Yurui Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yurui Han has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Bingsheng Li
State Key Laboratory of Integrated Optoelectronics, and Key Laboratory of UV Light Emitting Materials and Technology of Ministry of Education, School of Physics, Northeast Normal University 1 , Changchun 130024
7 shared publications - Aidong Shen
Department of Electrical Engineering, The City College of New York, New York, NY, USA
6 shared publications - Yichun Liu
State Key Laboratory of Integrated Optoelectronics, and Key Laboratory of UV Light Emitting Materials and Technology of Ministry of Education, School of Physics, Northeast Normal University 1 , Changchun 130024
6 shared publications Weizhe Cui
State Key Laboratory of Integrated Optoelectronics, and Key Laboratory of UV Light Emitting Materials and Technology of Ministry of Education, School of Physics, Northeast Normal University 1 , Changchun 130024
5 shared publications- Chong Gao
Jilin Provincial Key Laboratory of Wide Bandgap Semiconductor Material Growth and Device Applications, Jilin Normal University 3 , Changchun 130103
4 shared publications - Rongpeng Fu
State Key Laboratory of Integrated Optoelectronics, and Key Laboratory of UV Light Emitting Materials and Technology of Ministry of Education, School of Physics, Northeast Normal University 1 , Changchun 130024
4 shared publications
Latest Publications
- 31 July 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (3)
MOCVD growth of (AlxGa1−x)2O3 (x = 0–0.77) alloyed films for deep UV photodetection applications
(AlxGa1−x)2O3 alloy thin films with the tuning bandgap in a range of 4.95–6.26 eV have been achieved by adjusting the Al composition (x ≈ 0–0.77) grown on a c-plane sapphire substrate via metal-organic chemical vapor deposition. With the increase in the bandgap, the fabricated metal–semiconductor–metal (MSM) photodetectors exhibit a gradual blueshift of the spectral response wavelengths from 250 to 198 nm. X-ray diffraction characterization results indicated that the crystal structure of the films transformed from a single monoclinic β-phase (x ≤ 0.57) to a β/γ dual-phase coexistence state (x ∼ 0.67–0.77) with increasing Al composition. The optimal surface morphology and crystalline quality of the films were obtained at an Al composition of 0.20. Combined with the valence-band x-ray photoelectron spectroscopy and bandgap analysis results, it is found that the introduction of Al causes an upward shift of the conduction band minimum relative to the Fermi level, which is consistent with the observed increase in the optical bandgap and blueshift of the spectral response edge. Oxygen vacancy (VO) analysis demonstrates that the VO defect concentration first decreases and then increases with increasing Al composition. Based on these results, the evolution mechanism of VO defects is elucidated, and their intrinsic correlations with lattice strain, phase transition, and thin-film crystalline quality are discussed. The fabricated MSM photodetectors exhibited an excellent comprehensive performance at a bias of 10 V, with the dark current below 10 fA, the specific detectivity of 6.58 × 1014 Jones, and the UV-visible rejection ratio as high as 9.07 × 107. Under 185 nm illumination, the photocurrent to dark current ratio of the device with a high Al composition (x = 0.77) still remains around 1.18 × 102, indicating its excellent detection sensitivity and anti-interference capability in the deep ultraviolet to vacuum ultraviolet wavebands.
- 31 July 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (3)
MOCVD growth of (AlxGa1−x)2O3 (x = 0–0.77) alloyed films for deep UV photodetection applications
(AlxGa1−x)2O3 alloy thin films with the tuning bandgap in a range of 4.95–6.26 eV have been achieved by adjusting the Al composition (x ≈ 0–0.77) grown on a c-plane sapphire substrate via metal-organic chemical vapor deposition. With the increase in the bandgap, the fabricated metal–semiconductor–metal (MSM) photodetectors exhibit a gradual blueshift of the spectral response wavelengths from 250 to 198 nm. X-ray diffraction characterization results indicated that the crystal structure of the films transformed from a single monoclinic β-phase (x ≤ 0.57) to a β/γ dual-phase coexistence state (x ∼ 0.67–0.77) with increasing Al composition. The optimal surface morphology and crystalline quality of the films were obtained at an Al composition of 0.20. Combined with the valence-band x-ray photoelectron spectroscopy and bandgap analysis results, it is found that the introduction of Al causes an upward shift of the conduction band minimum relative to the Fermi level, which is consistent with the observed increase in the optical bandgap and blueshift of the spectral response edge. Oxygen vacancy (VO) analysis demonstrates that the VO defect concentration first decreases and then increases with increasing Al composition. Based on these results, the evolution mechanism of VO defects is elucidated, and their intrinsic correlations with lattice strain, phase transition, and thin-film crystalline quality are discussed. The fabricated MSM photodetectors exhibited an excellent comprehensive performance at a bias of 10 V, with the dark current below 10 fA, the specific detectivity of 6.58 × 1014 Jones, and the UV-visible rejection ratio as high as 9.07 × 107. Under 185 nm illumination, the photocurrent to dark current ratio of the device with a high Al composition (x = 0.77) still remains around 1.18 × 102, indicating its excellent detection sensitivity and anti-interference capability in the deep ultraviolet to vacuum ultraviolet wavebands.
