Egor D. Kuzmenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Egor D. Kuzmenko has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Сергей Вениаминович Матренин
National Research Tomsk Polytechnic University
5 shared publications - Artur Nassyrbayev
National Research Tomsk Polytechnic University, Tomsk, Russia
3 shared publications Artur Nassyrbayev
2 shared publicationsSergey Matrenin
2 shared publicationsAles Buyakov
Tomsk Polytechnic University, Tomsk, Russia
1 shared publicationAlexander Ditts
1 shared publication
Latest Publications
- Open Access
- 16 October 2026
- Published by National University of Science and Technology MISiS in Powder Metallurgy аnd Functional Coatings
- Vol. 20 (3) , 67-73
Mechanical properties and oxidation resistance of hafnium carbonitride hot pressed ceramics
In this study, ceramic hafnium carbonitride samples were obtained, consolidated by hot pressing commercial hafnium carbide and nitride powders. Consolidation was performed at a temperature of 2000 °C, a pressure of 40 MPa, and a holding time of 15 min. The mechanical properties of the materials were determined during the study. It was found that during the formation of hafnium carbonitride, increasing the stoichiometric C:N ratio from 20:80 to 80:20 increases the hardness from 17.7 to 22.9 GPa, Young’s modulus from 452 to 479 GPa, and strength from 622 to 694 MPa. In turn, increasing the nitrogen content increases the crack resistance of the material. A study of the oxidation resistance of materials exposed to high temperatures of 1200 °C revealed that hafnium carbonitride samples exhibited increased oxidation resistance compared to hafnium carbide and hafnium nitride samples. As the carbon content in the carbonitride increased, the oxidation rate decreased. Upon heating, parabolic oxidation kinetics were observed. After oxidative exposure, a dense, highly adhesive oxide layer formed on the surface of the samples.
- 16 October 2026
- Published by National University of Science and Technology MISiS in Powder Metallurgy аnd Functional Coatings
- Vol. 20 (3) , 67-73
Open AccessMechanical properties and oxidation resistance of hafnium carbonitride hot pressed ceramics
In this study, ceramic hafnium carbonitride samples were obtained, consolidated by hot pressing commercial hafnium carbide and nitride powders. Consolidation was performed at a temperature of 2000 °C, a pressure of 40 MPa, and a holding time of 15 min. The mechanical properties of the materials were determined during the study. It was found that during the formation of hafnium carbonitride, increasing the stoichiometric C:N ratio from 20:80 to 80:20 increases the hardness from 17.7 to 22.9 GPa, Young’s modulus from 452 to 479 GPa, and strength from 622 to 694 MPa. In turn, increasing the nitrogen content increases the crack resistance of the material. A study of the oxidation resistance of materials exposed to high temperatures of 1200 °C revealed that hafnium carbonitride samples exhibited increased oxidation resistance compared to hafnium carbide and hafnium nitride samples. As the carbon content in the carbonitride increased, the oxidation rate decreased. Upon heating, parabolic oxidation kinetics were observed. After oxidative exposure, a dense, highly adhesive oxide layer formed on the surface of the samples.
