Merve Ergün
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Merve Ergün has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Güralp Özkoç
Department of Chemistry, Istinye University, 34396 Istanbul, Türkiye
2 shared publications - Mehmet Kodal
Department of Chemical Engineering, Kocaeli University, 41001 Kocaeli, Türkiye
2 shared publications - Nazlı Yazıcı
Department of Chemical Engineering, Kocaeli University, 41001 Kocaeli, Türkiye
2 shared publications - Özgenur İnan
Polymer Science and Technology Graduate Program, Kocaeli University, 41001 Kocaeli, Türkiye
2 shared publications
Latest Publications
- Open Access
Non-Isothermal Crystallization Behavior and Crystal Morphology of EPDM/PP Thermoplastic Vulcanizates Containing TAC and OV-POSS Coagents
Ethylene propylene diene monomer rubber/polypropylene (EPDM/PP) thermoplastic vulcanizates containing triallyl cyanurate (TAC) or octavinyl polyhedral oligomeric silsesquioxane (OV-POSS) coagents were prepared by dynamic vulcanization. The effects of coagent type, loading level, and EPDM/PP ratio on non-isothermal crystallization were investigated using differential scanning calorimetry (DSC), polarized optical microscopy (POM), and X-ray diffraction (XRD). Crystallization kinetics were evaluated using the Avrami, Ozawa, and combined Avrami-Ozawa models, while nucleation activity and apparent activation energies were assessed using the Dobreva-Gutzow, Kissinger, Takhor, and Friedman approaches. Both coagents, particularly OV-POSS, shifted crystallization onset toward higher temperatures, demonstrating enhanced heterogeneous nucleation. The decreasing Avrami-derived half-times t0.5 with increasing cooling rate were qualitatively consistent with the experimental DSC half-times t1/2. The Ozawa model did not adequately describe the investigated systems, while the combined Avrami-Ozawa model provided satisfactory correlations. The influence of the coagents on the overall crystallization rate depended on composition, loading, and cooling rate. In particular, high OV-POSS loading promoted earlier nucleation but did not consistently shorten t0.5, especially in the EPDM-rich TPVs. POM revealed earlier crystal formation, increased nucleation density, and smaller spherulites in the coagent-containing samples. DSC analysis revealed an increase in PP-normalized crystallinity upon OV-POSS incorporation, while XRD confirmed an increased crystalline fraction, predominantly associated with the α-crystalline form. This effect was particularly pronounced in the PP-rich formulations. Although OV-POSS promoted heterogeneous nucleation and crystalline structure development, its influence on the overall crystallization rate remained dependent on blend composition, coagent loading, and cooling conditions, suggesting a complex interplay between nucleation and subsequent crystal growth.
Open AccessNon-Isothermal Crystallization Behavior and Crystal Morphology of EPDM/PP Thermoplastic Vulcanizates Containing TAC and OV-POSS Coagents
Ethylene propylene diene monomer rubber/polypropylene (EPDM/PP) thermoplastic vulcanizates containing triallyl cyanurate (TAC) or octavinyl polyhedral oligomeric silsesquioxane (OV-POSS) coagents were prepared by dynamic vulcanization. The effects of coagent type, loading level, and EPDM/PP ratio on non-isothermal crystallization were investigated using differential scanning calorimetry (DSC), polarized optical microscopy (POM), and X-ray diffraction (XRD). Crystallization kinetics were evaluated using the Avrami, Ozawa, and combined Avrami-Ozawa models, while nucleation activity and apparent activation energies were assessed using the Dobreva-Gutzow, Kissinger, Takhor, and Friedman approaches. Both coagents, particularly OV-POSS, shifted crystallization onset toward higher temperatures, demonstrating enhanced heterogeneous nucleation. The decreasing Avrami-derived half-times t0.5 with increasing cooling rate were qualitatively consistent with the experimental DSC half-times t1/2. The Ozawa model did not adequately describe the investigated systems, while the combined Avrami-Ozawa model provided satisfactory correlations. The influence of the coagents on the overall crystallization rate depended on composition, loading, and cooling rate. In particular, high OV-POSS loading promoted earlier nucleation but did not consistently shorten t0.5, especially in the EPDM-rich TPVs. POM revealed earlier crystal formation, increased nucleation density, and smaller spherulites in the coagent-containing samples. DSC analysis revealed an increase in PP-normalized crystallinity upon OV-POSS incorporation, while XRD confirmed an increased crystalline fraction, predominantly associated with the α-crystalline form. This effect was particularly pronounced in the PP-rich formulations. Although OV-POSS promoted heterogeneous nucleation and crystalline structure development, its influence on the overall crystallization rate remained dependent on blend composition, coagent loading, and cooling conditions, suggesting a complex interplay between nucleation and subsequent crystal growth.
- Open Access
Unlocking the Potential Use of Reactive POSS as a Coagent for EPDM/PP-Based TPV
Thermoplastic vulcanizates (TPVs) are multifunctional materials consisting of two or more phases with solid elastomeric properties at room temperatures and fluid-like properties above their melting point. They are produced through a reactive blending process known as dynamic vulcanization. The most widely produced TPV type is ethylene propylene diene monomer/polypropylene (EPDM/PP), which is the focus of this study. The peroxides are mainly selected to be used in crosslinking of EPDM/PP-based TPV. However, they still have some disadvantages, such as the side reactions resulting in the beta chain scission of the PP phase and undesired disproportionation reactions. To eliminate these disadvantages, coagents are used. In this study, for the first time, the use of vinyl functionalized polyhedral oligomeric silsesquioxane (OV-POSS) nanoparticles was investigated as a potential coagent in EPDM/PP-based TPV production via peroxide-initiated dynamic vulcanization. The properties of the TPVs having POSS were compared with the conventional TPVs containing conventional coagents, such as triallyl cyanurate (TAC). POSS content and EPDM/PP ratio were investigated as the material parameters. Mechanical properties of EPDM/PP TPVs exhibited higher values in the presence of OV-POSS, which resulted from the active participation of OV-POSS into the three-dimensional network structure of EPDM/PP during dynamic vulcanization.
Open AccessUnlocking the Potential Use of Reactive POSS as a Coagent for EPDM/PP-Based TPV
Thermoplastic vulcanizates (TPVs) are multifunctional materials consisting of two or more phases with solid elastomeric properties at room temperatures and fluid-like properties above their melting point. They are produced through a reactive blending process known as dynamic vulcanization. The most widely produced TPV type is ethylene propylene diene monomer/polypropylene (EPDM/PP), which is the focus of this study. The peroxides are mainly selected to be used in crosslinking of EPDM/PP-based TPV. However, they still have some disadvantages, such as the side reactions resulting in the beta chain scission of the PP phase and undesired disproportionation reactions. To eliminate these disadvantages, coagents are used. In this study, for the first time, the use of vinyl functionalized polyhedral oligomeric silsesquioxane (OV-POSS) nanoparticles was investigated as a potential coagent in EPDM/PP-based TPV production via peroxide-initiated dynamic vulcanization. The properties of the TPVs having POSS were compared with the conventional TPVs containing conventional coagents, such as triallyl cyanurate (TAC). POSS content and EPDM/PP ratio were investigated as the material parameters. Mechanical properties of EPDM/PP TPVs exhibited higher values in the presence of OV-POSS, which resulted from the active participation of OV-POSS into the three-dimensional network structure of EPDM/PP during dynamic vulcanization.