Mohammad Masafi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Masafi has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Hadi Mozaffari-Jovein
Institute of Materials Science and Engineering Tuttlingen, Furtwangen University, Kronen-Str. 16, D-78532 Tuttlingen, Germany
8 shared publications - Heinz Palkowski
Institute of Metallurgy, Clausthal University of Technology, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld, Germany
8 shared publications - Achim Conzelmann
Institute of Materials Science and Engineering Tuttlingen, Furtwangen University, Kronen-Str. 16, D-78532 Tuttlingen, Germany
4 shared publications - Mo Li
Institute of Materials Science and Engineering Tuttlingen, Furtwangen University, Kronen-Str. 16, D-78532 Tuttlingen, Germany
4 shared publications
Latest Publications
- Open Access
Advances in Microstructure Evolution, Sigma-Phase Formation, and XRD Analysis of Laser Metal Deposited 316L/430L-WC Multilayers on GJL After Brake-Shock Testing
Grey cast iron brake discs remain standard in automotive braking systems due to their favourable thermal conductivity and mechanical strength. However, increasingly stringent environmental regulations, including Euro 7, necessitate enhanced surface durability to reduce particulate emissions and mitigate corrosion-related degradation. In this context, laser metal deposition (LMD) offers a promising route to engineer wear-resistant coating systems with tailored microstructures. This study investigates phase formation and microstructural evolution in a 316L/430L-WC multilayer coating deposited on grey cast iron (GJL) brake discs and subjected to brake-shock testing to replicate thermomechanical load cycles representative of real braking conditions. X-ray diffraction (XRD) performed on the interlayer region between the 316L and 430L-WC layers revealed clear evidence of σ-phase formation, indicating intermetallic transformations facilitated by thermal cycling. Microstructural characterization using scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) identified localized enrichment of Cr- and Fe-rich regions that support the XRD-based interpretation of σ-phase development. These results provide insights into phase transformations and elemental diffusion in LMD-fabricated brake-disc coatings. The findings advance the understanding of thermally induced transformations in multilayer steel systems and support the optimization of LMD coatings for high-temperature and wear-intensive applications through advanced analytical evaluation.
Open AccessAdvances in Microstructure Evolution, Sigma-Phase Formation, and XRD Analysis of Laser Metal Deposited 316L/430L-WC Multilayers on GJL After Brake-Shock Testing
Grey cast iron brake discs remain standard in automotive braking systems due to their favourable thermal conductivity and mechanical strength. However, increasingly stringent environmental regulations, including Euro 7, necessitate enhanced surface durability to reduce particulate emissions and mitigate corrosion-related degradation. In this context, laser metal deposition (LMD) offers a promising route to engineer wear-resistant coating systems with tailored microstructures. This study investigates phase formation and microstructural evolution in a 316L/430L-WC multilayer coating deposited on grey cast iron (GJL) brake discs and subjected to brake-shock testing to replicate thermomechanical load cycles representative of real braking conditions. X-ray diffraction (XRD) performed on the interlayer region between the 316L and 430L-WC layers revealed clear evidence of σ-phase formation, indicating intermetallic transformations facilitated by thermal cycling. Microstructural characterization using scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) identified localized enrichment of Cr- and Fe-rich regions that support the XRD-based interpretation of σ-phase development. These results provide insights into phase transformations and elemental diffusion in LMD-fabricated brake-disc coatings. The findings advance the understanding of thermally induced transformations in multilayer steel systems and support the optimization of LMD coatings for high-temperature and wear-intensive applications through advanced analytical evaluation.
