As the most effective measure, increasing the FeO content in the slag improves CO2 conversion while significantly lowering the slag solid fraction. When the initial FeO content is 17.24 mass%, the initial temperature is 1873 K, and the CO2 temperature is 300 K, the optimal carbon addition is 1.5 mass%. By increasing the slag and CO2 temperatures and elevating the initial FeO content, the carbon addition can reach 3.0 mass%, and CO2 conversion reaches 53.29%.
- 18 June 2024
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 51 (8) , 753-765
Thermodynamic simulation of slag–refractories interactions in innovative slag-splashing processes in converters
The innovative slag-splashing process in converters enables the reuse of CO2. However, the changes in slag–refractories interactions after applying the new technique are not yet clear. In this work, an approach was developed to thermodynamically simulate the slag–refractories interactions in slag-splashing processes. Firstly, the simulation was validated. Subsequently, the differences in traditional and innovative slag-splashing processes were compared, and the effects of slag carbon addition, CO2 consumption, and refractories composition on slag–refractories interactions were investigated. It was found that after applying the new technique, the mass of the high-melting-point solid solution increased, and the liquid slag had a better bonding effect on the refractories and the external mechanical bonding layer. Increasing the slag carbon addition and CO2 consumption both led to an increase in high-melting-point solid solution. However, increasing the slag carbon addition favoured the bonding of liquid slag to the refractories, while increasing the CO2 consumption weakened the bonding ability of the liquid slag. The increase of C in MgO–C refractories resulted in an increase in Fe and CO production. Due to the deterioration of slag wettability on refractories, the increase in C is detrimental to the converter slag-splashing process.
- 18 June 2024
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 51 (8) , 753-765
Thermodynamic simulation of slag–refractories interactions in innovative slag-splashing processes in converters
The innovative slag-splashing process in converters enables the reuse of CO2. However, the changes in slag–refractories interactions after applying the new technique are not yet clear. In this work, an approach was developed to thermodynamically simulate the slag–refractories interactions in slag-splashing processes. Firstly, the simulation was validated. Subsequently, the differences in traditional and innovative slag-splashing processes were compared, and the effects of slag carbon addition, CO2 consumption, and refractories composition on slag–refractories interactions were investigated. It was found that after applying the new technique, the mass of the high-melting-point solid solution increased, and the liquid slag had a better bonding effect on the refractories and the external mechanical bonding layer. Increasing the slag carbon addition and CO2 consumption both led to an increase in high-melting-point solid solution. However, increasing the slag carbon addition favoured the bonding of liquid slag to the refractories, while increasing the CO2 consumption weakened the bonding ability of the liquid slag. The increase of C in MgO–C refractories resulted in an increase in Fe and CO production. Due to the deterioration of slag wettability on refractories, the increase in C is detrimental to the converter slag-splashing process.
- 8 May 2024
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 10 (2) , 864-879
Numerical Simulation of Innovative Slag Splashing Process in a Converter Using a Nozzle-Twisted Oxygen Lance
- 8 May 2024
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 10 (2) , 864-879
Numerical Simulation of Innovative Slag Splashing Process in a Converter Using a Nozzle-Twisted Oxygen Lance
- 9 July 2023
- Published by Wiley in Steel Research International
- Vol. 94 (10)
Numerical Simulation of CO2 Used for Slag Splashing Process in Converter
Utilizing CO2 for the slag splashing process presents a novel approach that enhances CO2 utilization in the steel industry and promotes efficient slag splashing. Herein, numerical simulation is employed to investigate the kinetic feasibility of this technique on a 100 t converter. The volume of fluid (VOF) model is utilized to trace the gas–slag interface, while the standard k–ε model is selected to describe the turbulent flow of each phase. Initially, the model is validated via isentropic theory and experimental data. Subsequently, the effects of gas and oxygen lance replacement are evaluated. The results indicate that employing CO2 solely instead of N2 leads to a reduction in jet velocity and slag mass flow rates at different positions. However, the utilization of the innovative oxygen lance slows down the jet decay and increases the slag mass flow rate at various heights and sidewalls, except for the lower cone, resulting in a satisfactory slag splashing performance. The present study verifies the feasibility of this new technology and its potential to contribute to CO2 reduction in the industry positively.
