Miloš M. Jovanović
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Miloš M. Jovanović has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Saša M. Milanović
Faculty of Mechanical Engineering, University of Niš, Niš, Serbia
3 shared publications - Zivan Spasic
Faculty of Mechanical Engineering, University of Niš, Niš, Serbia
3 shared publications - Aleksandar Boricic
Faculty of Mechanical Engineering, University of Niš, Niš, Serbia
2 shared publications B.T. Irving
Delta Products Corporation|Research Triangle Park
1 shared publication- Boban Nikolić
Faculty of Mechanical Engineering, University of Niš, A. Medvedeva 14, 18000 Niš, Serbia
1 shared publication F.C. Lee
Bradley Dept. of Electr. Eng., Virginia Polytech. Inst. & State Univ., Blacksburg, VA, USA
1 shared publication
Latest Publications
- Open Access
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Flow, heat,p. 356-364
A model of two-phase flow in pneumatic transport of powder material
The paper presents a numerical simulation of two-phase turbulent flow in straight horizontal channels with a square cross-section, with the dimensions of 200x200 mm and the length of 80Dh. The flow of solid particles of quartz, flour and ash using air was chosen for the two-phase flow simulation. During the modelling of the flow, the transported particles were observed as spherical. The turbulence was modelled using a full Reynolds stress model, while the complete model was used to examine turbulent stresses and turbulent temperature fluxes. The same initial flow conditions and a single uniform grid were employed in all numerical experiments. The fineness of the numerical grid was tested during the simulation, and the paper shows the results of the numerical grid of the highest resolution beyond which the fineness did not affect the obtained results. The paper also presents the change in the velocity of the transported material by air in the cross-section and along the channel.
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Flow, heat,p. 356-364
Open AccessA model of two-phase flow in pneumatic transport of powder material
The paper presents a numerical simulation of two-phase turbulent flow in straight horizontal channels with a square cross-section, with the dimensions of 200x200 mm and the length of 80Dh. The flow of solid particles of quartz, flour and ash using air was chosen for the two-phase flow simulation. During the modelling of the flow, the transported particles were observed as spherical. The turbulence was modelled using a full Reynolds stress model, while the complete model was used to examine turbulent stresses and turbulent temperature fluxes. The same initial flow conditions and a single uniform grid were employed in all numerical experiments. The fineness of the numerical grid was tested during the simulation, and the paper shows the results of the numerical grid of the highest resolution beyond which the fineness did not affect the obtained results. The paper also presents the change in the velocity of the transported material by air in the cross-section and along the channel.
- Open Access
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (6 Part A) , 4401-4416
Thermal drift in an inclined viscous fluid flow
This paper considers viscous fluid flow in a slot between two parallel plates which start inclining with respect to the horizontal line. The lower plate was heated and had non-homogeneous temperature distribution while the upper plate was cooled and with homogeneous temperature distribution. The spatially periodic temperature distribution was gradually applied at the lower plate, after which the plates were slowly inclined in the positive-counterclockwise direction, and the fields of vorticity, stream function, and temperature are presented for different values of the angle of inclination. We used the vorticity-stream function formulation of Navier-Stokes equations, Fourier-Galerkin, and Chebyshev collocation method for numerical simulation of 2-D viscous fluid flow. We carried out numerical simulation using our in-house MATLAB code for subcritical uniform Rayleigh number, Rauni, and periodic Rayleigh number, Rap, on the lower plate. An accurate numerical scheme was developed to capture the full time-dependent behavior here. The interest lied in how the intensities of the vortexes and convection rolls changed as the inclination angle was increased with respect to time. Convection rolls rotating in the clockwise direction expanded and the rolls rotating in the counterclockwise direction shrank and their centers moved closer to the lower wall. Thermal drift appeared between them when the inclination angle started increasing.
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (6 Part A) , 4401-4416
Open AccessThermal drift in an inclined viscous fluid flow
This paper considers viscous fluid flow in a slot between two parallel plates which start inclining with respect to the horizontal line. The lower plate was heated and had non-homogeneous temperature distribution while the upper plate was cooled and with homogeneous temperature distribution. The spatially periodic temperature distribution was gradually applied at the lower plate, after which the plates were slowly inclined in the positive-counterclockwise direction, and the fields of vorticity, stream function, and temperature are presented for different values of the angle of inclination. We used the vorticity-stream function formulation of Navier-Stokes equations, Fourier-Galerkin, and Chebyshev collocation method for numerical simulation of 2-D viscous fluid flow. We carried out numerical simulation using our in-house MATLAB code for subcritical uniform Rayleigh number, Rauni, and periodic Rayleigh number, Rap, on the lower plate. An accurate numerical scheme was developed to capture the full time-dependent behavior here. The interest lied in how the intensities of the vortexes and convection rolls changed as the inclination angle was increased with respect to time. Convection rolls rotating in the clockwise direction expanded and the rolls rotating in the counterclockwise direction shrank and their centers moved closer to the lower wall. Thermal drift appeared between them when the inclination angle started increasing.