- 15 April 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (14) , 25522-25531
Mechanical properties and oxidation behavior of dual‐phase carbonitride/boride ceramics
- 15 April 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (14) , 25522-25531
Mechanical properties and oxidation behavior of dual‐phase carbonitride/boride ceramics
- 21 January 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (9) , 11270-11280
Influence of stoichiometry on the oxidation behavior and mechanical properties of hafnium carbonitride ceramics
- 21 January 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (9) , 11270-11280
Influence of stoichiometry on the oxidation behavior and mechanical properties of hafnium carbonitride ceramics
- 13 November 2025
- Published by Springer Nature in Glass and Ceramics
- Vol. 82 (7-8) , 315-320
Physical and Mechanical Properties of Ceramic Composite Material Based on Al6Si2O13–ZrSiO4
- 13 November 2025
- Published by Springer Nature in Glass and Ceramics
- Vol. 82 (7-8) , 315-320
Physical and Mechanical Properties of Ceramic Composite Material Based on Al6Si2O13–ZrSiO4
- 25 September 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (28) , 56792-56803
Oxidation behavior and physico-mechanical properties of spark plasma sintered ZrCN-ZrO2 ceramics
- 25 September 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (28) , 56792-56803
Oxidation behavior and physico-mechanical properties of spark plasma sintered ZrCN-ZrO2 ceramics
- Open Access
- 25 June 2025
- Published by National University of Science and Technology MISiS in Powder Metallurgy аnd Functional Coatings
- Vol. 19 (3) , 39-47
Effect of magnesium oxide on the microstructure and mechanical properties of yttria-stabilized zirconia-based ceramics
In the present work, sintering and investigation of composite ceramic materials based on nanostructured MgO–ZrO2 powders were carried out. Zirconium dioxide was additionally stabilized with 3 mol. % yttrium oxide. The nanopowders were pre-treated by mechanical activation using a planetary ball mill at a rotation frequency of 10 Hz. Zirconium dioxide balls were used as the grinding media. The prepared powders were compacted at pressing pressures of 50, 100, 200, and 300 MPa. The compacts were sintered in a high-temperature furnace at 1700 °C. Microstructural studies were performed on the polished surfaces of the sintered samples using scanning electron microscopy (SEM). EDX mapping was conducted to determine the elemental distribution, confirming the presence of two phases in all samples. To evaluate the effectiveness of stabilizing additives on the polymorphic transformation of zirconium dioxide, X-ray diffraction (XRD) analysis was performed. The porosity of the materials and its dependence on the pressing pressure and magnesium oxide content were also assessed. Mechanical properties such as Martens hardness and elastic modulus were measured using a NanoIndenter G200, while flexural strength was evaluated by scratch testing on the same device. Fracture toughness was determined by the indentation method using the Marshall–Evans approach. The influence of magnesium oxide additives on the physical and mechanical properties of the MgO–ZrO2 composite ceramics was established.
- 25 June 2025
- Published by National University of Science and Technology MISiS in Powder Metallurgy аnd Functional Coatings
- Vol. 19 (3) , 39-47
Open AccessEffect of magnesium oxide on the microstructure and mechanical properties of yttria-stabilized zirconia-based ceramics
In the present work, sintering and investigation of composite ceramic materials based on nanostructured MgO–ZrO2 powders were carried out. Zirconium dioxide was additionally stabilized with 3 mol. % yttrium oxide. The nanopowders were pre-treated by mechanical activation using a planetary ball mill at a rotation frequency of 10 Hz. Zirconium dioxide balls were used as the grinding media. The prepared powders were compacted at pressing pressures of 50, 100, 200, and 300 MPa. The compacts were sintered in a high-temperature furnace at 1700 °C. Microstructural studies were performed on the polished surfaces of the sintered samples using scanning electron microscopy (SEM). EDX mapping was conducted to determine the elemental distribution, confirming the presence of two phases in all samples. To evaluate the effectiveness of stabilizing additives on the polymorphic transformation of zirconium dioxide, X-ray diffraction (XRD) analysis was performed. The porosity of the materials and its dependence on the pressing pressure and magnesium oxide content were also assessed. Mechanical properties such as Martens hardness and elastic modulus were measured using a NanoIndenter G200, while flexural strength was evaluated by scratch testing on the same device. Fracture toughness was determined by the indentation method using the Marshall–Evans approach. The influence of magnesium oxide additives on the physical and mechanical properties of the MgO–ZrO2 composite ceramics was established.
