YJYongqiao Jin

Yongqiao Jin

*This is an algorithmically generated author record based on publicly available information.

Yongqiao Jin has a total of 8 co-authors. Here are the top co-authors by number of shared publications:

  • Qunfei Gu

    State Key Laboratory of Mechanical System and Vibration, School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China

    2 shared publications
  • Shun Liu

    State Key Laboratory of Mechanical System and Vibration, School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China

    2 shared publications
  • Yuhan Wang

    State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai, 200240, China

    2 shared publications
  • Changqi Yang

    Shanghai Hanghe Intelligent Technology Corporation, Shanghai 201699, China

    1 shared publication
  • Qingzhen Bi

    State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai, China

    1 shared publication
  • Sheng Zhao

    State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai, 200240, China

    1 shared publication

Latest Publications

  • Open Access

    Full-Space Modeling of Geometric Variation Propagation in a Multi-Axis Milling System Considering Local Parallel Chains

    by Shun Liu, Yang Xiang, Qunfei Gu, Yongqiao Jin, Sun Jin

    The end-effector accuracy of a multi-axis milling system is primarily affected by assembly errors and deformation errors induced by low structural stiffness. This accuracy exhibits spatially nonlinear and non-uniform variations with changes in system pose, especially in robotic milling systems. Therefore, full-space accuracy modeling that accounts for manufacturing and assembly processes is crucial, particularly for machining workspace optimization. However, existing assembly deviation models are generally limited to error fluctuation simulations under fixed poses and lack the capability to analyze accuracy variations across the entire motion space of kinematic mechanisms, often requiring remodeling for different poses. To address this issue, this paper proposes a full-space geometric variation propagation modeling method for multi-axis robotic machining systems, considering local parallel chains. In the proposed model, the effects of manufacturing tolerances of multiple axes and their propagation on the geometric accuracy of a multi-axis milling system are considered in the spatial domain during the milling motion process. Firstly, three-dimensional tolerance expressions of joint and shaft-hole features are defined using small displacement Torsors, which can represent small feature variations within their tolerance ranges. Then, feature-to-feature Jacobian matrices are defined to characterize geometric variation propagation in multi-axis assemblies. Consequently, an overall Jacobian–Torsor-based expression model can be generated through the construction of a dimensional chain diagram. Based on the proposed model, case studies are conducted on a multi-axis robotic milling system to validate its effectiveness in modeling geometric variation propagation. The proposed method provides a comprehensive understanding of the mechanism of geometric variation propagation in robotic milling processes.

  • Open Access

    Experimental Investigation and Modeling of Force-Induced Surface Errors for the Robot-Assisted Milling Process

    by Yongqiao Jin, Qunfei Gu, Shun Liu, Changqi Yang

    A series of experiments were performed aiming at controlling milling force-induced surface errors in the robot-assisted milling process, for the sub-area of the multi-stiffener reinforced inner wall of complex cylindrical thin-walled casting parts, to investigate the relationship between surface errors, milling forces, and robot-assisted milling parameters. Firstly, based on the design of experiments (DoE) method, milling forces and surface errors were investigated based on a series of experiments with different groups of milling parameters. Secondly, the modeling of milling forces, surface errors, and milling parameters was realized by means of response surface methodology (RSM), then the parametric expression was obtained of the robot-assisted milling process. Finally, the parameters of the milling process toward the surface error were obtained based on an evolutionary algorithm. The results show that the surface errors are different for the different milling styles of down milling and up milling. In up milling processes, the surface errors are positive, and the actual material removal amounts are generally higher than the nominal ones, while negative in down milling processes. The surface errors induced by milling forces can be effectively controlled and reduced using process optimization in the robot-assisted milling process, while maintaining relatively high milling forces and high machining efficiency. This provides theoretical support for industry applications.


  • Open Access

    Dual-Bézier path smoothing and interpolation for five-axis linear tool path in workpiece coordinate system

    by Yongqiao Jin, Qingzhen Bi, Yuhan Wang

    The tool path composed of consecutive short linear segments (G01 blocks) is still the widespread tool path representation form in five-axis machining. The inherent shortcoming of linear tool path is first-order discontinuity at the corner, which is the bottleneck to achieve high-speed and high-accuracy machining. In this article, a dual-Bézier path smoothing algorithm for five-axis linear tool path in workpiece coordinate system is proposed. There are three steps involved in our method. First, the corner error distribution model is introduced to assign the given tolerance to the smoothing approximation error constraint and the chord error constraint to ensure the interpolation trajectory error within the given tolerance. Second, segment junctions of the linear tool path in workpiece coordinate system are smoothed by double G2 continuous cubic Bézier curves. One cubic Bézier curve is used to round the corner of the tool tip point path, and the other Bézier curve is used to round the corner of the tool axis point path. This algorithm takes the conditions of approximation error constraint, the parameterized synchronization constraint, and continuous curvature constraint into consideration. Hence, the tangency and curvature continuities are both guaranteed in the new path. Third, an adaptive feedrate scheduling method is introduced to interpolate the new path. Simulation and experiment are performed to verify the effectiveness of the proposed method in five-axis tool path smoothing, speed smoothing, and trajectory accuracy controlling.