- Open Access
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (6 Part A) , 4417-4429
New method for calculating heat transfer in unsteady MHD mixed boundary-layers with radiative and generation heat over a cylinder
This paper is devoted to the analysis of an unsteady 2-D MHD dynamic and thermal boundary-layer over a horizontal cylinder in mixed convection, in the presence of suction/injection, heat source/sink, and heat radiation fluid electrical conductivity is constant. The system of MHD equations of dynamic and temperature boundary-layer, which describe complex non-auto model problems, has been solved by a new approach. New variables and sets of parameters were introduced and transformed equations were obtained, in which the influence of the magnitude Z was explicitly retained. In order to close the system of equations, to the equations of the boundary-layers momentum equation was added. The solution of the obtained system of non-linear differential equations was performed numerically using the finite difference method, with the simultaneous application of the iteration method. By replacing the derivatives in the system of equations with the corresponding relations of finite differences, a system of linear derivative algebraic equations is obtained, which is solved by the three-diagonal method. As a concrete example of the introduced method, the effects of heat transfer in the MHD boundary-layers were considered, in the case of mixed convention, over a horizontal circular cylinder. The boundary conditions for temperature are defined by linear functions of longitudinal co-ordinates and time. Numerical results for different Eckart, Schmidt, and expanded Prandtl numbers and values: magnetic, dynamic, thermal parameters, temperature, and buoyancy parameters were obtained and presented. The obtained results were analyzed through the diagrams of changes in velocity and temperature and the diagrams of integral and differential characteristics of boundary-layers and the corresponding conclusions were given.
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (6 Part A) , 4417-4429
Open AccessNew method for calculating heat transfer in unsteady MHD mixed boundary-layers with radiative and generation heat over a cylinder
This paper is devoted to the analysis of an unsteady 2-D MHD dynamic and thermal boundary-layer over a horizontal cylinder in mixed convection, in the presence of suction/injection, heat source/sink, and heat radiation fluid electrical conductivity is constant. The system of MHD equations of dynamic and temperature boundary-layer, which describe complex non-auto model problems, has been solved by a new approach. New variables and sets of parameters were introduced and transformed equations were obtained, in which the influence of the magnitude Z was explicitly retained. In order to close the system of equations, to the equations of the boundary-layers momentum equation was added. The solution of the obtained system of non-linear differential equations was performed numerically using the finite difference method, with the simultaneous application of the iteration method. By replacing the derivatives in the system of equations with the corresponding relations of finite differences, a system of linear derivative algebraic equations is obtained, which is solved by the three-diagonal method. As a concrete example of the introduced method, the effects of heat transfer in the MHD boundary-layers were considered, in the case of mixed convention, over a horizontal circular cylinder. The boundary conditions for temperature are defined by linear functions of longitudinal co-ordinates and time. Numerical results for different Eckart, Schmidt, and expanded Prandtl numbers and values: magnetic, dynamic, thermal parameters, temperature, and buoyancy parameters were obtained and presented. The obtained results were analyzed through the diagrams of changes in velocity and temperature and the diagrams of integral and differential characteristics of boundary-layers and the corresponding conclusions were given.
- Open Access
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (6 Part B) , 5053-5062
Aerodynamic performance of the reversible axial fan for high air temperatures
The paper presents the aerodynamic performance of an axial reversible fan for high air temperatures, obtained by applying the similarity theory and numerical flow simulations. This analysis was performed for the possibility of installing the existing structure of an impeller of a reversible fan in a jet fan for the longitudinal ventilation of a tunnel. The direction of forced flow in tunnels changes, and it is always towards low atmospheric pressure, i.e. in the direction of natural air-flow. These fans often work with high air temperatures in the event of a fire. The paper shows the performance of fans for high operating air temperatures, up to 400?C. The results were obtained through numerical simulations of the flow in an original design fan, whose performance was experimentally determined for normal atmospheric operating conditions (? = 1.2 kg/m3). Performances are given for two fan speeds. Unnecessary corrections of the existing impeller design for use in jet fans for tunnel ventilation were also considered.
