Oleksandr Uchitel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oleksandr Uchitel has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Serhii Shved
State University of Economics and Technology
2 shared publications - Світлана Олійник
Krivoy Rog National University
2 shared publications - D.P. Vlasenkov
Kryvyi Rih professional college of State University «Kyiv Aviation Institute», Ukraine
1 shared publication - Hanna Panchenko
State University of Economics and Technology
1 shared publication I.V. Zaselskyi
State University of Economics and Technology
1 shared publication- Ihor Zaselskiy
State University of Economics and Technology
1 shared publication
Latest Publications
- Open Access
- 26 March 2026
- Published by SHEI Pryazovskyi State Technical University
- Vol. 1 (53) , 154-161
Industrial studies of the operation of vibrating screening machines with an impact-action screening surface
The modern development of the metallurgical industry is characterized by increasing requirements for energy efficiency and reduction of carbon emissions in line with the Green Steel transition and the European Green Deal. One of the key factors affecting blast furnace efficiency is the granulometric composition of burden materials, which determines gas-dynamic conditions and fuel consumption. Therefore, improving screening efficiency is an important scientific and practical task. The aim of the study is to determine the influence of a vibration-impact operating mode of vibrating screens on technological performance, stabilization of granulometric composition, and mechanical strength of agglomerate under industrial conditions. The methodology is based on industrial experiments carried out on vibrating screens with a freely supported sieve surface operating in a vibration-impact mode. The evaluation included transport capacity, screening efficiency, sieve clogging, particle strength, and synchronization of vibration exciters. The results show that the vibration-impact mode reduces transport capacity by 17…56%, while significantly improving process quality indicators. In particular, sieve clogging decreases by up to 6 times and screening efficiency increases by 43% compared to the conventional mode under identical dynamic parameters. It is established that stabilization of granulometric composition is most effective at vibration acceleration levels of 30…40 m/s², which allows reducing the content of the –5 mm fraction by 5%. Additionally, an increase in vibration acceleration by 11% leads to a 17% decrease in the phase shift of imbalance masses, indicating improved synchronization and reduced transient processes. The scientific novelty lies in the industrial confirmation of the effectiveness of the vibration-impact screening mode with a freely supported sieve surface. The practical significance consists in improving raw material preparation quality and reducing energy consumption in metallurgical processes. Further research should focus on optimization of design and operating parameters
- 26 March 2026
- Published by SHEI Pryazovskyi State Technical University
- Vol. 1 (53) , 154-161
Open AccessIndustrial studies of the operation of vibrating screening machines with an impact-action screening surface
The modern development of the metallurgical industry is characterized by increasing requirements for energy efficiency and reduction of carbon emissions in line with the Green Steel transition and the European Green Deal. One of the key factors affecting blast furnace efficiency is the granulometric composition of burden materials, which determines gas-dynamic conditions and fuel consumption. Therefore, improving screening efficiency is an important scientific and practical task. The aim of the study is to determine the influence of a vibration-impact operating mode of vibrating screens on technological performance, stabilization of granulometric composition, and mechanical strength of agglomerate under industrial conditions. The methodology is based on industrial experiments carried out on vibrating screens with a freely supported sieve surface operating in a vibration-impact mode. The evaluation included transport capacity, screening efficiency, sieve clogging, particle strength, and synchronization of vibration exciters. The results show that the vibration-impact mode reduces transport capacity by 17…56%, while significantly improving process quality indicators. In particular, sieve clogging decreases by up to 6 times and screening efficiency increases by 43% compared to the conventional mode under identical dynamic parameters. It is established that stabilization of granulometric composition is most effective at vibration acceleration levels of 30…40 m/s², which allows reducing the content of the –5 mm fraction by 5%. Additionally, an increase in vibration acceleration by 11% leads to a 17% decrease in the phase shift of imbalance masses, indicating improved synchronization and reduced transient processes. The scientific novelty lies in the industrial confirmation of the effectiveness of the vibration-impact screening mode with a freely supported sieve surface. The practical significance consists in improving raw material preparation quality and reducing energy consumption in metallurgical processes. Further research should focus on optimization of design and operating parameters
- Open Access
- 22 September 2025
- Published by Khmelnytskyi National University in Problems of tribology
- Vol. 30 (3/117) , 41-48
Dynamic processes in surface layers of parts as a source of their multicycle failure under friction and wear
During the operation of various machines and mechanisms, oscillatory movements may occur, excited by a non-stationary friction characteristic. These oscillations appear either at the contact area of two parts or in the zone located ahead of the moving part. In the contact area, a non-stationary friction force develops, leading to self-excited oscillations of the contact surface and to the occurrence of parametric oscillations in the area ahead of the active punch. At certain ratios of slip velocities and part movement speeds, self-excited and parametric motions may appear or disappear, as well as intensify or weaken. These oscillations are one of the causes of uncontrolled surface roughness (deformational), cracking, and spalling of interacting parts, as well as significant dynamic components during the loading of actuating, drive, and power mechanisms. Frictional and parametric oscillations in the surface layers of parts with deformation wave formation create residual plastic sinusoidal metal layers, which are sheared off during the interaction of parts. Due to the dynamic nature of interaction during friction, the forces acting in the contact plane (longitudinal) exceed the critical Euler force, which is a parametric load, and in some cases lead to dangerous parametric resonance. The work defines the frequency range near the parametric resonance, which is the area of dynamic instability ahead of the moving punch. The formulated and partially solved problem considers frictional and parametric oscillations during the interaction of parts, which lead to the formation of deformation waves.
