Jaywant H. Arakeri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jaywant H. Arakeri has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Navneet Kumar
IIT Jammu
5 shared publications - Dipendra Gupta
Cornell University
4 shared publications - Sanjay. P. Sane
National Centre for Biological Sciences
3 shared publications - Suyog V. Mahulkar
Indian Institute of Science Banglore India
3 shared publications - Alok Kumar
Department of Mechanical Engineering, Indian Institute of Technology Bombay , Powai, Mumbai 400076, India
2 shared publications - Atul Srivastava
Indian Institute of Technology Bombay
2 shared publications
Latest Publications
- Open Access
- 1 June 2026
- Published by Elsevier in SSRN Electronic Journal
Vapor evolution and condensation dynamics in a differentially-heated immiscible DCM-Water layer system: High speed videography and IR measurements
The present study is concerned with the experimental investigation of boiling and condensation characteristics of one of the high volatile fluids as it undergoes phase change in a differentially-heated two-fluids system. The vertically stratified immiscible-fluids system is realized with dichloromethane (DCM), the more volatile component, as the (heavier) bottom fluid and water as the top fluid layer. Phase change in the bottom DCM layer is affected through localized heating using a transparent ITO-coated borofloat glass substrate, triggering nucleate boiling. The resulting vapor bubbles rise through the overlying water layer and condense on a horizontally placed top plate. Synchronized high-speed videography and infrared thermography are employed to resolve key interfacial processes including nucleation, interface deformation, neck formation, pinch-off of entrapped vapor volume, and its condensation at the top plate. An energy balance framework is developed to quantify local heat storage, lateral conduction, natural convection, radiation at the top plate. The analysis shows that lateral conduction within the copper plate constitutes the dominant heat dissipation pathway during condensation. Spatio-temporal variations in surface heat flux around the impact region highlight the influence of localized phase-change events on transient thermal transport. Comparison of the total estimated dissipated energy with the theoretical latent energy corresponding to a pure vapor bubble reveals that the entrapped volume carries a lower effective vapor content. It is thus inferred that the entrapped vapor bubble therefore consists of a composite liquid–vapor mixture, with the liquid fraction estimated to be approximately 45–58% across the tested heat flux range. The presence of this encapsulated liquid layer explains the stability of the rising entrapped volume, which undergoes almost negligible condensation while traversing through the water layer. The insights obtained enhance the understanding of vapor transport and condensation mechanisms in immiscible fluid systems and offer guidance for the development of passive, high-performance thermal management schemes.
- 1 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessVapor evolution and condensation dynamics in a differentially-heated immiscible DCM-Water layer system: High speed videography and IR measurements
The present study is concerned with the experimental investigation of boiling and condensation characteristics of one of the high volatile fluids as it undergoes phase change in a differentially-heated two-fluids system. The vertically stratified immiscible-fluids system is realized with dichloromethane (DCM), the more volatile component, as the (heavier) bottom fluid and water as the top fluid layer. Phase change in the bottom DCM layer is affected through localized heating using a transparent ITO-coated borofloat glass substrate, triggering nucleate boiling. The resulting vapor bubbles rise through the overlying water layer and condense on a horizontally placed top plate. Synchronized high-speed videography and infrared thermography are employed to resolve key interfacial processes including nucleation, interface deformation, neck formation, pinch-off of entrapped vapor volume, and its condensation at the top plate. An energy balance framework is developed to quantify local heat storage, lateral conduction, natural convection, radiation at the top plate. The analysis shows that lateral conduction within the copper plate constitutes the dominant heat dissipation pathway during condensation. Spatio-temporal variations in surface heat flux around the impact region highlight the influence of localized phase-change events on transient thermal transport. Comparison of the total estimated dissipated energy with the theoretical latent energy corresponding to a pure vapor bubble reveals that the entrapped volume carries a lower effective vapor content. It is thus inferred that the entrapped vapor bubble therefore consists of a composite liquid–vapor mixture, with the liquid fraction estimated to be approximately 45–58% across the tested heat flux range. The presence of this encapsulated liquid layer explains the stability of the rising entrapped volume, which undergoes almost negligible condensation while traversing through the water layer. The insights obtained enhance the understanding of vapor transport and condensation mechanisms in immiscible fluid systems and offer guidance for the development of passive, high-performance thermal management schemes.