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (6 Part B) , 5053-5062
Open AccessAerodynamic performance of the reversible axial fan for high air temperatures
The paper presents the aerodynamic performance of an axial reversible fan for high air temperatures, obtained by applying the similarity theory and numerical flow simulations. This analysis was performed for the possibility of installing the existing structure of an impeller of a reversible fan in a jet fan for the longitudinal ventilation of a tunnel. The direction of forced flow in tunnels changes, and it is always towards low atmospheric pressure, i.e. in the direction of natural air-flow. These fans often work with high air temperatures in the event of a fire. The paper shows the performance of fans for high operating air temperatures, up to 400?C. The results were obtained through numerical simulations of the flow in an original design fan, whose performance was experimentally determined for normal atmospheric operating conditions (? = 1.2 kg/m3). Performances are given for two fan speeds. Unnecessary corrections of the existing impeller design for use in jet fans for tunnel ventilation were also considered.
- 25 June 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 503-508
Analysis, design, and performance evaluation of flying-capacitor passive lossless snubber applied to PFC boost converter
A boost converter which employs a flying-capacitor passive lossless snubber to reduce the losses caused by the reverse-recovery characteristic of the boost rectifier is described. The passive snubber consists of a snubber inductor, two snubber rectifiers, and a snubber capacitor. The losses are reduced by inserting a snubber inductor in the series path of the boost switch and the rectifier to control the di/dt rate of the rectifier during it's turn-off. The snubber is analyzed and design guidelines are offered to achieve optimum performance. The proposed snubber is applied to a 500-W power factor corrected (PFC) boost converter which is designed to operate in the universal line range (90-264 VRMS). Performance evaluations of the proposed snubber are made and compared to the conventional boost converter with respect to efficiency and device temperature.
- 25 June 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 503-508
Analysis, design, and performance evaluation of flying-capacitor passive lossless snubber applied to PFC boost converter
A boost converter which employs a flying-capacitor passive lossless snubber to reduce the losses caused by the reverse-recovery characteristic of the boost rectifier is described. The passive snubber consists of a snubber inductor, two snubber rectifiers, and a snubber capacitor. The losses are reduced by inserting a snubber inductor in the series path of the boost switch and the rectifier to control the di/dt rate of the rectifier during it's turn-off. The snubber is analyzed and design guidelines are offered to achieve optimum performance. The proposed snubber is applied to a 500-W power factor corrected (PFC) boost converter which is designed to operate in the universal line range (90-264 VRMS). Performance evaluations of the proposed snubber are made and compared to the conventional boost converter with respect to efficiency and device temperature.
- 2 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 203-210
Comparison of single-ended-parallel MRC and forward MRC
- 2 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 203-210
Comparison of single-ended-parallel MRC and forward MRC
- 22 November 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 605-611
Forward converter with current-doubler rectifier: analysis, design, and evaluation results
- 22 November 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 605-611
Forward converter with current-doubler rectifier: analysis, design, and evaluation results
- Open Access
- 1 January 1999
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 619-625 vol.1
A novel active snubber for high-power boost converters
A technique which improves the performance of the boost converter by reducing the reverse-recovery-related losses in the boost switch and rectifier with an active snubber that is implemented with a minimum number of components is presented. This minimum-component count snubber consists of a snubber inductor, an auxiliary switch, and a rectifier. The proposed technique reduces the reverse-recovery-related losses by controlling the turn-off di/dt rate of the rectifier current with the snubber inductor connected in series with the boost switch and rectifier. The voltage and current stresses of the components in the proposed active-snubber boost converter are similar to those in its conventional "hard-switched" counterpart.
- 1 January 1999
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 619-625 vol.1
Open AccessA novel active snubber for high-power boost converters
A technique which improves the performance of the boost converter by reducing the reverse-recovery-related losses in the boost switch and rectifier with an active snubber that is implemented with a minimum number of components is presented. This minimum-component count snubber consists of a snubber inductor, an auxiliary switch, and a rectifier. The proposed technique reduces the reverse-recovery-related losses by controlling the turn-off di/dt rate of the rectifier current with the snubber inductor connected in series with the boost switch and rectifier. The voltage and current stresses of the components in the proposed active-snubber boost converter are similar to those in its conventional "hard-switched" counterpart.