ZZZhenye Zhao

Zhenye Zhao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zhenye Zhao has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Ultrasonic-Assisted Spinning V-Groove Moulding Mechanism and Accuracy Research

    by Shiqi Chen, Weiqing Wang, Qingshan Jiang, Jiashun Gao, Yongqing Lai, Yuhong Liu, Zhilong Xu, Zhenye Zhao

    Spinning forming, a new method for processing multi-ribbed pulleys, is increasingly replacing traditional casting and cutting techniques. However, reducing the substantial forming load remains a challenging task. This paper explores the introduction of ultrasonic assistance into the spinning process to examine the V-groove formation in multi-ribbed pulleys and combines experimental spinning trials with finite element analysis (FEA) to investigate the process. It assesses how ultrasonic aid affects spinning quality under various static loads by analysing V-groove depth, inclination angle, microhardness, structure, and surface roughness. The results indicate that ultrasonic assistance significantly increases the depth of the V-groove in spinning formation. Initially, the V-groove depth is 197.64 μm, which improves to 410.35 μm with ultrasonic aid, corresponding to a reduction in static load by 185 N. The V-groove angle rises with static load, but with ultrasonic assistance, the angle stabilises, enhancing forming accuracy. At a static load of 700 N, the V-groove angle decreases from 74.32° to 62.96°.


  • Open Access

    A Micro-Topography Measurement and Compensation Method for the Key Component Surface Based on White-Light Interferometry

    by Junying Chen, Boxuan Wang, Xiuyu Chen, Qingshan Jiang, Wei Feng, Zhilong Xu, Zhenye Zhao

    The grinding grooves of material removal machining and the residues of a machining tool on the key component surface cause surface stress concentration. Thus, it is critical to carry out precise measurements on the key component surface to evaluate the stress concentration. Based on white-light interferometry (WLI), we studied the measurement distortion caused by the reflected light from the steep side of the grinding groove being unable to return to the optical system for imaging. A threshold value was set to eliminate the distorted measurement points, and the cubic spline algorithm was used to interpolate the eliminated points for compensation. The compensation result agrees well with the atomic force microscope (AFM) measurement result. However, for residues on the surface, a practical method was established to obtain a microscopic 3D micro-topography point cloud and a super-depth-of-field fusion image simultaneously. Afterward, the semantic segmentation network U-net was adopted to identify the residues in the super-depth-of-field fusion image and achieved a recognition accuracy of 91.06% for residual identification. Residual feature information, including height, position, and size, was obtained by integrating the information from point clouds and super-depth-of-field fusion images. This work can provide foundational data to study surface stress concentration.


  • Open Access

    The Effects of Ultrasonic Impact Modification on the Surface Quality of 20CrNiMo Carburized Steel

    by Qingshan Jiang, Li Zhu, Junying Chen, Xiuyu Chen, Jianchun Weng, Zhilong Xu, Zhenye Zhao

    Ultra-high residual compressive stress can be introduced via the ultrasonic impact on the basis of transformation hardening, and further enhance the overall performance of 20CrNiMo carburized steel. In order to achieve the best surface quality of 20CrNiMo carburized steel, ultrasonic impact modification testing with varying static loads (900 N, 1200 N, and 1500 N) and rounds (1, 3, and 6) was conducted. By characterizing microhardness, microstructure, the surface roughness and residual compressive stress, the influence of ultrasonic impact modification parameters on its surface quality were analyzed. The experimental results indicated that the static loads and rounds of ultrasonic impact modification had a significant impact on the surface quality. The best surface quality could be obtained after six rounds of ultrasonic impact modification under a static load of 1200 N. In addition, the surface roughness decreased from 0.40 μm to 0.04 μm, the surface microhardness increased from 679 HV0.1 to 1086 HV0.1, and the maximum residual compressive stress of 1195.36 MPa was formed. Furthermore, the surface quality would deteriorate when the static load and ultrasonic impact rounds were increased.


  • Open Access

    Effect of Laser Shock Peening on the Fatigue Life of 1Cr12Ni3Mo2VN Steel for Steam Turbine Blades

    by Zhuolin Tang, Jiashun Gao, Zhilong Xu, Bicheng Guo, Qingshan Jiang, Xiuyu Chen, Jianchun Weng, Bo Li, Junying Chen, Zhenye Zhao

    In the present study, laser shock peening (LSP) was employed to enhance the rotating bending fatigue life of 1Cr12Ni3Mo2VN martensitic stainless steel used in steam turbine blades, addressing the issue of insufficient fatigue performance in these components. The aim of this study was to investigate the effect of LSP on the microhardness, residual stress, and rotating bending fatigue life of 1Cr12Ni3Mo2VN steel samples. The microhardness of LSP-treated samples was increased by 10.5% (LSP-3J sample) and 15.3% (LSP-4J sample), respectively, compared to high-frequency hardening samples. The residual compressive stress of the LSP-4J sample was the largest, reaching −689 MPa, and the affected layer depth was about 800 μm. Fatigue tests showed that the number of cycles at the fracture point for the LSP-3J and LSP-4J samples increased by 163% and 233%, respectively. The fatigue fracture morphology of the four samples showed that the microhardness and residual compressive stress distribution introduced by LSP could effectively inhibit the initiation of surface cracks, slow down the crack growth rate, and improve the rotating bending fatigue life of 1Cr12Ni3Mo2VN.


  • Open Access

    The Effects of High-Energy Composite Surface Layer Modification on the Impact Performance of the H13 Steel Cutter Ring for Shield Tunneling Machine

    by Huanbin Xu, Yi Li, Zhilong Xu, Jun Cheng, Xiuyu Chen, Qingshan Jiang, Junying Chen, Zhenye Zhao

    The service life of the cutter ring of the shield tunneling machine affects the efficiency and cost of its tunneling. However, traditional heat treatment processes cannot simultaneously optimize both impact toughness and surface hardness, often leading to cracks or excessive wear of the cutter ring, greatly reducing their service life. According to the above situation, this paper applies high-energy composite modification treatment to H13 steel samples commonly used for the cutter ring of the hob and analyzes the impact toughness, hardness, microstructure, residual stress, and morphology characteristics of fracture of the samples under different high-energy composite modification processes. The study also investigates the effects of high-energy composite modification processes on the hardness and impact toughness of the samples. The experimental results show that the high-energy composite modification process enables the specimens to have good impact toughness and surface hardness simultaneously. The H13 steel sample has the best performance after carburizing, quenching, and laser shock modification, with a maximum surface hardness of 1017.5HV0.2 and an impact toughness of 15.64 J/cm2. Laser shock modification improves the surface residual compressive stress and hardness of H13 steel samples and also improves their impact toughness.