- Open Access
- 27 April 2026
- Published by MDPI AG in Preprints.org
Advances in Microstructure Evolution, Sigma‑Phase Formation, and XRD Analysis of Laser Metal Deposited 316L/430L‑WC Multilayers on GJL after Brake‑Shock Testing
Grey cast iron brake discs remain standard in automotive braking systems due to their favorable thermal conductivity and mechanical strength. However, increasingly stringent environmental regulations, including Euro 7, necessitate enhanced surface durability to reduce particulate emissions and mitigate corrosion‑related degradation. In this context, Laser Metal Deposition (LMD) offers a promising route to engineer wear‑resistant coating systems with tailored microstructures. This study investigates phase formation and microstructural evolution in a 316L/430L‑WC multilayer coating deposited on grey cast iron (GJL) brake discs and subjected to brake‑shock testing to replicate thermomechanical load cycles representative of real braking conditions. X‑ray diffraction (XRD) performed on the interlayer region between the 316L and 430L‑WC layers revealed clear evidence of σ‑phase formation, indicating intermetallic transformations facilitated by thermal cycling. Microstructural characterization using scanning electron microscopy (SEM) and energy‑dispersive spectroscopy (EDS) identified localized enrichment of Cr‑ and Fe‑rich regions that support the XRD‑based interpretation of σ‑phase development. These results provide insights into phase transformations and elemental diffusion in LMD‑fabricated brake‑disc coatings. The findings advance the understanding of thermally induced transformations in multilayer steel systems and support the optimization of LMD coatings for high‑temperature and wear‑intensive applications through advanced analytical evaluation.
- 27 April 2026
- Published by MDPI AG in Preprints.org
Open AccessAdvances in Microstructure Evolution, Sigma‑Phase Formation, and XRD Analysis of Laser Metal Deposited 316L/430L‑WC Multilayers on GJL after Brake‑Shock Testing
Grey cast iron brake discs remain standard in automotive braking systems due to their favorable thermal conductivity and mechanical strength. However, increasingly stringent environmental regulations, including Euro 7, necessitate enhanced surface durability to reduce particulate emissions and mitigate corrosion‑related degradation. In this context, Laser Metal Deposition (LMD) offers a promising route to engineer wear‑resistant coating systems with tailored microstructures. This study investigates phase formation and microstructural evolution in a 316L/430L‑WC multilayer coating deposited on grey cast iron (GJL) brake discs and subjected to brake‑shock testing to replicate thermomechanical load cycles representative of real braking conditions. X‑ray diffraction (XRD) performed on the interlayer region between the 316L and 430L‑WC layers revealed clear evidence of σ‑phase formation, indicating intermetallic transformations facilitated by thermal cycling. Microstructural characterization using scanning electron microscopy (SEM) and energy‑dispersive spectroscopy (EDS) identified localized enrichment of Cr‑ and Fe‑rich regions that support the XRD‑based interpretation of σ‑phase development. These results provide insights into phase transformations and elemental diffusion in LMD‑fabricated brake‑disc coatings. The findings advance the understanding of thermally induced transformations in multilayer steel systems and support the optimization of LMD coatings for high‑temperature and wear‑intensive applications through advanced analytical evaluation.
- Open Access
Laser-Deposited Multilayer Coatings for Brake Discs: Corrosion Performance of 316L/430L Systems Reinforced with WC and TiC Particles
Grey cast iron brake discs are widely used in automotive applications due to their excellent thermal and mechanical properties. However, stricter environmental regulations such as Euro 7 demand improved surface durability to reduce particulate emissions and corrosion-related failures. This study evaluates multilayer coatings fabricated by Laser Metal Deposition (LMD) as a potential solution. Two multi-layer systems were investigated: 316L + (316L + WC) and 316L + (430L + TiC), which were primarily reinforced with ceramic additives to increase wear resistance, with their influence on corrosion being critically evaluated. Electrochemical tests in 5 wt.% NaCl solution (DIN 17475) revealed that the 316L + (316L + WC) coating exhibited the lowest corrosion current density and most stable passive behavior, consistent with the inherent passivation of the austenitic 316L matrix. In contrast, the 316L + (430L + TiC) system showed localized corrosion associated with micro-galvanic interactions, despite the chemical stability of TiC particles. Post-corrosion SEM and EDS confirmed chromium depletion and chloride accumulation at corroded sites, while WC particles exhibited partial dissolution. These findings highlight that ceramic reinforcements do not inherently improve corrosion resistance and may introduce localized degradation mechanisms. Nevertheless, LMD-fabricated multilayer coatings demonstrate potential for extending brake disc service life, provided that matrix–reinforcement interactions are carefully optimized.
