Artur Nassyrbayev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Artur Nassyrbayev has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Ivan Shanenkov
School of Energy and Power Engineering, National Research Tomsk Polytechnic University, Russian Federation, Tomsk, Russian Federation
7 shared publications - Dmitriy Sergeevich Nikitin
National Research Tomsk Polytechnic University, Tomsk, Russia
6 shared publications - Aleksandr I. Tsimmerman
National Research Tomsk Polytechnic University, Tomsk, Russia
4 shared publications - Alexander Anatolyevich Sivkov
National Research Tomsk Polytechnic University, Tomsk, Russia
4 shared publications - Egor D. Kuzmenko
National Research Tomsk Polytechnic University
3 shared publications - Yuliya Shanenkova
National Research Tomsk Polytechnic University
3 shared publications
Latest Publications
- 14 September 2026
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 90 (9) , 1730-1737
Plasma Dynamic Synthesis Productivity of Dispersed Iron Oxides in Single-Pulse Operation Mode
The development of materials for shielding, absorption, and interference suppression is an urgent practical challenge for ensuring the electromagnetic compatibility of devices. Iron-containing compounds are among the most promising radar absorbing materials. This paper studies a plasma dynamic synthesis method for producing dispersed iron oxides. The efficiency of an electrophysical setup based on a coaxial magnetoplasma accelerator with steel electrodes is examined, depending on the process energy parameters and the gaseous environment of the reactor chamber. The most promising experimental conditions for converting the electrical erosion material into an oxide product are achieved with an energy storage voltage of 2.5 kV and a capacitor bank capacitance of 14.4 mF. Other optimization ways for increasing the performance of the developed laboratory setup are also demonstrated.
- 14 September 2026
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 90 (9) , 1730-1737
Plasma Dynamic Synthesis Productivity of Dispersed Iron Oxides in Single-Pulse Operation Mode
The development of materials for shielding, absorption, and interference suppression is an urgent practical challenge for ensuring the electromagnetic compatibility of devices. Iron-containing compounds are among the most promising radar absorbing materials. This paper studies a plasma dynamic synthesis method for producing dispersed iron oxides. The efficiency of an electrophysical setup based on a coaxial magnetoplasma accelerator with steel electrodes is examined, depending on the process energy parameters and the gaseous environment of the reactor chamber. The most promising experimental conditions for converting the electrical erosion material into an oxide product are achieved with an energy storage voltage of 2.5 kV and a capacitor bank capacitance of 14.4 mF. Other optimization ways for increasing the performance of the developed laboratory setup are also demonstrated.
- 9 May 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (15) , 30302-30314
Ti3SiC2-based composites synthesized by vacuum sintering and consolidated by spark plasma sintering: Microstructure and mechanical properties
- 9 May 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (15) , 30302-30314
Ti3SiC2-based composites synthesized by vacuum sintering and consolidated by spark plasma sintering: Microstructure and mechanical properties
- Open Access
- 27 February 2026
- Published by National Research Tomsk Polytechnic University in Bulletin of the Tomsk Polytechnic University Geo Assets Engineering
- Vol. 337 (2) , 149-160
Production of copper powders and metal-matrix composites with copper matrix in arc discharge plasma
Relevance. Copper metal matrix composites are widely used in advanced engineering applications involving extreme mechanical loads and increased heat flows. They are particularly important in the electronics industry, where they are used as substrates for discrete power components and heat sinks. These materials can effectively dissipate heat from electronic components, which is important given the predicted growth in local heat flows in high-performance devices and their miniaturization. Aim. To synthesize copper powders and metal matrix composites with a copper matrix with arc discharge plasma, for use in the subsequent manufacture of bulk products that have enhanced mechanical and thermophysical properties. Objects. Copper powders, tungsten carbide powders, and metal matrix composites with a copper matrix reinforced with tungsten carbide, as well as bulk products made from these powders. Methods. Plasma dynamic synthesis, spark plasma sintering, X-ray diffractometry (XRD analysis), scanning electron microscopy, transmission electron microscopy, indentation (microhardness measurement), laser flash method (thermal conductivity measurement). Results. The plasma dynamic method was used to synthesize powders of copper, nanodispersed tungsten carbide and metal matrix composites based on them. Two fundamental approaches were proposed: ex situ, which is based on the separate production of copper (Cu) and carbides, followed by their mixing; and in situ, which involves the joint production and combination of the matrix and carbides. The authors obtained the dispersed metal matrix composites with a carbide content of 10% and a bimodal particle size distribution ranging from tens of nanometres to hundreds of micrometres. This enabled high-density composite products to be obtained with a relative density of up to 95% and a uniform distribution of the ceramic component in the matrix during sintering. The manufactured composite materials demonstrated significant potential in terms of both their mechanical and thermophysical properties. The bulk products exhibited increased hardness (73–92 HV), combined with satisfactory thermophysical characteristics (λ up to 169 W/m·K). These results may be valuable in developing modern materials capable of operating under extreme mechanical and thermal conditions, a serious problem currently facing the electronics industry.
