YWYuhang Wang

Yuhang Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yuhang Wang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    An IR-RIME-SQP-Based Spectrum Modification Method for Shallow Surface Electromagnetic Detection Transmitting Scheme of Metal Traps in Forested Areas

    by Zeyu An, Xiaoyue Fan, Yuhang Wang, Tao Zhang

    In the electromagnetic detection of shallow subsurface metal snaring traps in forested areas, conventional transmission schemes such as square waves, PRBS and PSO waveforms inevitably excite severe clutter in soils exhibiting viscous remanent magnetization (VRM), which drastically degrades the signal-to-clutter ratio (SCR). To resolve this issue, this paper proposes a spectrum modification method for the transmitting scheme based on an Interval Robust hybrid RIME and Sequential Quadratic Programming (IR-RIME-SQP) algorithm. By coupling the Debye relaxation characteristics of ferromagnetic targets with the soil VRM model, the proposed method concentrates limited transmission energy into a bell-shaped frequency window near the target’s characteristic frequency. Furthermore, interval analysis is introduced to ensure robust performance against the dynamic drift of coil parameters. The feasibility of this novel transmitting scheme is validated through ablation experiments and comparative simulations. Finally, laboratory measurements demonstrate that IR-RIME-SQP provides a more rational and efficient energy allocation strategy, improving the targeted frequency energy retention (TFER) by approximately 16.4% and thereby enhancing both detection efficiency and precision.

  • Open Access

    Development of a Microheater with a Large Heating Area and Low Thermal Stress in the Heating Area

    by Tao Zhang, Zequan Pan, Chunhua Zhang, Liuguang Xiong, Chunmei Yang, Jian Zhang, Mengjiao Shi, Yuhang Wang, Wen Qu

    In this paper, a microheater that can absorb thermal stress and has a large heating area is demonstrated by optimizing the structure and process of the microheater. Four symmetrically distributed elongated support beam structures were machined around the microheater via deep silicon etching. This design efficiently mitigates the deformation of the heated region caused by thermal expansion and enhances the structural stability of the microheater. The updated microheater no longer converts the work area into a thin film; instead, it creates a stable heating platform that can uniformly heat a work area measuring 10 × 10 mm2. The microheater is verified to have high temperature uniformity and structural stability in finite element simulation. Finally, thorough investigations of electrical–thermal–structural characterization were conducted. The test findings show that the new microheater can achieve 350 °C with a power consumption of 6 W and a thermal reaction time of 22 s. A scan of its whole plane reveals that the surface of the working area of the new microheater is flat and does not distort in response to variations in temperature, offering good structural stability.


  • Open Access

    A Study on Refraction Error Compensation Method for Underwater Spinning Laser Scanning Three-Dimensional Imaging

    by Jinghui Zhang, Yuhang Wang, Tao Zhang, Kai Yang, Jian Zhang, Xinyu Wang

    Laser scanning 3D imaging technology, because it can obtain accurate three-dimensional surface data, has been widely used in the search for wrecks and rescue operations, underwater resource development, and other fields. At present, the conventional underwater spinning laser scanning imaging system maintains a relatively fixed light window. However, in low-light situations underwater, the rotation of the scanning device causes some degree of water fluctuation, which warps the light strip data that the system sensor receives about the object’s surface. To solve this problem, this research studies an underwater 3D scanning and imaging system that makes use of a fixed light window and a spinning laser (FWLS). A refraction error compensation algorithm is investigated that is based on the fundamentals of linear laser scanning imaging, and a dynamic refraction mathematical model is established based on the motion of the imaging device. The results of the experiment on error analysis in an optimal underwater environment indicate that the error in reconstructing the radius is decreased by 60% (from 2.5 mm to around 1 mm) when compensating for the measurement data of a standard sphere with a radius of 20 mm. Moreover, the compensated point cloud data exhibit a higher degree of correspondence with the model of the standard spherical point cloud. Furthermore, we examine the impact of physical noise, measurement distance, and partial occlusion of the object on the imaging system inside an authentic underwater setting. This study is a good starting point for looking at the refractive error of an underwater laser scanning imaging system. It also provides to us some ideas for future research on the refractive error of other scanning imaging methods.


  • Open Access

    A Study on Refraction Error Compensation Method for Underwater Spinning Laser Scanning 3D Imaging

    by Jinghui Zhang, Yuhang Wang, Tao Zhang, Kai Yang, Jian Zhang, Xinyu Wang

    Laser scanning 3D imaging technology, because it can get accurate three-dimensional surface data, has been widely used in the search for wrecks and rescue operations, underwater resource development, and other fields. At present, the conventional underwater rotating laser scanning imaging system maintains a relatively fixed light window. However, in low-light situations underwater, the rotation of the scanning device causes some degree of water fluctuation, which warps the light strip data that the system sensor receives about the object's surface. To solve the problem, this research studies an underwater 3D scanning and imaging system that makes use of a fixed-light window and a spinning laser (FWLS). A refraction error compensation algorithm is investigated that is based on the fundamentals of linear laser scanning imaging and the dynamic refraction mathematical model is established by the motion of the imaging device. During the imaging process, the incident angle between the laser and the light window varies due to the scanning mode of the system. The experimental results show that the reconstruction radius error is reduced by 60% (from 2.5 mm to about 1 mm) when the measurement data for a standard sphere with a radius of 20 mm are compensated. Moreover, the compensated point cloud data exhibits a higher degree of correspondence with the model of the standard spherical point cloud. This study has a specific reference value for the refractive error analysis of an underwater laser scanning imaging system, and it provides certain research ideas for the subsequent refractive error analysis of various scanning imaging modalities.