Open AccessLaser-Deposited Multilayer Coatings for Brake Discs: Corrosion Performance of 316L/430L Systems Reinforced with WC and TiC Particles
Grey cast iron brake discs are widely used in automotive applications due to their excellent thermal and mechanical properties. However, stricter environmental regulations such as Euro 7 demand improved surface durability to reduce particulate emissions and corrosion-related failures. This study evaluates multilayer coatings fabricated by Laser Metal Deposition (LMD) as a potential solution. Two multi-layer systems were investigated: 316L + (316L + WC) and 316L + (430L + TiC), which were primarily reinforced with ceramic additives to increase wear resistance, with their influence on corrosion being critically evaluated. Electrochemical tests in 5 wt.% NaCl solution (DIN 17475) revealed that the 316L + (316L + WC) coating exhibited the lowest corrosion current density and most stable passive behavior, consistent with the inherent passivation of the austenitic 316L matrix. In contrast, the 316L + (430L + TiC) system showed localized corrosion associated with micro-galvanic interactions, despite the chemical stability of TiC particles. Post-corrosion SEM and EDS confirmed chromium depletion and chloride accumulation at corroded sites, while WC particles exhibited partial dissolution. These findings highlight that ceramic reinforcements do not inherently improve corrosion resistance and may introduce localized degradation mechanisms. Nevertheless, LMD-fabricated multilayer coatings demonstrate potential for extending brake disc service life, provided that matrix–reinforcement interactions are carefully optimized.
- Open Access
- 28 November 2025
- Published by MDPI AG in Preprints.org
Laser-Deposited Multilayer Coatings for Brake Discs: Corrosion Performance of 316L/430L Systems Reinforced with WC and TiC Particles
Grey cast iron brake discs are widely used in automotive applications due to their excel-lent thermal and mechanical properties. However, stricter environmental regulations such as Euro 7 demand improved surface durability to reduce particulate emissions and corro-sion-related failures. This study evaluates multilayer coatings fabricated by Laser Metal Deposition (LMD) as a potential solution. Two multi-layer systems were investigated: 316L+(316L+WC) and 316L+(430L+TiC), which were primarily reinforced with ceramic additives to increase wear resistance, with their influence on corrosion being critically evaluated. Electrochemical tests in 5 wt.% NaCl solution (DIN 17475) revealed that the 316L+(316L+WC) coating exhibited the lowest corrosion current density and most stable passive behavior, consistent with the inherent passivation of the austenitic 316L matrix. In contrast, the 316L+(430L+TiC) system showed localized corrosion associated with mi-cro-galvanic interactions, despite the chemical stability of TiC particles. Post-corrosion SEM and EDS confirmed chromium depletion and chloride accumulation at corroded sites, while WC particles exhibited partial dissolution. These findings highlight that ce-ramic reinforcements do not inherently improve corrosion resistance and may introduce localized degradation mechanisms. Nevertheless, LMD-fabricated multilayer coatings demonstrate potential for extending brake disc service life, provided that matrix–reinforcement interactions are carefully optimized.
- 28 November 2025
- Published by MDPI AG in Preprints.org
Open AccessLaser-Deposited Multilayer Coatings for Brake Discs: Corrosion Performance of 316L/430L Systems Reinforced with WC and TiC Particles
Grey cast iron brake discs are widely used in automotive applications due to their excel-lent thermal and mechanical properties. However, stricter environmental regulations such as Euro 7 demand improved surface durability to reduce particulate emissions and corro-sion-related failures. This study evaluates multilayer coatings fabricated by Laser Metal Deposition (LMD) as a potential solution. Two multi-layer systems were investigated: 316L+(316L+WC) and 316L+(430L+TiC), which were primarily reinforced with ceramic additives to increase wear resistance, with their influence on corrosion being critically evaluated. Electrochemical tests in 5 wt.% NaCl solution (DIN 17475) revealed that the 316L+(316L+WC) coating exhibited the lowest corrosion current density and most stable passive behavior, consistent with the inherent passivation of the austenitic 316L matrix. In contrast, the 316L+(430L+TiC) system showed localized corrosion associated with mi-cro-galvanic interactions, despite the chemical stability of TiC particles. Post-corrosion SEM and EDS confirmed chromium depletion and chloride accumulation at corroded sites, while WC particles exhibited partial dissolution. These findings highlight that ce-ramic reinforcements do not inherently improve corrosion resistance and may introduce localized degradation mechanisms. Nevertheless, LMD-fabricated multilayer coatings demonstrate potential for extending brake disc service life, provided that matrix–reinforcement interactions are carefully optimized.