- 1 April 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (2)
Self-powered p/Ga2O3/GaN p–i–n ultraviolet photodetector with a composite material made of polypyrrole (PPy) and nitrogen-doped graphene (PGr) as the P-region
A PPy/PGr/Ga2O3/GaN p–i–n heterojunction ultraviolet photodetector (UV PD) with polypyrrole (PPy) and nitrogen-doped graphene (PGr) combined as the p-region was fabricated, in which β-Ga2O3 was synthesized by substituting oxygen atoms for nitrogen atoms in the top layer of the GaN matrix at high temperature. In the self-powered mode, the device exhibits bimodal responses in the UVC–UVA bands. Compared with the single-peak response of the previously reported Ga2O3/GaN structure, the spectral response range has been greatly extended. In the UVC band, the responsivity reaches 36.4 mA/W, which is 21.4 times that of the unmodified device. The detectivity was improved to 1.5 × 1011 Jones, showing an 11.3-fold enhancement. It also exhibits fast photoresponse characteristics (rise/fall times of 0.09/10.8 ms, respectively). The significant improvement of device performance is mainly attributed to the effective modification of carrier transport by PPy and PGr, which not only increases the built-in electric field at the Ga2O3/GaN interface but also significantly suppresses carrier recombination. The design strategy proposed in this study, based on the synergistic incorporation of organic polymers and two-dimensional materials, provides new ideas and technical references for the development of ultraviolet photodetectors with high sensitivity and broad and fast spectral response.
- 1 April 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (2)
Self-powered p/Ga2O3/GaN p–i–n ultraviolet photodetector with a composite material made of polypyrrole (PPy) and nitrogen-doped graphene (PGr) as the P-region
A PPy/PGr/Ga2O3/GaN p–i–n heterojunction ultraviolet photodetector (UV PD) with polypyrrole (PPy) and nitrogen-doped graphene (PGr) combined as the p-region was fabricated, in which β-Ga2O3 was synthesized by substituting oxygen atoms for nitrogen atoms in the top layer of the GaN matrix at high temperature. In the self-powered mode, the device exhibits bimodal responses in the UVC–UVA bands. Compared with the single-peak response of the previously reported Ga2O3/GaN structure, the spectral response range has been greatly extended. In the UVC band, the responsivity reaches 36.4 mA/W, which is 21.4 times that of the unmodified device. The detectivity was improved to 1.5 × 1011 Jones, showing an 11.3-fold enhancement. It also exhibits fast photoresponse characteristics (rise/fall times of 0.09/10.8 ms, respectively). The significant improvement of device performance is mainly attributed to the effective modification of carrier transport by PPy and PGr, which not only increases the built-in electric field at the Ga2O3/GaN interface but also significantly suppresses carrier recombination. The design strategy proposed in this study, based on the synergistic incorporation of organic polymers and two-dimensional materials, provides new ideas and technical references for the development of ultraviolet photodetectors with high sensitivity and broad and fast spectral response.
- Open Access
- 1 February 2026
- Published by AIP Publishing in AIP Advances
- Vol. 16 (2)
The effect of crystal quality on persistent photoconductivity in β -Ga2O3 photodetectors
Gallium oxide (Ga2O3) thin films were prepared using the metal organic chemical vapor deposition method, and photoconductive photodetectors were constructed. The results showed that with the increase in growth temperature, the grain size of Ga2O3 increased and the surface smoothness improved significantly. The full width at half maxima of the rocking curve decreases with the increase in growth temperature, indicating an improvement in crystal quality. The photoluminescence spectra of all films extend from ultraviolet (UV) to visible light. The responsivity of the fabricated photoconductive devices exceeds 5 A/W, with a maximum detectivity reaching ∼2 × 1015 Jones. The photoresponse spectrum is located in the solar-blind UV range, exhibiting excellent spectral selectivity. All devices exhibit significant photoconductive relaxation phenomena. The variations of these parameters are related to self-trapped holes (STHs) and defect-trapped holes within the material. Since STHs are an inherent characteristic of oxide semiconductors, they cannot be completely eliminated. The persistent photoconductivity effect can only be eliminated through external excitation.
