Seyed Mohammad Jesmani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Seyed Mohammad Jesmani has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Mostafa Karamouz
Department of Metals, Institute of Science and High Technology and Environmental Sciences, Graduate University of Advanced Technology, Kerman, Iran
6 shared publications - Hamid Mazaheri Tehrani
Department of Mathematics Science, Yazd University, Yazd, Iran
2 shared publications - Ali Alizadeh
Faculty of Materials and Manufacturing Processes, Malek Ashtar University of Technology, Tehran, Iran
1 shared publication Hafez Banasaz
Department of Engineering Sciences, Technical and Vocational University (TVU), Tehran, Iran
1 shared publicationMahdi Aberi
Department of Basic Sciences, Technical and Vocational University (TVU), Tehran, Iran
1 shared publicationMajid Bagheri
Department of Metals, Institute of Science and High Technology and Environmental Sciences, Graduate University of Advanced Technology, Kerman, Iran
1 shared publication
Latest Publications
- 9 January 2026
- Published by Springer Nature in Complex Analysis and Operator Theory
- Vol. 20 (2) , 44
Real and Complex $(p,q)-$extension Chebyshev Polynomials and Complex Best Uniformly Approximation- 9 January 2026
- Published by Springer Nature in Complex Analysis and Operator Theory
- Vol. 20 (2) , 44
Real and Complex $(p,q)-$extension Chebyshev Polynomials and Complex Best Uniformly Approximation- 18 December 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (1)
Microstructural refinement and tensile improvement of as-cast A380 alloy with 0.5 wt.% nano-SiO 2 particles
The effects of adding 0.5 wt.% nano-SiO₂ particles on the evolution of microstructure and tensile behavior of as-cast A380 aluminum alloy were studied. The optical micrographs showed a remarkable reduction of grain size from ~650 μm to ~350 μm (~46%), and SEM images indicated that the coarse β-Fe needles were transformed to compact α-Fe phases, which is due to the nucleating and pinning effects of SiO₂ nanoparticles. The length and aspect ratio of Si also decreased from ~18 μm and 7 to ~4 μm and 3. Tensile testing revealed an increase in strength of around 32% (from 190 MPa to 250 MPa) and a 100% increase in elongation (from 3% to 6%), along with the transition of brittle fracture to ductile fracture. The vortex method led to uniform SiO₂ dispersion, minimizing agglomeration and supporting the potential of A380 alloy for highperformance applications in the automotive and aviation industries
- 18 December 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (1)
Microstructural refinement and tensile improvement of as-cast A380 alloy with 0.5 wt.% nano-SiO 2 particles
The effects of adding 0.5 wt.% nano-SiO₂ particles on the evolution of microstructure and tensile behavior of as-cast A380 aluminum alloy were studied. The optical micrographs showed a remarkable reduction of grain size from ~650 μm to ~350 μm (~46%), and SEM images indicated that the coarse β-Fe needles were transformed to compact α-Fe phases, which is due to the nucleating and pinning effects of SiO₂ nanoparticles. The length and aspect ratio of Si also decreased from ~18 μm and 7 to ~4 μm and 3. Tensile testing revealed an increase in strength of around 32% (from 190 MPa to 250 MPa) and a 100% increase in elongation (from 3% to 6%), along with the transition of brittle fracture to ductile fracture. The vortex method led to uniform SiO₂ dispersion, minimizing agglomeration and supporting the potential of A380 alloy for highperformance applications in the automotive and aviation industries
- Open Access
- 16 December 2025
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Investigation of licorice extract as a green additive on microstructure, hardness, and wear behavior of electrodeposited nickel coatings
In this research, the effect of the utilization of licorice extract as an environmentally friendly additive in the electrodeposition process of nickel coatings on copper substrates was studied. Various concentrations of licorice extract, including 0 wt%, 0.033 wt%,0.066 wt%, and 0.132 wt% were added to a modified Watts bath, and the microstructure, hardness, and wear behavior of the Ni-electrodeposited coating were investigated. The results showed that the addition of licorice extract improved the surface morphology and refined the grain structure of the coating. In addition, a significant improvement in hardness occurred from 136 HV0.3 to 283 HV0.3 with the optimal amount of the additive, which was determined to be 0.066 wt%, owing to better nucleation, structure refinement, and lack of cracks. The wear tests showed enhanced wear resistance and reduced coefficient of friction up to 0.066 wt%. Beyond this, 0.132 wt% of the additive induced internal stress cracks, limiting the balance between hardness and structural integrity. In general, licorice extract can be considered an effective green additive for industrial applications in the Ni electrodeposition process.