- 30 September 2025
- Published by Springer Nature in Sādhanā
- Vol. 50 (4) , 1-31
Some insights into evaporation under natural convection from surfaces: soils to leaves
- 30 September 2025
- Published by Springer Nature in Sādhanā
- Vol. 50 (4) , 1-31
Some insights into evaporation under natural convection from surfaces: soils to leaves
- Open Access
- 6 August 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1016
Convection in slender Rayleigh–Bénard cells is a combination of wall and tube components
A model for obtaining scaling laws for Rayleigh–Bénard convection (RBC) at high Rayleigh numbers in tall, slender cells (cells with low aspect ratio, $\varGamma = d/H \ll 1$ ) is presented. Traditional RBC ( $\varGamma \gtrsim 1$ ) is characterised by large-eddy circulation scaling with the height of the cell, a near-isothermal core and almost all the thermal resistance provided at the horizontal walls. In slender RBC cells, on the other hand, away from the horizontal walls, tube-like convection with eddies scaling with the tube diameter and a linear temperature gradient driving the convective flow is present. The crux of our approach is to split the cell into two components: (i) ‘wall convection’ near the top and bottom horizontal walls and (ii) ‘tube convection (TC)’ in the central part away from the walls. By applying the scaling relations for both wall convection and TC, and treating the total thermal resistance as a sum of their contributions, unified scaling relations for Nusselt number, Reynolds number and mean vertical temperature gradient in slender RBC cells are developed. Our model is applicable for high enough Rayleigh numbers, such that convection both at the wall and in the tube are turbulent. Our model predictions compare well with the data from various studies in slender RBC cells where these conditions are satisfied. In particular, the effects of $\varGamma$ and Prandtl number are well captured. We propose a scaled aspect ratio using which we obtain ‘universal’ correlations for the heat flux and for the fractional temperature drop in the tube that include the effects of Rayleigh and Prandtl numbers. The profiles of suitably scaled horizontal and vertical velocity fluctuations, along with estimates for boundary layer thickness near the horizontal walls, and the radial distribution of the velocity fluctuations in the tube part are also presented.- 6 August 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1016
Open AccessConvection in slender Rayleigh–Bénard cells is a combination of wall and tube components
A model for obtaining scaling laws for Rayleigh–Bénard convection (RBC) at high Rayleigh numbers in tall, slender cells (cells with low aspect ratio, $\varGamma = d/H \ll 1$ ) is presented. Traditional RBC ( $\varGamma \gtrsim 1$ ) is characterised by large-eddy circulation scaling with the height of the cell, a near-isothermal core and almost all the thermal resistance provided at the horizontal walls. In slender RBC cells, on the other hand, away from the horizontal walls, tube-like convection with eddies scaling with the tube diameter and a linear temperature gradient driving the convective flow is present. The crux of our approach is to split the cell into two components: (i) ‘wall convection’ near the top and bottom horizontal walls and (ii) ‘tube convection (TC)’ in the central part away from the walls. By applying the scaling relations for both wall convection and TC, and treating the total thermal resistance as a sum of their contributions, unified scaling relations for Nusselt number, Reynolds number and mean vertical temperature gradient in slender RBC cells are developed. Our model is applicable for high enough Rayleigh numbers, such that convection both at the wall and in the tube are turbulent. Our model predictions compare well with the data from various studies in slender RBC cells where these conditions are satisfied. In particular, the effects of $\varGamma$ and Prandtl number are well captured. We propose a scaled aspect ratio using which we obtain ‘universal’ correlations for the heat flux and for the fractional temperature drop in the tube that include the effects of Rayleigh and Prandtl numbers. The profiles of suitably scaled horizontal and vertical velocity fluctuations, along with estimates for boundary layer thickness near the horizontal walls, and the radial distribution of the velocity fluctuations in the tube part are also presented. - 27 November 2024
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 9 (11)
Contrasting flow dynamics between stationary and moving clapping bodies
- 27 November 2024
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 9 (11)
Contrasting flow dynamics between stationary and moving clapping bodies
- 1 August 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (8)
A dimensionless heat transfer coefficient for free convection that is more appropriate than Nusselt number
