Melissa Kozul
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Melissa Kozul has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Richard D. Sandberg
Department of Mechanical Engineering, University of Melbourne, Parkville, VIC 3010, Australia
6 shared publications - Massimiliano Nardini
University of Melbourne Department of Mechanical Engineering
5 shared publications - Ananth Sivaramakrishnan Malathi
Indian Institute of Technology Madras Department of Aerospace Engineering Chennai 600036 , India
2 shared publications - Nagabhushana Rao Vadlamani
Indian Institute of Technology Madras
2 shared publications - Thomas O. Jelly
University of Melbourne Department of Mechanical Engineering Melbourne, VIC 3010
2 shared publications - Aamir Shabbir
GE Aerospace
1 shared publication
Latest Publications
- Open Access
- 30 January 2025
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (8) , 1-13
Optimal Riblets Applied to Gas Turbine Compressor Blades Studied via Direct Numerical Simulation (GT2024–122305)
Streamwise micro-groove surfaces (“riblets”) are well known as a passive surface treatment to reduce drag, which may assist in increasing overall gas turbine efficiency. The first direct numerical simulation of micro-scaled riblets on an axial high-pressure compressor blade at engine-relevant conditions (Kozul et al., 2023, “Direct Numerical Simulation of Riblets Applied to Gas Turbine Compressor Blades at On- and Off-Design Incidences.” Proceedings of the ASME Turbo Expo, Boston, GT2023–10103) demonstrated the ability of riblets to reduce the skin friction along most of the chord of a high-pressure compressor blade, at both on- and off-design inflow incidences. However, this previous study only considered riblets with fixed physical dimensions. The present work considers a “locally optimal” riblet geometry applied to the high-pressure compressor blade, where the riblet geometry is smoothly adjusted along the chord to target optimal riblet dimensions in viscous units, known from fundamental fluid mechanics studies. The present locally optimal riblets do indeed reduce the skin friction on the surface of the high-pressure compressor blade at both design and off-design inflow incidences and are generally at least as effective as the previous fixed-geometry riblets. Yet, the present riblet surfaces tend to increase pressure wake losses. In particular, at positive incidence, although the locally optimal riblets generally further reduce the skin friction compared to the fixed riblets, the wake loss increases by a significant 20% with respect to the reference smooth-blade case. A complex flow interaction with the suction-side separation bubble at the leading edge may be responsible for the significantly increased loss at positive inflow incidence.
- 30 January 2025
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (8) , 1-13
Open AccessOptimal Riblets Applied to Gas Turbine Compressor Blades Studied via Direct Numerical Simulation (GT2024–122305)
Streamwise micro-groove surfaces (“riblets”) are well known as a passive surface treatment to reduce drag, which may assist in increasing overall gas turbine efficiency. The first direct numerical simulation of micro-scaled riblets on an axial high-pressure compressor blade at engine-relevant conditions (Kozul et al., 2023, “Direct Numerical Simulation of Riblets Applied to Gas Turbine Compressor Blades at On- and Off-Design Incidences.” Proceedings of the ASME Turbo Expo, Boston, GT2023–10103) demonstrated the ability of riblets to reduce the skin friction along most of the chord of a high-pressure compressor blade, at both on- and off-design inflow incidences. However, this previous study only considered riblets with fixed physical dimensions. The present work considers a “locally optimal” riblet geometry applied to the high-pressure compressor blade, where the riblet geometry is smoothly adjusted along the chord to target optimal riblet dimensions in viscous units, known from fundamental fluid mechanics studies. The present locally optimal riblets do indeed reduce the skin friction on the surface of the high-pressure compressor blade at both design and off-design inflow incidences and are generally at least as effective as the previous fixed-geometry riblets. Yet, the present riblet surfaces tend to increase pressure wake losses. In particular, at positive incidence, although the locally optimal riblets generally further reduce the skin friction compared to the fixed riblets, the wake loss increases by a significant 20% with respect to the reference smooth-blade case. A complex flow interaction with the suction-side separation bubble at the leading edge may be responsible for the significantly increased loss at positive inflow incidence.