- Open Access
Microstructure Development of a Functionalized Multilayer Coating System of 316L Austenitic Steel on Grey Cast Iron Under Braking Force in a Corrosive Environment
Grey cast iron brake discs with lamellar graphite (GJL) offer excellent strength and thermal conductivity but are prone to wear and dust emissions. To mitigate these issues, a multilayer coating was applied via Laser Metal Deposition (LMD), comprising a 316L stainless steel base layer and a WC-reinforced top layer. This study examines the microstructural evolution of the coatings under simulated thermomechanical and corrosive conditions using a brake shock corrosion test. Microstructural characterization was performed via Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD), focusing on grain size, orientation, and texture before and after testing. EBSD analysis revealed significant grain coarsening, with sizes increasing from below 20 µm to 30–60 µm, and a shift toward texture. Hardness measurements showed a reduction in the WC-reinforced layer from 478 HV to 432 HV and in the 316L base layer from 232 HV to 223 HV, confirming the influence of thermomechanical stress. SEM analysis revealed a transition from horizontal cracks—caused by residual stress during LMD—to vertical microcracks propagating from the substrate, activated by braking-induced loads. These findings provide insights into the microstructural response of LMD coatings under realistic service conditions and underscore the importance of grain boundary control in designing durable brake disc systems.
Open AccessMicrostructure Development of a Functionalized Multilayer Coating System of 316L Austenitic Steel on Grey Cast Iron Under Braking Force in a Corrosive Environment
Grey cast iron brake discs with lamellar graphite (GJL) offer excellent strength and thermal conductivity but are prone to wear and dust emissions. To mitigate these issues, a multilayer coating was applied via Laser Metal Deposition (LMD), comprising a 316L stainless steel base layer and a WC-reinforced top layer. This study examines the microstructural evolution of the coatings under simulated thermomechanical and corrosive conditions using a brake shock corrosion test. Microstructural characterization was performed via Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD), focusing on grain size, orientation, and texture before and after testing. EBSD analysis revealed significant grain coarsening, with sizes increasing from below 20 µm to 30–60 µm, and a shift toward texture. Hardness measurements showed a reduction in the WC-reinforced layer from 478 HV to 432 HV and in the 316L base layer from 232 HV to 223 HV, confirming the influence of thermomechanical stress. SEM analysis revealed a transition from horizontal cracks—caused by residual stress during LMD—to vertical microcracks propagating from the substrate, activated by braking-induced loads. These findings provide insights into the microstructural response of LMD coatings under realistic service conditions and underscore the importance of grain boundary control in designing durable brake disc systems.
- Open Access
- 24 June 2025
- Published by MDPI AG in Preprints.org
Microstructure Development of a Functionalized Multilayer Coating System of 316l Austenitic Steel on Grey Cast Iron Under Braking Force in a Corrosive Environment
Brake discs made of grey cast iron with lamellar graphite (GJL) offer an excellent combination of strength and thermal conductivity, which is essential for the high demands on braking performance and durability in the automotive industry. However, the resulting dust emissions are a disadvantage that can be mitigated by applying a wear‐resistant coating on the brake disc using the Laser Metal Deposition (LMD) process. In this study, the influence of the braking force on the microstructure of the coated brake disc in a corrosive environment was investigated. The surface of grey cast iron brake discs was functionalized with 316L stainless steel, which was partially reinforced with tungsten carbide particles using the LMD process.The main objective is to improve the wear and corrosion resistance of brake discs under operating conditions. The samples were subjected to a brake shock corrosion test, which simulates real thermal and mechanical loads. Microstructural analysis was performed using Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD) to evaluate microstructural features such as grain size, grain orientation and phase distribution before and after the brake shock corrosion test. The study highlights the critical importance of understanding thermal effects and microstructural changes to optimize brake performance and ensure safety.The most important results include the promotion of grain growth, crystal reorientation and texture changes through thermal and mechanical alternating stress as well as the improvement of wear resistance through the incorporation of tungsten carbide particles in stainless steel.