- 27 February 2026
- Published by National Research Tomsk Polytechnic University in Bulletin of the Tomsk Polytechnic University Geo Assets Engineering
- Vol. 337 (2) , 149-160
Open AccessProduction of copper powders and metal-matrix composites with copper matrix in arc discharge plasma
Relevance. Copper metal matrix composites are widely used in advanced engineering applications involving extreme mechanical loads and increased heat flows. They are particularly important in the electronics industry, where they are used as substrates for discrete power components and heat sinks. These materials can effectively dissipate heat from electronic components, which is important given the predicted growth in local heat flows in high-performance devices and their miniaturization. Aim. To synthesize copper powders and metal matrix composites with a copper matrix with arc discharge plasma, for use in the subsequent manufacture of bulk products that have enhanced mechanical and thermophysical properties. Objects. Copper powders, tungsten carbide powders, and metal matrix composites with a copper matrix reinforced with tungsten carbide, as well as bulk products made from these powders. Methods. Plasma dynamic synthesis, spark plasma sintering, X-ray diffractometry (XRD analysis), scanning electron microscopy, transmission electron microscopy, indentation (microhardness measurement), laser flash method (thermal conductivity measurement). Results. The plasma dynamic method was used to synthesize powders of copper, nanodispersed tungsten carbide and metal matrix composites based on them. Two fundamental approaches were proposed: ex situ, which is based on the separate production of copper (Cu) and carbides, followed by their mixing; and in situ, which involves the joint production and combination of the matrix and carbides. The authors obtained the dispersed metal matrix composites with a carbide content of 10% and a bimodal particle size distribution ranging from tens of nanometres to hundreds of micrometres. This enabled high-density composite products to be obtained with a relative density of up to 95% and a uniform distribution of the ceramic component in the matrix during sintering. The manufactured composite materials demonstrated significant potential in terms of both their mechanical and thermophysical properties. The bulk products exhibited increased hardness (73–92 HV), combined with satisfactory thermophysical characteristics (λ up to 169 W/m·K). These results may be valuable in developing modern materials capable of operating under extreme mechanical and thermal conditions, a serious problem currently facing the electronics industry.