- 1 February 2026
- Published by AIP Publishing in AIP Advances
- Vol. 16 (2)
Open AccessThe effect of crystal quality on persistent photoconductivity in β -Ga2O3 photodetectors
Gallium oxide (Ga2O3) thin films were prepared using the metal organic chemical vapor deposition method, and photoconductive photodetectors were constructed. The results showed that with the increase in growth temperature, the grain size of Ga2O3 increased and the surface smoothness improved significantly. The full width at half maxima of the rocking curve decreases with the increase in growth temperature, indicating an improvement in crystal quality. The photoluminescence spectra of all films extend from ultraviolet (UV) to visible light. The responsivity of the fabricated photoconductive devices exceeds 5 A/W, with a maximum detectivity reaching ∼2 × 1015 Jones. The photoresponse spectrum is located in the solar-blind UV range, exhibiting excellent spectral selectivity. All devices exhibit significant photoconductive relaxation phenomena. The variations of these parameters are related to self-trapped holes (STHs) and defect-trapped holes within the material. Since STHs are an inherent characteristic of oxide semiconductors, they cannot be completely eliminated. The persistent photoconductivity effect can only be eliminated through external excitation.
- 7 January 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (1)
MOCVD-grown α-Ga2O3 with increased growth rate and improved crystal quality for deep UV optoelectronics application
α-Ga2O3 films with a more than threefold increase in growth rate were epitaxially grown on m-Al2O3 at 530 °C by employing a 700 °C high-temperature buffer layer (HTBL) in metal–organic chemical vapor deposition growth. The underlying mechanism of the enhanced growth was understood experimentally by the surface analysis and theoretically by a model based on Gibbs–Thomson equation and first-principles calculations. With HTBL, the crystal quality of the α-Ga2O3 was also significantly improved, as evidenced by the decreased x-ray diffraction rocking curve linewidth of the (303¯0) peak. The linewidth is down to 0.387°, which is significantly narrower than 0.592° from sample without HTBL. The surface morphology of HTBL features larger, more sparsely distributed islands, resulting in a lower chemical potential on the surface, which promotes the adsorption of Ga2O3-clusters by reducing the desorption and thus increases the growth. x-ray photoelectron spectroscopy showed more oxygen vacancies (Vo) on the HTBL surface. First-principles calculations indicated that Vo in the (303¯0)-surface reduced the adsorption energy from −5.48 to −6.61 eV, thereby promoting cluster adsorption. A solar-blind ultraviolet photodetector based-on α-Ga2O3 exhibited an ultra-low dark current of 0.1 pA at 10 V, a high light-to-dark current ratio of 106, a responsivity of 0.54 A/W, and a detectivity of 5.5 × 1012 Jones.
- 7 January 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (1)
MOCVD-grown α-Ga2O3 with increased growth rate and improved crystal quality for deep UV optoelectronics application
α-Ga2O3 films with a more than threefold increase in growth rate were epitaxially grown on m-Al2O3 at 530 °C by employing a 700 °C high-temperature buffer layer (HTBL) in metal–organic chemical vapor deposition growth. The underlying mechanism of the enhanced growth was understood experimentally by the surface analysis and theoretically by a model based on Gibbs–Thomson equation and first-principles calculations. With HTBL, the crystal quality of the α-Ga2O3 was also significantly improved, as evidenced by the decreased x-ray diffraction rocking curve linewidth of the (303¯0) peak. The linewidth is down to 0.387°, which is significantly narrower than 0.592° from sample without HTBL. The surface morphology of HTBL features larger, more sparsely distributed islands, resulting in a lower chemical potential on the surface, which promotes the adsorption of Ga2O3-clusters by reducing the desorption and thus increases the growth. x-ray photoelectron spectroscopy showed more oxygen vacancies (Vo) on the HTBL surface. First-principles calculations indicated that Vo in the (303¯0)-surface reduced the adsorption energy from −5.48 to −6.61 eV, thereby promoting cluster adsorption. A solar-blind ultraviolet photodetector based-on α-Ga2O3 exhibited an ultra-low dark current of 0.1 pA at 10 V, a high light-to-dark current ratio of 106, a responsivity of 0.54 A/W, and a detectivity of 5.5 × 1012 Jones.
- 21 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (7) , 1083-1086
Bias-Tuned Selective Spectral Response High-Performance Ga₂O₃/GaN Heterojunction Ultraviolet Photodetector
β-Ga2O3 films were successfully fabricated using the GaN thermal oxidation method, and Ga2O3/GaN heterojunction ultraviolet photodetectors were constructed with varying electrode parameters, including length, width, and electrode spacing. Under optimized electrode parameters, the detector demonstrates an exceptionally low dark current, with a value of just 63.2 fA at a 10V bias. Under 33 μW/cm² ultraviolet light illumination, the detector demonstrates a high light-to-dark current ratio exceeding 10⁶. By adjusting the thickness of the β-Ga2O3 light-absorbing layer to enhance ultraviolet light absorption and reduce carrier recombination, the detector achieves a responsivity of up to 3061 A/W and a detectivity exceeding 1015 Jones. Additionally, by tuning the applied bias, the detector enables adjustable control over both the solar-blind ultraviolet single-band and solar-blind-near ultraviolet dual-band response spectra. These research findings provide important theoretical support and experimental basis for the optimized design and application of high-performance ultraviolet photodetectors.