  • Open Access

    Cavitation Observation and Noise Characteristics in Rectangular Throttling Groove Spool

    by Jian Zhang, Jifeng Fu, Xinyang Zhang, Tao Zhang, Yuhang Wang

    A hydraulic cavitation platform was developed in order to examine the occurrence of cavitation in the rectangular throttling groove spool and its correlation with noise characteristics. The test valve is constructed using PMMA material, which possesses excellent transparency. This transparency enables direct visual examination of cavitation occurring at the throttle slot. Additionally, high-speed photography is employed to observe the flow characteristics of the valve port, facilitating the analysis of cavitation morphology changes. Furthermore, a noise meter is utilized to measure and record the noise level and its corresponding spectrum. The flow field and flow phenomena at the rectangular throttling groove spool were studied using high-speed photography, noise spectrum analysis, and other methods. It is discovered that back pressure has the greatest influence on cavitation and flow separation, followed by the influence of intake pressure on cavitation morphology and noise. As the back pressure lowers, the cavitation morphology changes from flaky to cloudy, and the cavitation intensity, distribution area, and noise level increase. Background noise and cavitation noise have distinct frequency differences; cavitation noise in the rectangular throttling groove spool is high-frequency noise, with a frequency of more than 8 kHz, and the higher the frequency, the greater the difference in noise value. The magnitude of the alterations in noise intensity is minimal. The noise values exhibit slight variations of 2.3 dB, 4 dB, and 4.3 dB under varying back pressure circumstances of 3 MPa, 4 MPa, and 5 MPa inlet pressure, respectively. It is recommended to use the frequency of cavitation noise to detect the cavitation state and monitor the cavitation process. In the low-frequency region, the cavitation noise in the rectangular throttle groove valve core is not significantly different. Once the center frequency surpasses 3.15 kHz, a discernible distinction emerges, with the magnitude of the discrepancy in noise value increasing as the frequency rises. In other words, the cavitation cloud does not pulsate at one single frequency, but rather in a range of relatively high frequencies (more than 3.15 kHz).


  • Open Access

    Design and Analysis of XY Large Travel Micro Stage Based on Secondary Symmetric Lever Amplification

    by Tao Zhang, Liuguang Xiong, Zequan Pan, Chunhua Zhang, Wen Qu, Yuhang Wang, Chunmei Yang

    This study presents a newly developed piezoelectric drive mechanism for the purpose of designing, analyzing, and testing a micro-positioning platform driven by piezoelectric actuators. The platform incorporates a piezoelectric ceramic actuator and a flexible hinge drive and features a symmetrical two-stage lever (STSL) amplification mechanism and a parallelogram output structure. The implementation of this design has led to notable enhancements in the dynamic properties of the platform, thereby eliminating the undesired parasitic displacement of the mechanism. An analytical model describing the fully elastic deformation of the platform is established, which is further verified by finite element simulation. Finally, the static and dynamic performances of the platform are comprehensively evaluated through experiments. A closed-loop control strategy is adopted to eliminate the nonlinear hysteresis phenomenon of the piezoceramic actuator (PEA). The experimental results show that the piezoelectric micro-actuator platform has a motion range of 97.84 μm × 98.03 μm; the output coupling displacement error is less than 1%; the resolutions of the two axes are 8.1 nm and 8 nm, respectively; and the x-axis and y-axis trajectory tracking errors are both 0.6%. The piezoelectric micromotion platform has good dynamic properties, precision, and stability. The design has a wide application potential in the field of micro-positioning.


  • Open Access

    Advanced Control Systems for Axial Piston Pumps Enhancing Variable Mechanisms and Robust Piston Positioning

    by Yuan Feng, Zhang Jian, Jiayang Li, Zhang Tao, Yuhang Wang, Jingwei Xue

    Axial piston pumps provide a number of benefits, including strong pressure resistance, high efficiency, high transmission power, a broad speed range, and a long lifespan. These characteristics have led to their widespread usage in naval applications, construction machines, and hydraulic machinery. On the other hand, axial piston pumps frequently display reduced operating speeds as well as instability because of their inherently nonlinear properties. In this study, a mathematical model of these changeable (variable) processes is developed using a mix of theoretical calculations and acquired data. An investigation of variable mechanism control in axial piston pumps is carried out centered on robust control methods, and the controller is constructed utilizing robust H∞ theory. In terms of resilience, control precision, and system reaction time, simulations show that the H controller surpasses the PID controller.