- Open Access
- 31 March 2025
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 22 (1) , 85-91
ФИЗИКО-МЕХАНИЧЕСКИЕ СВОЙСТВА НАНОСТРУКТУРИРОВАННОЙ КЕРАМИКИ НА ОСНОВЕ Al2O3 УПРОЧНЕННОЙ YSZ
В проведенной работе были исследованы физико-механические свойства керамики на основе корунда, упрочненного диоксидом циркония, стабилизированным оксидом иттрия. Исследуемый материал был получен на основе механоактивированных нанодисперсных порошков данных компонентов. В работе применялись следующие давления прессования: 50, 100, 200 и 300 МПа. Полученные заготовки были спечены в высокотемпературной печи при температуре 1700 ℃ в воздушной среде. При проведении растровой электронной микроскопии с картированием элементов было установлено наличие корундовой матрицы с равномерно распределенной в ней фазы твердого раствора диоксида циркония и оксида иттрия. После спекания в исследуемых материалах наблюдалась мелкозернистая структура с преобладающим размером частиц 1-9 мкм. Было установлено, что давление 300 МПа является предельным при прессовании данных керамических шихт, при превышении которого возможно появление дефектов прессования. При данном давлении была достигнута наибольшая относительная плотность материала среди исследуемых – 85,12%. Было установлено, что при изменении давления прессования становится возможным достижение свойств материалов в широком диапазоне и адаптирование их под требуемые условия эксплуатации. Так было установлено, что при проведении спекания заготовок полученных в указанном диапазоне давлений прессования модули Юнга изменялись в пределах от 126 до 297 ГПа, а твердость индентирования от 2,25 до 7,95 ГПа.
- 31 March 2025
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 22 (1) , 85-91
Open AccessФИЗИКО-МЕХАНИЧЕСКИЕ СВОЙСТВА НАНОСТРУКТУРИРОВАННОЙ КЕРАМИКИ НА ОСНОВЕ Al2O3 УПРОЧНЕННОЙ YSZ
В проведенной работе были исследованы физико-механические свойства керамики на основе корунда, упрочненного диоксидом циркония, стабилизированным оксидом иттрия. Исследуемый материал был получен на основе механоактивированных нанодисперсных порошков данных компонентов. В работе применялись следующие давления прессования: 50, 100, 200 и 300 МПа. Полученные заготовки были спечены в высокотемпературной печи при температуре 1700 ℃ в воздушной среде. При проведении растровой электронной микроскопии с картированием элементов было установлено наличие корундовой матрицы с равномерно распределенной в ней фазы твердого раствора диоксида циркония и оксида иттрия. После спекания в исследуемых материалах наблюдалась мелкозернистая структура с преобладающим размером частиц 1-9 мкм. Было установлено, что давление 300 МПа является предельным при прессовании данных керамических шихт, при превышении которого возможно появление дефектов прессования. При данном давлении была достигнута наибольшая относительная плотность материала среди исследуемых – 85,12%. Было установлено, что при изменении давления прессования становится возможным достижение свойств материалов в широком диапазоне и адаптирование их под требуемые условия эксплуатации. Так было установлено, что при проведении спекания заготовок полученных в указанном диапазоне давлений прессования модули Юнга изменялись в пределах от 126 до 297 ГПа, а твердость индентирования от 2,25 до 7,95 ГПа.
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- No. 00,p. 42
Mechanosynthesis and solid-phase synthesis of ceramics based on hafnium and zirconium carbonitride
Ceramics based on hafnium carbonitride and zirconium carbonitride were obtained on the basis of commercial powders of hafnium and zirconium carbides and nitrides by mechanochemical synthesis during processing in a high-energy planetary ball milling, as well as solid-phase synthesis during spark plasma sintering. It was shown that with increasing processing time in a high-energy ball milling the formation of carbonitrides increases and a change in the lattice parameters characteristic of the process of carbonitride formation is observed, correlating according to Vegard's rule. When spark plasma sintering was carried out at a temperature of 2000?C, a complete solid-phase reaction with the formation of hafnium carbonitride and zirconium carbonitride was observed. It was found that the solid-phase reaction of hafnium carbonitride formation starts at a temperature of 1347?C, and zirconium carbonitride at 1562?C. Bulk samples were obtained by spark plasma sintering. The hardness, Young's modulus and fracture toughness measured on the consolidated samples were: 19.51 ? 0.22 GPa, 448.26 ? 3.41 GPa, 7.03 ? 0.26 MPa?m1/2 for HfCN; 16 ? 0.12 GPa, 343.44 ? 4.25 GPa, 3.57 ? 0.14 MPa?m1/2 for ZrCN, respectively.