- 21 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (7) , 1083-1086
Bias-Tuned Selective Spectral Response High-Performance Ga₂O₃/GaN Heterojunction Ultraviolet Photodetector
β-Ga2O3 films were successfully fabricated using the GaN thermal oxidation method, and Ga2O3/GaN heterojunction ultraviolet photodetectors were constructed with varying electrode parameters, including length, width, and electrode spacing. Under optimized electrode parameters, the detector demonstrates an exceptionally low dark current, with a value of just 63.2 fA at a 10V bias. Under 33 μW/cm² ultraviolet light illumination, the detector demonstrates a high light-to-dark current ratio exceeding 10⁶. By adjusting the thickness of the β-Ga2O3 light-absorbing layer to enhance ultraviolet light absorption and reduce carrier recombination, the detector achieves a responsivity of up to 3061 A/W and a detectivity exceeding 1015 Jones. Additionally, by tuning the applied bias, the detector enables adjustable control over both the solar-blind ultraviolet single-band and solar-blind-near ultraviolet dual-band response spectra. These research findings provide important theoretical support and experimental basis for the optimized design and application of high-performance ultraviolet photodetectors.
- Open Access
- 21 August 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (8)
Performance optimization of self-powered deep ultraviolet photodetector based on PEDOT:PSS/SnO2 organic/inorganic p–n heterojunction by embedding a nitrogen-doped graphene
A self-powered organic–inorganic p–n heterojunction deep ultraviolet (DUV) photodetector (PD) was fabricated based on the polymer poly(3,4-ethylene-dioxythiophene):polystyrene sulfonate (PEDOT:PSS), with an in situ transferred composite film PEDOT:PSS-nitrogen-doped graphene (NGr)-coated SnO2 microwire. At 0 V bias, the responsivity spectra of these two heterojunction PDs both had a broadband response in the range of 200–400 nm. The introduction of NGr helped to reduce the surface state of SnO2 and improve the shortwave response, resulting in a blue shift of peak position from 280 to 250 nm. Compared with PEDOT:PSS/SnO2 PD, the light–dark current ratio of the PEDOT:PSS-NGr/SnO2 PD was improved three orders of magnitude from 24.76 to 2.51 × 104; the detectivity was increased by 40 times from 1.45 × 1011 to 5.85 × 1012 Jones; and the response speed was accelerated to less than 1 s (with rise and decay times of 0.35 and 0.14 s, respectively). The performance improvement was attributed to the intermediate layer NGr forming a heterojunction with SnO2, which broadened the depletion layer of PEDOT:PSS/SnO2 and increased the strength of the built-in electric field, thereby reducing carrier recombination and boosting the response speed. These findings indicate that introducing NGr is an effective way to modify detector performance.
- 21 August 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (8)
Open AccessPerformance optimization of self-powered deep ultraviolet photodetector based on PEDOT:PSS/SnO2 organic/inorganic p–n heterojunction by embedding a nitrogen-doped graphene
A self-powered organic–inorganic p–n heterojunction deep ultraviolet (DUV) photodetector (PD) was fabricated based on the polymer poly(3,4-ethylene-dioxythiophene):polystyrene sulfonate (PEDOT:PSS), with an in situ transferred composite film PEDOT:PSS-nitrogen-doped graphene (NGr)-coated SnO2 microwire. At 0 V bias, the responsivity spectra of these two heterojunction PDs both had a broadband response in the range of 200–400 nm. The introduction of NGr helped to reduce the surface state of SnO2 and improve the shortwave response, resulting in a blue shift of peak position from 280 to 250 nm. Compared with PEDOT:PSS/SnO2 PD, the light–dark current ratio of the PEDOT:PSS-NGr/SnO2 PD was improved three orders of magnitude from 24.76 to 2.51 × 104; the detectivity was increased by 40 times from 1.45 × 1011 to 5.85 × 1012 Jones; and the response speed was accelerated to less than 1 s (with rise and decay times of 0.35 and 0.14 s, respectively). The performance improvement was attributed to the intermediate layer NGr forming a heterojunction with SnO2, which broadened the depletion layer of PEDOT:PSS/SnO2 and increased the strength of the built-in electric field, thereby reducing carrier recombination and boosting the response speed. These findings indicate that introducing NGr is an effective way to modify detector performance.