- 24 June 2025
- Published by MDPI AG in Preprints.org
Open AccessMicrostructure Development of a Functionalized Multilayer Coating System of 316l Austenitic Steel on Grey Cast Iron Under Braking Force in a Corrosive Environment
Brake discs made of grey cast iron with lamellar graphite (GJL) offer an excellent combination of strength and thermal conductivity, which is essential for the high demands on braking performance and durability in the automotive industry. However, the resulting dust emissions are a disadvantage that can be mitigated by applying a wear‐resistant coating on the brake disc using the Laser Metal Deposition (LMD) process. In this study, the influence of the braking force on the microstructure of the coated brake disc in a corrosive environment was investigated. The surface of grey cast iron brake discs was functionalized with 316L stainless steel, which was partially reinforced with tungsten carbide particles using the LMD process.The main objective is to improve the wear and corrosion resistance of brake discs under operating conditions. The samples were subjected to a brake shock corrosion test, which simulates real thermal and mechanical loads. Microstructural analysis was performed using Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD) to evaluate microstructural features such as grain size, grain orientation and phase distribution before and after the brake shock corrosion test. The study highlights the critical importance of understanding thermal effects and microstructural changes to optimize brake performance and ensure safety.The most important results include the promotion of grain growth, crystal reorientation and texture changes through thermal and mechanical alternating stress as well as the improvement of wear resistance through the incorporation of tungsten carbide particles in stainless steel.
- Open Access
- 1 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 6090-6101
Micro-friction mechanism characterization of particle-reinforced multilayer systems of 316L and 430L alloys on grey cast iron
- 1 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 6090-6101
Open AccessMicro-friction mechanism characterization of particle-reinforced multilayer systems of 316L and 430L alloys on grey cast iron
- Open Access
Microstructural Properties of Particle-Reinforced Multilayer Systems of 316L and 430L Alloys on Gray Cast Iron
Gray cast iron (GJL) is known for its excellent damping property and high thermal conductivity, thanks to its unique lamellar graphite and pearlite structure. In a recent study, laser metal deposition (LMD) was explored as a potential process to enhance the corrosion resistance and wear mechanism of this tribological system. The focus was on laser cladding of gray cast iron using two different of stainless-steel materials, namely 430L and 316L, combined with TiC and WC particles. To create the samples, a multilayer coating system was employed. A comparative analysis of the microstructures was performed to understand the interaction of the laser beam with the material (composite materials). Surface properties were then characterized using light microscopy and electron microscopy (SEM) before and after subjecting the samples to a shock corrosion test, simulating automotive conditions. Additionally, phase analyses were performed at the interfaces between the coatings and the substrate, with particular attention given to the behavior of the graphite lamellae at these interfaces. This study aims to provide valuable insights into the potential improvements that can be achieved through laser cladding on gray cast iron, specifically in terms of corrosion resistance and wear mechanisms. By analyzing the microstructures and surface properties, researchers can gain a better understanding of the performance and durability of the coated samples.
Open AccessMicrostructural Properties of Particle-Reinforced Multilayer Systems of 316L and 430L Alloys on Gray Cast Iron
Gray cast iron (GJL) is known for its excellent damping property and high thermal conductivity, thanks to its unique lamellar graphite and pearlite structure. In a recent study, laser metal deposition (LMD) was explored as a potential process to enhance the corrosion resistance and wear mechanism of this tribological system. The focus was on laser cladding of gray cast iron using two different of stainless-steel materials, namely 430L and 316L, combined with TiC and WC particles. To create the samples, a multilayer coating system was employed. A comparative analysis of the microstructures was performed to understand the interaction of the laser beam with the material (composite materials). Surface properties were then characterized using light microscopy and electron microscopy (SEM) before and after subjecting the samples to a shock corrosion test, simulating automotive conditions. Additionally, phase analyses were performed at the interfaces between the coatings and the substrate, with particular attention given to the behavior of the graphite lamellae at these interfaces. This study aims to provide valuable insights into the potential improvements that can be achieved through laser cladding on gray cast iron, specifically in terms of corrosion resistance and wear mechanisms. By analyzing the microstructures and surface properties, researchers can gain a better understanding of the performance and durability of the coated samples.