Hyeon Kang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hyeon Kang has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Eun-Chae Kim
Department of Dental Laboratory Technology, Gwangju Health University, 73, Bungmun-daero 419beon-gil, Gwangsan-gu, Gwangju 62287, Republic of Korea
1 shared publication - Kwi-Dug Yun
Department of Prosthodontics, School of Dentistry, Chonnam National University, Gwangju, Republic of Korea
1 shared publication - Sang-Won Park
Department of Prosthodontics, School of Dentistry, Chonnam National University, Gwangju, Republic of Korea
1 shared publication - Yangan Yun
Department of Prosthodontics, School of Dentistry, Chonnam National University, 33 Yongbongro, Bukgu, Gwangju 61186, Republic of Korea
1 shared publication - Yong-Seok Lee
Department of Mechanical Engineering, Konkuk University, Seoul 05029, Republic of Korea
1 shared publication
Latest Publications
- Open Access
- 13 April 2023
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 24 (8) , 7203
Fundamental Properties and Clinical Application of 3D-Printed Bioglass Porcelain Fused to Metal Dental Restoration
The purpose of this study is to evaluate the mechanical properties and clinical fitness of 3D-printed bioglass porcelain fused to metal (PFM) dental crowns. To evaluate the mechanical properties, tensile strength, Vickers microhardness, shear bond strength, and surface roughness tests of the SLM printed Co-Cr alloy was conducted. A right mandibular 1st molar tooth was prepared for a single dental crown (n = 10). For a three-unit metal crown and bridge, the right mandibular first premolar and first molar were prepared. Bioglass porcelain was fired to fabricate PFM dental restorations. A clinical gap was observed and measured during each of the four times porcelain was fired. A statistical analysis was conducted. The SLM technique showed the largest statistically significant tensile strength and a 0.2% yield strength value. The milling technique had the lowest statistically significant compressive strength value. The shear bond strength and surface roughness showed no statistically significant difference between the fabricated method. There was a statistically significant change in marginal discrepancy according to the porcelain firing step. The casting technique showed the greatest statistically significant margin discrepancy value. The SLM method showed better fitness than the traditional casting method and showed better mechanical properties as a dental material.
- 13 April 2023
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 24 (8) , 7203
Open AccessFundamental Properties and Clinical Application of 3D-Printed Bioglass Porcelain Fused to Metal Dental Restoration
The purpose of this study is to evaluate the mechanical properties and clinical fitness of 3D-printed bioglass porcelain fused to metal (PFM) dental crowns. To evaluate the mechanical properties, tensile strength, Vickers microhardness, shear bond strength, and surface roughness tests of the SLM printed Co-Cr alloy was conducted. A right mandibular 1st molar tooth was prepared for a single dental crown (n = 10). For a three-unit metal crown and bridge, the right mandibular first premolar and first molar were prepared. Bioglass porcelain was fired to fabricate PFM dental restorations. A clinical gap was observed and measured during each of the four times porcelain was fired. A statistical analysis was conducted. The SLM technique showed the largest statistically significant tensile strength and a 0.2% yield strength value. The milling technique had the lowest statistically significant compressive strength value. The shear bond strength and surface roughness showed no statistically significant difference between the fabricated method. There was a statistically significant change in marginal discrepancy according to the porcelain firing step. The casting technique showed the greatest statistically significant margin discrepancy value. The SLM method showed better fitness than the traditional casting method and showed better mechanical properties as a dental material.