- 9 July 2023
- Published by Wiley in Steel Research International
- Vol. 94 (10)
Numerical Simulation of CO2 Used for Slag Splashing Process in Converter
Utilizing CO2 for the slag splashing process presents a novel approach that enhances CO2 utilization in the steel industry and promotes efficient slag splashing. Herein, numerical simulation is employed to investigate the kinetic feasibility of this technique on a 100 t converter. The volume of fluid (VOF) model is utilized to trace the gas–slag interface, while the standard k–ε model is selected to describe the turbulent flow of each phase. Initially, the model is validated via isentropic theory and experimental data. Subsequently, the effects of gas and oxygen lance replacement are evaluated. The results indicate that employing CO2 solely instead of N2 leads to a reduction in jet velocity and slag mass flow rates at different positions. However, the utilization of the innovative oxygen lance slows down the jet decay and increases the slag mass flow rate at various heights and sidewalls, except for the lower cone, resulting in a satisfactory slag splashing performance. The present study verifies the feasibility of this new technology and its potential to contribute to CO2 reduction in the industry positively.
- Open Access
- 30 January 2022
- Published by MDPI AG in Separations
- Vol. 9 (2) , 37
A Pilot-Scale Treatment of Steel Plant Wastewater by PVDF Hollow Fiber Ultrafiltration Membrane with Low Packing Density
The treatment of wastewater from the iron and steel industry is difficult due to its complex and changeable characteristics. This paper introduces the application of polyvinylidene fluoride (PVDF)-pressurized ultrafiltration membrane with low packing density that produced via thermally induced phase separation (TIPS) in wastewater of iron and steel industry, to study the effects of packing density of ultrafiltration membrane modules as well as the membrane performance under different operation conditions, in order to provide guidance for the subsequent development of other ultrafiltration applications in wastewater of iron and steel. The results show a significant positive effect of smaller packing density on the transmembrane pressure difference (TMP) reducing and higher permeability. Under 30 min filtration cycle and 65 L m−2 h−1 (LMH) operation flux, the permeability can be stabilized to 200 L/(m2·h)/0.1 MPa, which is two times higher than that of the membrane module with 0.3 m2/m3 higher packing density under the same condition. It is obvious that compared with enhanced flux maintenance (EFM), chemically enhanced backwash (CEB) is a more effective cleaning method for iron and steel wastewater, which maintains TMP (30 kPa) without any significant increase under the premise of ensuring the high-flux (65 LMH) operation. The results also suggest reasonable parameters based on the test water quality, which include the filtration cycle and operation flux. The scanning electron microscopy (SEM) analysis and the turbidity of the permeate show that the ultrafiltration membrane has good intercept ability and high anti-pollution performance.
- 30 January 2022
- Published by MDPI AG in Separations
- Vol. 9 (2) , 37
Open AccessA Pilot-Scale Treatment of Steel Plant Wastewater by PVDF Hollow Fiber Ultrafiltration Membrane with Low Packing Density
The treatment of wastewater from the iron and steel industry is difficult due to its complex and changeable characteristics. This paper introduces the application of polyvinylidene fluoride (PVDF)-pressurized ultrafiltration membrane with low packing density that produced via thermally induced phase separation (TIPS) in wastewater of iron and steel industry, to study the effects of packing density of ultrafiltration membrane modules as well as the membrane performance under different operation conditions, in order to provide guidance for the subsequent development of other ultrafiltration applications in wastewater of iron and steel. The results show a significant positive effect of smaller packing density on the transmembrane pressure difference (TMP) reducing and higher permeability. Under 30 min filtration cycle and 65 L m−2 h−1 (LMH) operation flux, the permeability can be stabilized to 200 L/(m2·h)/0.1 MPa, which is two times higher than that of the membrane module with 0.3 m2/m3 higher packing density under the same condition. It is obvious that compared with enhanced flux maintenance (EFM), chemically enhanced backwash (CEB) is a more effective cleaning method for iron and steel wastewater, which maintains TMP (30 kPa) without any significant increase under the premise of ensuring the high-flux (65 LMH) operation. The results also suggest reasonable parameters based on the test water quality, which include the filtration cycle and operation flux. The scanning electron microscopy (SEM) analysis and the turbidity of the permeate show that the ultrafiltration membrane has good intercept ability and high anti-pollution performance.
- 12 February 2020
- Published by Springer Nature
- p. 669-675
Fe2O3 Nano-particles Grown on Carbon Fabric as a Freestanding Anode for High-Performance Lithium-Ion Batteries
- 12 February 2020
- Published by Springer Nature
- p. 669-675
Fe2O3 Nano-particles Grown on Carbon Fabric as a Freestanding Anode for High-Performance Lithium-Ion Batteries
- 25 January 2020
- Published by Springer Nature in The Minerals, Metals & Materials Series
- p. 479-487
Effect of Alumina Ceramics Surface Condition on the Wetting of Liquid Lead
- 25 January 2020
- Published by Springer Nature in The Minerals, Metals & Materials Series
- p. 479-487
Effect of Alumina Ceramics Surface Condition on the Wetting of Liquid Lead