- Open Access
- 20 December 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (4) , 1-13
Unsteady Loss Mechanisms in Low-Pressure Turbines With Diverging End-Walls Studied Via High-Fidelity Simulation
High-fidelity simulations are used to conduct controlled numerical experiments to investigate the effect of periodically incoming wakes on profile and three-dimensional loss mechanisms. The present work considers the MTU-T161 cascade with spanwise diverging end-walls, representative of a high-lift, low-pressure turbine blade. All simulations are carried out at engine-relevant conditions, with exit Reynolds number of 90,000 and exit Mach number of 0.6. Upstream moving bars are used to generate incoming wakes which impinge on the blade and potentially alter its aerodynamic performance. Unlike previous studies, the incoming wakes are subjected to an additional axial pressure gradient when convecting through the passage, due to the divergence of the spanwise end-walls. The evolving secondary vortex systems around the bars periodically disturb the freestream end-wall boundary layer facing the blade leading edge. This ultimately influences the end-wall related losses downstream of the blade and governs the overall aerodynamic performance of the blade. Following validation against available experimental data, a systematic variation of flow coefficient and reduced frequency extends the parametric space studied to encompass engine-realistic operating conditions. The high-fidelity simulations reveal the impact of incoming wakes on blade boundary layer losses and wake-induced losses both at the mid-span and within the end-wall regions. Furthermore, by decomposing the total loss generation, the data-rich results shed light on the underlying physical mechanisms driving unsteady losses when applied to phase- and time-averaged flow fields. Secondary losses incurred in the end-wall region show little sensitivity toward unsteadiness associated with incoming wakes and are rather prone to the turbulence levels in the passage. On the other hand, profile losses show high dependency on bar wakes in the absence of wake fogging. While profile losses can be minimized by certain combinations of flow coefficients and reduced frequencies, they remain the dominant source of unsteady loss generation.
- 20 December 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (4) , 1-13
Open AccessUnsteady Loss Mechanisms in Low-Pressure Turbines With Diverging End-Walls Studied Via High-Fidelity Simulation
High-fidelity simulations are used to conduct controlled numerical experiments to investigate the effect of periodically incoming wakes on profile and three-dimensional loss mechanisms. The present work considers the MTU-T161 cascade with spanwise diverging end-walls, representative of a high-lift, low-pressure turbine blade. All simulations are carried out at engine-relevant conditions, with exit Reynolds number of 90,000 and exit Mach number of 0.6. Upstream moving bars are used to generate incoming wakes which impinge on the blade and potentially alter its aerodynamic performance. Unlike previous studies, the incoming wakes are subjected to an additional axial pressure gradient when convecting through the passage, due to the divergence of the spanwise end-walls. The evolving secondary vortex systems around the bars periodically disturb the freestream end-wall boundary layer facing the blade leading edge. This ultimately influences the end-wall related losses downstream of the blade and governs the overall aerodynamic performance of the blade. Following validation against available experimental data, a systematic variation of flow coefficient and reduced frequency extends the parametric space studied to encompass engine-realistic operating conditions. The high-fidelity simulations reveal the impact of incoming wakes on blade boundary layer losses and wake-induced losses both at the mid-span and within the end-wall regions. Furthermore, by decomposing the total loss generation, the data-rich results shed light on the underlying physical mechanisms driving unsteady losses when applied to phase- and time-averaged flow fields. Secondary losses incurred in the end-wall region show little sensitivity toward unsteadiness associated with incoming wakes and are rather prone to the turbulence levels in the passage. On the other hand, profile losses show high dependency on bar wakes in the absence of wake fogging. While profile losses can be minimized by certain combinations of flow coefficients and reduced frequencies, they remain the dominant source of unsteady loss generation.