- 16 December 2025
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessInvestigation of licorice extract as a green additive on microstructure, hardness, and wear behavior of electrodeposited nickel coatings
In this research, the effect of the utilization of licorice extract as an environmentally friendly additive in the electrodeposition process of nickel coatings on copper substrates was studied. Various concentrations of licorice extract, including 0 wt%, 0.033 wt%,0.066 wt%, and 0.132 wt% were added to a modified Watts bath, and the microstructure, hardness, and wear behavior of the Ni-electrodeposited coating were investigated. The results showed that the addition of licorice extract improved the surface morphology and refined the grain structure of the coating. In addition, a significant improvement in hardness occurred from 136 HV0.3 to 283 HV0.3 with the optimal amount of the additive, which was determined to be 0.066 wt%, owing to better nucleation, structure refinement, and lack of cracks. The wear tests showed enhanced wear resistance and reduced coefficient of friction up to 0.066 wt%. Beyond this, 0.132 wt% of the additive induced internal stress cracks, limiting the balance between hardness and structural integrity. In general, licorice extract can be considered an effective green additive for industrial applications in the Ni electrodeposition process.
- 9 September 2024
- Published by Springer Nature in JOM
- Vol. 76 (12) , 7002-7010
Hybrid Modification of Microstructure and Tensile Properties of A319 Alloy by Heat Treatment and Be Addition
- 9 September 2024
- Published by Springer Nature in JOM
- Vol. 76 (12) , 7002-7010
Hybrid Modification of Microstructure and Tensile Properties of A319 Alloy by Heat Treatment and Be Addition
- 3 September 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 11020-11028
Influence of Be Content and T4 Temper Heat Treatment on Hardness and Wear Behavior of Al-Alloy A319
- 3 September 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 11020-11028
Influence of Be Content and T4 Temper Heat Treatment on Hardness and Wear Behavior of Al-Alloy A319
- 27 June 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (9) , 7955-7964
Modification of Microstructure, Hardness, and Wear Behavior of Al-8.5Si-2.3Cu Alloy by Various Melt Shearing Speeds
- 27 June 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (9) , 7955-7964
Modification of Microstructure, Hardness, and Wear Behavior of Al-8.5Si-2.3Cu Alloy by Various Melt Shearing Speeds
- 26 April 2024
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 77 (9) , 2393-2402
Influence of Various Melt Shearing Speeds on Macrostructure, Microstructure, and Tensile Properties of A380 Aluminum Alloy
- 26 April 2024
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 77 (9) , 2393-2402
Influence of Various Melt Shearing Speeds on Macrostructure, Microstructure, and Tensile Properties of A380 Aluminum Alloy
- 5 April 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (5) , 4328-4335
Evaluation of Tensile Properties and Formability of Al 6061 Alloy Processed by Various Semi-solid Techniques
- 5 April 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (5) , 4328-4335
Evaluation of Tensile Properties and Formability of Al 6061 Alloy Processed by Various Semi-solid Techniques
- 26 August 2023
- Published by Springer Nature in Iranian Journal of Science
- Vol. 47 (5-6) , 1613-1616
Qproximinal and Qremotal in normed spaces
- 26 August 2023
- Published by Springer Nature in Iranian Journal of Science
- Vol. 47 (5-6) , 1613-1616
Qproximinal and Qremotal in normed spaces