Heat transfer in flows created by buoyancy, or natural convection, is a widely studied topic across various disciplines spanning natural flows as well as those with engineering applications. The convective heat transfer rate on a surface is commonly represented by the Nusselt number (Nu), a ratio of convective to diffusive transport, expressed often as RanPrm, where Ra is the Rayleigh number, the buoyancy forcing parameter, and Pr the Prandtl number. Motivated by the observation that n∼1/3 for turbulent convection, which implies the heat flux is independent of the length scale (L, characteristic length related to the geometry), we propose an alternate and physically more meaningful non-dimensional heat transfer parameter, denoted by Cq. Cq is derived using only the near wall variables and does not contain L. For n=1/3, Cq is constant. Even for laminar convection, where n∼1/4, Cq∼Ra−1/12, a weak function of Ra. We show that for natural convection over several geometries and a wide range of Ra, the Cq values within a narrow range while the corresponding Nu values span several orders of magnitude. We also show that Cq is akin to the non-dimensional representation of wall shear stress, skin friction coefficient Cf. We believe that just like Cf, Cq will be an equally useful non-dimensional measure of heat transfer in natural convection flows.
- 1 August 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (8)
A dimensionless heat transfer coefficient for free convection that is more appropriate than Nusselt number
Heat transfer in flows created by buoyancy, or natural convection, is a widely studied topic across various disciplines spanning natural flows as well as those with engineering applications. The convective heat transfer rate on a surface is commonly represented by the Nusselt number (Nu), a ratio of convective to diffusive transport, expressed often as RanPrm, where Ra is the Rayleigh number, the buoyancy forcing parameter, and Pr the Prandtl number. Motivated by the observation that n∼1/3 for turbulent convection, which implies the heat flux is independent of the length scale (L, characteristic length related to the geometry), we propose an alternate and physically more meaningful non-dimensional heat transfer parameter, denoted by Cq. Cq is derived using only the near wall variables and does not contain L. For n=1/3, Cq is constant. Even for laminar convection, where n∼1/4, Cq∼Ra−1/12, a weak function of Ra. We show that for natural convection over several geometries and a wide range of Ra, the Cq values within a narrow range while the corresponding Nu values span several orders of magnitude. We also show that Cq is akin to the non-dimensional representation of wall shear stress, skin friction coefficient Cf. We believe that just like Cf, Cq will be an equally useful non-dimensional measure of heat transfer in natural convection flows.
- Open Access
- 8 July 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (7) , e0305084
Generating controlled gust perturbations using vortex rings
To understand the locomotory mechanisms of flying and swimming animals, it is often necessary to develop assays that enable us to measure their responses to external gust perturbations. Typically, such measurements have been carried out using a variety of gusts which are difficult to control or characterize owing to their inherently turbulent nature. Here, we present a method of generating discrete gusts under controlled laboratory conditions in the form of a vortex rings which are well-characterized and highly controllable. We also provide the theoretical guidelines underlying the design of gust generators for specific applications. As a case study, we tested the efficacy of this method to study the flight response of freely-flying soldier flies Hermetia illucens. The vortex ring based method can be used to generate controlled gusts to study diverse phenomena ranging from a natural flight in insects to the artificial flight of insect-sized drones and micro-aerial vehicles.
- 8 July 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (7) , e0305084
Open AccessGenerating controlled gust perturbations using vortex rings
To understand the locomotory mechanisms of flying and swimming animals, it is often necessary to develop assays that enable us to measure their responses to external gust perturbations. Typically, such measurements have been carried out using a variety of gusts which are difficult to control or characterize owing to their inherently turbulent nature. Here, we present a method of generating discrete gusts under controlled laboratory conditions in the form of a vortex rings which are well-characterized and highly controllable. We also provide the theoretical guidelines underlying the design of gust generators for specific applications. As a case study, we tested the efficacy of this method to study the flight response of freely-flying soldier flies Hermetia illucens. The vortex ring based method can be used to generate controlled gusts to study diverse phenomena ranging from a natural flight in insects to the artificial flight of insect-sized drones and micro-aerial vehicles.