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- No. 00,p. 42
Open AccessMechanosynthesis and solid-phase synthesis of ceramics based on hafnium and zirconium carbonitride
Ceramics based on hafnium carbonitride and zirconium carbonitride were obtained on the basis of commercial powders of hafnium and zirconium carbides and nitrides by mechanochemical synthesis during processing in a high-energy planetary ball milling, as well as solid-phase synthesis during spark plasma sintering. It was shown that with increasing processing time in a high-energy ball milling the formation of carbonitrides increases and a change in the lattice parameters characteristic of the process of carbonitride formation is observed, correlating according to Vegard's rule. When spark plasma sintering was carried out at a temperature of 2000?C, a complete solid-phase reaction with the formation of hafnium carbonitride and zirconium carbonitride was observed. It was found that the solid-phase reaction of hafnium carbonitride formation starts at a temperature of 1347?C, and zirconium carbonitride at 1562?C. Bulk samples were obtained by spark plasma sintering. The hardness, Young's modulus and fracture toughness measured on the consolidated samples were: 19.51 ? 0.22 GPa, 448.26 ? 3.41 GPa, 7.03 ? 0.26 MPa?m1/2 for HfCN; 16 ? 0.12 GPa, 343.44 ? 4.25 GPa, 3.57 ? 0.14 MPa?m1/2 for ZrCN, respectively.
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- Vol. 57 (4) , 469-483
Characterization and densification of hot pressed ZrCN-$ \mathrm{ZrO_2} $ ceramics
\mathrm{ZrCN-ZrO_2} ceramics were produced by hot pressing at a temperature of 2273 K, a pressure of 30 MPa, and a holding time at a given temperature of 15 minutes. Sintering was carried out in a vacuum environment. High-density \mathrm{ZrCN-ZrO_2} ceramics were manufactured using zirconium nitride and carbide powders. Zirconium dioxide acted as a sintering additive due to its lowest melting point among the studied compounds. Using scanning electron microscopy and X-ray phase analysis, the presence of zirconium carbonitride as a matrix phase with different stoichiometry, depending on the change in the initial composition of the powders, was established. An increase in strength, hardness, Young''s modulus, and crack resistance of the studied materials was observed with an increase in the content of zirconium nitride in the mixture of initial powders and a decrease in the porosity of the material. At the same time, a decrease in subgrains was recorded according to the results of X-ray phase analysis.
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- Vol. 57 (4) , 469-483
Open AccessCharacterization and densification of hot pressed ZrCN-$ \mathrm{ZrO_2} $ ceramics
\mathrm{ZrCN-ZrO_2} ceramics were produced by hot pressing at a temperature of 2273 K, a pressure of 30 MPa, and a holding time at a given temperature of 15 minutes. Sintering was carried out in a vacuum environment. High-density \mathrm{ZrCN-ZrO_2} ceramics were manufactured using zirconium nitride and carbide powders. Zirconium dioxide acted as a sintering additive due to its lowest melting point among the studied compounds. Using scanning electron microscopy and X-ray phase analysis, the presence of zirconium carbonitride as a matrix phase with different stoichiometry, depending on the change in the initial composition of the powders, was established. An increase in strength, hardness, Young''s modulus, and crack resistance of the studied materials was observed with an increase in the content of zirconium nitride in the mixture of initial powders and a decrease in the porosity of the material. At the same time, a decrease in subgrains was recorded according to the results of X-ray phase analysis.