- 21 January 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (9) , 11270-11280
Influence of stoichiometry on the oxidation behavior and mechanical properties of hafnium carbonitride ceramics
- 21 January 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (9) , 11270-11280
Influence of stoichiometry on the oxidation behavior and mechanical properties of hafnium carbonitride ceramics
- 8 January 2026
- Published by Elsevier in Particuology
- Vol. 109, 247-257
Plasma dynamic synthesis of hybrid carbide-reinforced aluminium matrix composites
- 8 January 2026
- Published by Elsevier in Particuology
- Vol. 109, 247-257
Plasma dynamic synthesis of hybrid carbide-reinforced aluminium matrix composites
- Open Access
- 25 June 2025
- Published by National University of Science and Technology MISiS in Powder Metallurgy аnd Functional Coatings
- Vol. 19 (3) , 39-47
Effect of magnesium oxide on the microstructure and mechanical properties of yttria-stabilized zirconia-based ceramics
In the present work, sintering and investigation of composite ceramic materials based on nanostructured MgO–ZrO2 powders were carried out. Zirconium dioxide was additionally stabilized with 3 mol. % yttrium oxide. The nanopowders were pre-treated by mechanical activation using a planetary ball mill at a rotation frequency of 10 Hz. Zirconium dioxide balls were used as the grinding media. The prepared powders were compacted at pressing pressures of 50, 100, 200, and 300 MPa. The compacts were sintered in a high-temperature furnace at 1700 °C. Microstructural studies were performed on the polished surfaces of the sintered samples using scanning electron microscopy (SEM). EDX mapping was conducted to determine the elemental distribution, confirming the presence of two phases in all samples. To evaluate the effectiveness of stabilizing additives on the polymorphic transformation of zirconium dioxide, X-ray diffraction (XRD) analysis was performed. The porosity of the materials and its dependence on the pressing pressure and magnesium oxide content were also assessed. Mechanical properties such as Martens hardness and elastic modulus were measured using a NanoIndenter G200, while flexural strength was evaluated by scratch testing on the same device. Fracture toughness was determined by the indentation method using the Marshall–Evans approach. The influence of magnesium oxide additives on the physical and mechanical properties of the MgO–ZrO2 composite ceramics was established.
- 25 June 2025
- Published by National University of Science and Technology MISiS in Powder Metallurgy аnd Functional Coatings
- Vol. 19 (3) , 39-47
Open AccessEffect of magnesium oxide on the microstructure and mechanical properties of yttria-stabilized zirconia-based ceramics
In the present work, sintering and investigation of composite ceramic materials based on nanostructured MgO–ZrO2 powders were carried out. Zirconium dioxide was additionally stabilized with 3 mol. % yttrium oxide. The nanopowders were pre-treated by mechanical activation using a planetary ball mill at a rotation frequency of 10 Hz. Zirconium dioxide balls were used as the grinding media. The prepared powders were compacted at pressing pressures of 50, 100, 200, and 300 MPa. The compacts were sintered in a high-temperature furnace at 1700 °C. Microstructural studies were performed on the polished surfaces of the sintered samples using scanning electron microscopy (SEM). EDX mapping was conducted to determine the elemental distribution, confirming the presence of two phases in all samples. To evaluate the effectiveness of stabilizing additives on the polymorphic transformation of zirconium dioxide, X-ray diffraction (XRD) analysis was performed. The porosity of the materials and its dependence on the pressing pressure and magnesium oxide content were also assessed. Mechanical properties such as Martens hardness and elastic modulus were measured using a NanoIndenter G200, while flexural strength was evaluated by scratch testing on the same device. Fracture toughness was determined by the indentation method using the Marshall–Evans approach. The influence of magnesium oxide additives on the physical and mechanical properties of the MgO–ZrO2 composite ceramics was established.
- 19 June 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (23) , 40356-40366
Improved mechanical and thermal properties of quasi-ductile metal-ceramic laminated composites produced from Ta foils and Ti3Al(Si)C2 filled preceramic paper
- 19 June 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (23) , 40356-40366
Improved mechanical and thermal properties of quasi-ductile metal-ceramic laminated composites produced from Ta foils and Ti3Al(Si)C2 filled preceramic paper
- 8 February 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (14) , 19080-19090
In-situ carbide reinforced aluminium metal matrix composites obtained in pulsed arc plasma discharge
- 8 February 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (14) , 19080-19090
In-situ carbide reinforced aluminium metal matrix composites obtained in pulsed arc plasma discharge
- 19 September 2024
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 328
Synthesis of titanium diboride by electric arc plasma in air
- 19 September 2024
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 328
Synthesis of titanium diboride by electric arc plasma in air