- 22 September 2025
- Published by Khmelnytskyi National University in Problems of tribology
- Vol. 30 (3/117) , 41-48
Open AccessDynamic processes in surface layers of parts as a source of their multicycle failure under friction and wear
During the operation of various machines and mechanisms, oscillatory movements may occur, excited by a non-stationary friction characteristic. These oscillations appear either at the contact area of two parts or in the zone located ahead of the moving part. In the contact area, a non-stationary friction force develops, leading to self-excited oscillations of the contact surface and to the occurrence of parametric oscillations in the area ahead of the active punch. At certain ratios of slip velocities and part movement speeds, self-excited and parametric motions may appear or disappear, as well as intensify or weaken. These oscillations are one of the causes of uncontrolled surface roughness (deformational), cracking, and spalling of interacting parts, as well as significant dynamic components during the loading of actuating, drive, and power mechanisms. Frictional and parametric oscillations in the surface layers of parts with deformation wave formation create residual plastic sinusoidal metal layers, which are sheared off during the interaction of parts. Due to the dynamic nature of interaction during friction, the forces acting in the contact plane (longitudinal) exceed the critical Euler force, which is a parametric load, and in some cases lead to dangerous parametric resonance. The work defines the frequency range near the parametric resonance, which is the area of dynamic instability ahead of the moving punch. The formulated and partially solved problem considers frictional and parametric oscillations during the interaction of parts, which lead to the formation of deformation waves.
- Open Access
- 25 October 2023
- Published by State University Of Economics And Technology in Economics and technical engineering
- Vol. 1 (1) , 115-125
Дослідження варіантів удосконалення ґрунтового насосу для залізорудної пульпи
For pumping iron ore slurry, many mining and processing plants in Ukraine use an 8Gr-8m submersible pump. As shown its performance under the conditions of pumping pulp with a density of up to 1400 kg/m 3, they do not correspond to the passport data, and this is mainly due to concerns the flow chamber, the service life of which is reduced by almost 2 times compared to the manufacturer’s suggested service life. Therefore, the aim of the work was to study options for improving the design of the flow part of the 8Gr-8m pump, which would significantly increase its service life. To achieve this goal and obtain the required results we chose a method based on hydrodynamic studies using CAD technologies, for which, in addition to the 3D model of the existing pump, four more different designs were developed. The proposed designs were studied using SOLIDWORKS Flow Simulation program, which allowed us to model the movement of the pulp in the pump flow chamber. The parameters for modeling were selected based on pump operation conditions at the iron ore pulp pumping section concentrator of the Southern Mining and Processing Plant in Kryvyi Rih. The analysis of the results showed that the best performance is provided by a composite impeller with 4 blades of complex shape, low profile, which has a good pumping characteristic with a minimum tendency to wear. The design of the removable impeller is made of cast steel and lined with rubber, it has 4 blades with rounded front edges. The distance along the armhole between the side washers is 50 mm, it is unchanged. The pressure surface of the blade has a short ledge. The distribution zone is a high layer of small diameter. The inlet washer is flat, but with a high flap on the diffuser. The diameter of the wheel is 520 mm, and its weight is 70 kg. Based on this model, animproved design was proposed for of the flowing part of the 8GR-8m pump impeller and its lining lining based on SCS-30ARKM-15 rubber, which in combination with technical solutions allows to more effectively prevent wear of the studied unit and leads to increase its service life.