- Open Access
- 25 October 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (4) , 1-23
Performance of Rough-Ribbed Low-Pressure Turbine Blades Under Varying Loading and Operating Conditions
Recent research has demonstrated the effectiveness of riblets (streamwise aligned grooves) in reducing the profile loss of low-pressure turbine (LPT) blades under high-lift (HL) loading. In this research, we pursue the efficacy of riblets in reducing the blade profile loss under various design and off-design conditions. We adopt a strategy in which surface roughness is employed in the transitional regime to minimize the separation bubble-related losses and flush-mounted riblets downstream to further mitigate the skin-friction drag and boundary layer losses due to an increase in the turbulent wetted area. Several high-fidelity scale-resolving simulations are carried out to test the efficacy of this ‘rough-ribbed’ LPT blade for loadings ranging from low-lift (LL), HL, and ultra high-lift (UHL) conditions. Furthermore, two exit Reynolds numbers—83,000 and 166,000—pertaining to engine relevant design and off-design conditions, respectively, are considered. The streamwise evolution of skin-friction coefficient and boundary layer integral parameters are compared and contrasted among different test cases. The instantaneous flow features and second-order statistics such as the Reynolds stress and turbulent kinetic energy are analyzed to determine the design and off-design performance of riblets. It is found that the efficacy of scallop-shaped riblets in reducing the profile loss improves with loading. Specifically, the net skin-friction reduction increases from 3.4% under LL to 8% under UHL loading at cruise Re. There is a corresponding reduction in the trailing edge momentum thickness (θTE) from 10% to 15%. A further reduction in θTE is attained from design to off-design Re under UHL loading. Thus, the effect of riblets in reducing mixing losses improves with increasing Re. It is also found that the riblets reduce flow blockage due to boundary layers. Furthermore, the necessity to optimize riblet ramp to achieve skin-friction reduction under off-design conditions is highlighted.
- 25 October 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (4) , 1-23
Open AccessPerformance of Rough-Ribbed Low-Pressure Turbine Blades Under Varying Loading and Operating Conditions
Recent research has demonstrated the effectiveness of riblets (streamwise aligned grooves) in reducing the profile loss of low-pressure turbine (LPT) blades under high-lift (HL) loading. In this research, we pursue the efficacy of riblets in reducing the blade profile loss under various design and off-design conditions. We adopt a strategy in which surface roughness is employed in the transitional regime to minimize the separation bubble-related losses and flush-mounted riblets downstream to further mitigate the skin-friction drag and boundary layer losses due to an increase in the turbulent wetted area. Several high-fidelity scale-resolving simulations are carried out to test the efficacy of this ‘rough-ribbed’ LPT blade for loadings ranging from low-lift (LL), HL, and ultra high-lift (UHL) conditions. Furthermore, two exit Reynolds numbers—83,000 and 166,000—pertaining to engine relevant design and off-design conditions, respectively, are considered. The streamwise evolution of skin-friction coefficient and boundary layer integral parameters are compared and contrasted among different test cases. The instantaneous flow features and second-order statistics such as the Reynolds stress and turbulent kinetic energy are analyzed to determine the design and off-design performance of riblets. It is found that the efficacy of scallop-shaped riblets in reducing the profile loss improves with loading. Specifically, the net skin-friction reduction increases from 3.4% under LL to 8% under UHL loading at cruise Re. There is a corresponding reduction in the trailing edge momentum thickness (θTE) from 10% to 15%. A further reduction in θTE is attained from design to off-design Re under UHL loading. Thus, the effect of riblets in reducing mixing losses improves with increasing Re. It is also found that the riblets reduce flow blockage due to boundary layers. Furthermore, the necessity to optimize riblet ramp to achieve skin-friction reduction under off-design conditions is highlighted.
- 14 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-17
Effects of Riblet Dimensions on the Transitional Boundary Layers Over High-Lift Turbine Blades
Substantial research exists in the literature on reducing the profile loss of transitional boundary layers over low-pressure turbine (LPT) blades via different mechanisms such as freestream turbulence, upstream wakes, and surface roughness. These mechanisms have proven to be beneficial in mitigating the separation bubble-related losses in ultra-high-lift blade designs, despite an increase in the loss due to increased turbulent wetted area (TWA). In this work, we adopt a strategy of employing surface roughness in the transitional regime to minimize the separation bubble-related losses and flush-mounted riblets downstream to further mitigate the skin-friction drag and boundary layer losses due to an increase in the TWA. Several high-fidelity scale-resolving simulations are performed on this “rough-ribbed blade surface” to discern the effect of varying the riblet spacing (s+) and height (h+). The streamwise evolution of skin-friction coefficient, boundary layer integral parameters, and shape factor are compared and contrasted among riblets of different dimensions. The instantaneous flow features and second-order statistics such as the Reynolds stress, turbulent kinetic energy, and its production are analyzed for different test cases to determine the impact of riblets on these quantities. When compared to the roughness alone configuration, the scalloped shape riblets with s+ = 17 and h+ = 22 reduced the net skin-friction drag by 7.3% and the trailing edge momentum thickness by 14.5%, thereby demonstrating the efficacy of riblets in reducing the mixing losses under adverse pressure gradients. Through an analysis of flow blockage introduced by the application of riblets, the deleterious effects of increasing the riblet height along with the necessity of optimizing the riblet ramp are highlighted.