- Open Access
- 19 September 2023
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 971, A25
A self-propelling clapping body
We report an experimental study of the motion of a clapping body consisting of two flat plates pivoted at the leading edge by a torsion spring. Clapping motion and forward propulsion of the body are initiated by the sudden release of the plates, initially held apart at an angle .
- 19 September 2023
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 971, A25
Open AccessA self-propelling clapping body
We report an experimental study of the motion of a clapping body consisting of two flat plates pivoted at the leading edge by a torsion spring. Clapping motion and forward propulsion of the body are initiated by the sudden release of the plates, initially held apart at an angle .
- Open Access
Endothelial mechanobiology under controlled disturbed flows
Early atherosclerotic lesions often develop in areas of disturbed flow within arterial curvatures and bifurcations. Complex flows alter the signaling of inflammatory and other signaling molecules that may exacerbate the disease phenotype. Microfluidic platforms to assess changes in endothelial mechanobiology generally employ laminar unidirectional or oscillatory flows generated in straight channels; such platforms do not however mimic the complex time-varying bi-directional shear patterns on arterial walls. We fabricated an endothelium-on-chip device to generate “controlled” disturbed flows, characterized using a wall shear rosette, such as those reported in aneurysmal vessels and in regions with atherosclerotic plaques. We cultured human aortic endothelial cells (HAEC) in the device and subjected the monolayer to a circular shear rosette which represents bidirectional and oscillatory shear stresses. Immunofluorescence results show large cuboidal cells with significantly higher nuclear areas, changes in the localization of VE-Cadherin, elevated actin and NF-kB expressions in the device as compared to cell monolayers subjected to laminar flow, unidirectional oscillatory flow, and No-flow conditions. The creation of a dysfunctional endothelial monolayer due to bidirectional oscillatory flows also correlated with dramatic changes to the lamin A/C distribution and heterochromatin organization in the nucleus that have not been reported earlier. Such studies are potentially useful to assess novel therapeutics, mitigate effects of vascular disease for personalized medicine, study thrombus creation in the vicinity of inflamed endothelial monolayers, and reduce ourreliance on animal trials. Our device and analytical method represent the first successful demonstration of generating controlled disturbed flows in microfluidic devices
Open AccessEndothelial mechanobiology under controlled disturbed flows
Early atherosclerotic lesions often develop in areas of disturbed flow within arterial curvatures and bifurcations. Complex flows alter the signaling of inflammatory and other signaling molecules that may exacerbate the disease phenotype. Microfluidic platforms to assess changes in endothelial mechanobiology generally employ laminar unidirectional or oscillatory flows generated in straight channels; such platforms do not however mimic the complex time-varying bi-directional shear patterns on arterial walls. We fabricated an endothelium-on-chip device to generate “controlled” disturbed flows, characterized using a wall shear rosette, such as those reported in aneurysmal vessels and in regions with atherosclerotic plaques. We cultured human aortic endothelial cells (HAEC) in the device and subjected the monolayer to a circular shear rosette which represents bidirectional and oscillatory shear stresses. Immunofluorescence results show large cuboidal cells with significantly higher nuclear areas, changes in the localization of VE-Cadherin, elevated actin and NF-kB expressions in the device as compared to cell monolayers subjected to laminar flow, unidirectional oscillatory flow, and No-flow conditions. The creation of a dysfunctional endothelial monolayer due to bidirectional oscillatory flows also correlated with dramatic changes to the lamin A/C distribution and heterochromatin organization in the nucleus that have not been reported earlier. Such studies are potentially useful to assess novel therapeutics, mitigate effects of vascular disease for personalized medicine, study thrombus creation in the vicinity of inflamed endothelial monolayers, and reduce ourreliance on animal trials. Our device and analytical method represent the first successful demonstration of generating controlled disturbed flows in microfluidic devices
- Open Access
- 14 April 2023
- Published by Springer Nature
- p. 68
Preferential Air Invasion in an Evaporating Monolayer Porous Medium
- 14 April 2023
- Published by Springer Nature
- p. 68
Open AccessPreferential Air Invasion in an Evaporating Monolayer Porous Medium