- 25 October 2023
- Published by State University Of Economics And Technology in Economics and technical engineering
- Vol. 1 (1) , 115-125
Open AccessДослідження варіантів удосконалення ґрунтового насосу для залізорудної пульпи
For pumping iron ore slurry, many mining and processing plants in Ukraine use an 8Gr-8m submersible pump. As shown its performance under the conditions of pumping pulp with a density of up to 1400 kg/m 3, they do not correspond to the passport data, and this is mainly due to concerns the flow chamber, the service life of which is reduced by almost 2 times compared to the manufacturer’s suggested service life. Therefore, the aim of the work was to study options for improving the design of the flow part of the 8Gr-8m pump, which would significantly increase its service life. To achieve this goal and obtain the required results we chose a method based on hydrodynamic studies using CAD technologies, for which, in addition to the 3D model of the existing pump, four more different designs were developed. The proposed designs were studied using SOLIDWORKS Flow Simulation program, which allowed us to model the movement of the pulp in the pump flow chamber. The parameters for modeling were selected based on pump operation conditions at the iron ore pulp pumping section concentrator of the Southern Mining and Processing Plant in Kryvyi Rih. The analysis of the results showed that the best performance is provided by a composite impeller with 4 blades of complex shape, low profile, which has a good pumping characteristic with a minimum tendency to wear. The design of the removable impeller is made of cast steel and lined with rubber, it has 4 blades with rounded front edges. The distance along the armhole between the side washers is 50 mm, it is unchanged. The pressure surface of the blade has a short ledge. The distribution zone is a high layer of small diameter. The inlet washer is flat, but with a high flap on the diffuser. The diameter of the wheel is 520 mm, and its weight is 70 kg. Based on this model, animproved design was proposed for of the flowing part of the 8GR-8m pump impeller and its lining lining based on SCS-30ARKM-15 rubber, which in combination with technical solutions allows to more effectively prevent wear of the studied unit and leads to increase its service life.
- 27 September 2023
- Published by State University "Kyiv Aviation Institute" in Problems of Friction and Wear
- No. 3(100),p. 49-64
ЕРОЗІЙНИЙ ЗНОС ВАНТАЖОНЕСУЧОГО ПОЛОТНА ОБПАЛЮВАЛЬНИХ МАШИН ПІД ВПЛИВОМ ЗАЛІЗОРУДНИХ ОКАТИШІВ
The load-carrying belt of conveyor machines for clods of iron ore concentrate operates in a complex, aggressive dust and gas environment and cyclic "heating-cooling" modes. At the same time, the constituent elements of the load-bearing fabric - gratings also work under the influence of shock and abrasive loads, which leads to their intensive wear, as well as an increase in the regulated working gaps between adjacent gratings, and, therefore, to their premature replacement. In order to predict the degree of wear of the working surfaces of parts (grills), numerical models have been developed at the micro, macro, and meso levels. These models work in various combinations, but in the given conditions of operation of burning machines, due to the specifics of their work, meso- and micro-models rarely appear. The results of the analysis of the defects of the grates, which have failed, indicate the manifestation of macro-models, the schematization of which takes place mainly in the form of an erosive wear model. On the basis of macro models, Bitter's dependences were modified to calculate the degree of erosive wear of grates, and it was also established that to significantly reduce the degree of wear of pallets, it is recommended to use drum-type loading devices that ensure unloading of material with an angle of attack α=35÷45°. At the same time, the best recommended material for grates is steel 30Х14Г8Ю2Л.
- 27 September 2023
- Published by State University "Kyiv Aviation Institute" in Problems of Friction and Wear
- No. 3(100),p. 49-64
ЕРОЗІЙНИЙ ЗНОС ВАНТАЖОНЕСУЧОГО ПОЛОТНА ОБПАЛЮВАЛЬНИХ МАШИН ПІД ВПЛИВОМ ЗАЛІЗОРУДНИХ ОКАТИШІВ
The load-carrying belt of conveyor machines for clods of iron ore concentrate operates in a complex, aggressive dust and gas environment and cyclic "heating-cooling" modes. At the same time, the constituent elements of the load-bearing fabric - gratings also work under the influence of shock and abrasive loads, which leads to their intensive wear, as well as an increase in the regulated working gaps between adjacent gratings, and, therefore, to their premature replacement. In order to predict the degree of wear of the working surfaces of parts (grills), numerical models have been developed at the micro, macro, and meso levels. These models work in various combinations, but in the given conditions of operation of burning machines, due to the specifics of their work, meso- and micro-models rarely appear. The results of the analysis of the defects of the grates, which have failed, indicate the manifestation of macro-models, the schematization of which takes place mainly in the form of an erosive wear model. On the basis of macro models, Bitter's dependences were modified to calculate the degree of erosive wear of grates, and it was also established that to significantly reduce the degree of wear of pallets, it is recommended to use drum-type loading devices that ensure unloading of material with an angle of attack α=35÷45°. At the same time, the best recommended material for grates is steel 30Х14Г8Ю2Л.