- 14 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-17
Effects of Riblet Dimensions on the Transitional Boundary Layers Over High-Lift Turbine Blades
Substantial research exists in the literature on reducing the profile loss of transitional boundary layers over low-pressure turbine (LPT) blades via different mechanisms such as freestream turbulence, upstream wakes, and surface roughness. These mechanisms have proven to be beneficial in mitigating the separation bubble-related losses in ultra-high-lift blade designs, despite an increase in the loss due to increased turbulent wetted area (TWA). In this work, we adopt a strategy of employing surface roughness in the transitional regime to minimize the separation bubble-related losses and flush-mounted riblets downstream to further mitigate the skin-friction drag and boundary layer losses due to an increase in the TWA. Several high-fidelity scale-resolving simulations are performed on this “rough-ribbed blade surface” to discern the effect of varying the riblet spacing (s+) and height (h+). The streamwise evolution of skin-friction coefficient, boundary layer integral parameters, and shape factor are compared and contrasted among riblets of different dimensions. The instantaneous flow features and second-order statistics such as the Reynolds stress, turbulent kinetic energy, and its production are analyzed for different test cases to determine the impact of riblets on these quantities. When compared to the roughness alone configuration, the scalloped shape riblets with s+ = 17 and h+ = 22 reduced the net skin-friction drag by 7.3% and the trailing edge momentum thickness by 14.5%, thereby demonstrating the efficacy of riblets in reducing the mixing losses under adverse pressure gradients. Through an analysis of flow blockage introduced by the application of riblets, the deleterious effects of increasing the riblet height along with the necessity of optimizing the riblet ramp are highlighted.
- 4 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-29
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part II: The Effect of Roughness on the Performance of a High-Pressure Turbine Blade
Turbine blades generally present surface roughness introduced in the manufacturing process or caused by in-service degradation, which can have a significant impact on aero-thermal performance. A better understanding of the fundamental physical mechanisms arising from the interaction between the roughness and the turbine flow at engine-relevant conditions can provide insights for the design of blades with improved efficiency and longer operational life. To this end, a high-fidelity numerical framework combining a well-validated solver for direct numerical simulation and a second-order accurate immersed boundary method is employed to predict roughness-induced aero-thermal effects on an LS89 high-pressure turbine (HPT) blade at engine-relevant conditions. Different amplitudes and distributions of surface roughness are investigated and a reference smooth-blade simulation under the same flow conditions is conducted for comparison. Roughness of increasing amplitude progressively shifts the blade suction side boundary layer transition upstream, producing larger values of the turbulent kinetic energy and higher total wake losses. The on-surface data-capturing capabilities of the numerical framework provide direct measurements of the heat flux and the skin friction coefficient, hence offering quantitative information between the surface topology and engineering-relevant performance parameters. This work may provide a benchmark for future numerical studies of turbomachinery flows with roughness.
- 4 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-29
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part II: The Effect of Roughness on the Performance of a High-Pressure Turbine Blade
Turbine blades generally present surface roughness introduced in the manufacturing process or caused by in-service degradation, which can have a significant impact on aero-thermal performance. A better understanding of the fundamental physical mechanisms arising from the interaction between the roughness and the turbine flow at engine-relevant conditions can provide insights for the design of blades with improved efficiency and longer operational life. To this end, a high-fidelity numerical framework combining a well-validated solver for direct numerical simulation and a second-order accurate immersed boundary method is employed to predict roughness-induced aero-thermal effects on an LS89 high-pressure turbine (HPT) blade at engine-relevant conditions. Different amplitudes and distributions of surface roughness are investigated and a reference smooth-blade simulation under the same flow conditions is conducted for comparison. Roughness of increasing amplitude progressively shifts the blade suction side boundary layer transition upstream, producing larger values of the turbulent kinetic energy and higher total wake losses. The on-surface data-capturing capabilities of the numerical framework provide direct measurements of the heat flux and the skin friction coefficient, hence offering quantitative information between the surface topology and engineering-relevant performance parameters. This work may provide a benchmark for future numerical studies of turbomachinery flows with roughness.
- 4 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-37
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part I: Methodology and Challenges
High-fidelity simulation of transitional and turbulent flows over multi-scale surface roughness presents several challenges. For instance, the complex and irregular geometrical nature of surface roughness makes it impractical to employ conforming structured grids, commonly adopted in large-scale numerical simulations due to their high computational efficiency. One possible solution to overcome this problem is offered by immersed boundary methods, which allow wall boundary conditions to be enforced on grids that do not conform to the geometry of the solid boundary. To this end, a three-dimensional, second-order accurate boundary data immersion method (BDIM) is adopted. A novel mapping algorithm that can be applied to general three-dimensional surfaces is presented, together with a newly developed data-capturing methodology to extract and analyze on-surface flow quantities of interest. A rigorous procedure to compute gradient quantities such as the wall shear stress and the heat flux on complex non-conforming geometries is also introduced. The new framework is validated by performing a direct numerical simulation (DNS) of fully developed turbulent channel flow over sinusoidal egg-carton roughness in a minimal-span domain. For this canonical case, the averaged streamwise velocity profiles are compared against results from the literature obtained with a body-fitted grid. General guidelines on the BDIM resolution requirements for multi-scale roughness simulation are given. Momentum and energy balance methods are used to validate the calculation of the overall skin friction and heat transfer at the wall. The BDIM is then employed to investigate the effect of irregular homogeneous surface roughness on the performance of an LS-89 high-pressure turbine blade at engine-relevant conditions using DNS. This is the first application of the BDIM to realize multi-scale roughness for transitional flow in transonic conditions in the context of high-pressure turbines. The methodology adopted to generate the desired roughness distribution and to apply it to the reference blade geometry is introduced. The results are compared to the case of an equivalent smooth blade.
- 4 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-37
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part I: Methodology and Challenges
High-fidelity simulation of transitional and turbulent flows over multi-scale surface roughness presents several challenges. For instance, the complex and irregular geometrical nature of surface roughness makes it impractical to employ conforming structured grids, commonly adopted in large-scale numerical simulations due to their high computational efficiency. One possible solution to overcome this problem is offered by immersed boundary methods, which allow wall boundary conditions to be enforced on grids that do not conform to the geometry of the solid boundary. To this end, a three-dimensional, second-order accurate boundary data immersion method (BDIM) is adopted. A novel mapping algorithm that can be applied to general three-dimensional surfaces is presented, together with a newly developed data-capturing methodology to extract and analyze on-surface flow quantities of interest. A rigorous procedure to compute gradient quantities such as the wall shear stress and the heat flux on complex non-conforming geometries is also introduced. The new framework is validated by performing a direct numerical simulation (DNS) of fully developed turbulent channel flow over sinusoidal egg-carton roughness in a minimal-span domain. For this canonical case, the averaged streamwise velocity profiles are compared against results from the literature obtained with a body-fitted grid. General guidelines on the BDIM resolution requirements for multi-scale roughness simulation are given. Momentum and energy balance methods are used to validate the calculation of the overall skin friction and heat transfer at the wall. The BDIM is then employed to investigate the effect of irregular homogeneous surface roughness on the performance of an LS-89 high-pressure turbine blade at engine-relevant conditions using DNS. This is the first application of the BDIM to realize multi-scale roughness for transitional flow in transonic conditions in the context of high-pressure turbines. The methodology adopted to generate the desired roughness distribution and to apply it to the reference blade geometry is introduced. The results are compared to the case of an equivalent smooth blade.