Joo Young Bae
Joo Young Bae has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Mi-Song Kim
Electronic Convergence Materials & Device Research Center, Korea Electronics Technology Institute, Seongnam, 13509, Korea
5 shared publications - Won Sik Hong
Electronic Convergence Materials & Device Research Center, Korea Electronics Technology Institute, Seongnam, 13509, Korea
5 shared publications Jeong Tak Moon
MK Electron Co., Ltd.,Solder Development Team, RD Center,Gyeonggi-do,Korea,17030
3 shared publications- So-Hee Hyun
Electronic Convergence Materials & Device Research Center KETI 13509 Seongnam Korea
3 shared publications Seul Gi Lee
2 shared publicationsYoung-Woo Lee
2 shared publications
Latest Publications
- 3 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 609-615
Thermal Cycling Performance of Heterogeneous Sn-Ag-Cu Solder Joint with Minor Elements Addition
- 3 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 609-615
Thermal Cycling Performance of Heterogeneous Sn-Ag-Cu Solder Joint with Minor Elements Addition
- Open Access
- 31 August 2024
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 42 (4) , 378-387
Bonding Properties of Package-on-Package Stack Interconnection Using by 150 ㎛ Height Copper Posts
In this study, we used copper (Cu) posts, plated to a height of 150 μm, as interconnections to form electrodes between different package layers. The upper layer consisted of a chip-scale package (CSP), while the lower layer was made up of a flip chip-chip scale package (FCCSP). We plated a Cu post on the side of FCCSP substrate, and produced the FCCSP package by thermo-compression (TC) bonding with copper pillar solder bumps on the center of substrate. The surface of the bottom electrode for the upper CSP received a surface finish of electroless nickel, electroless palladium, and immersion gold (ENEPIG). The bonding surface of the lower FCCSP was the bare Cu surface of the epoxy-molded Cu post. The PoP joining process used a vacuum reflow process with solder paste and solder balls. To understand the package joint's characteristics, we measured voids and shear strength, and analyzed the cross-sectional microstructure. The temperature profile used in the PoP joining process demonstrated optimal joint characteristics with a joint void content of 2.3% and a joint strength of approximately 44 MPa when formic acid was utilized and the activation preheating time was extended. Cross-sectional warpage analysis of the PoP package revealed a minimal difference of approximately 31 μm between the center and the ends. This study successfully developed a stacked package with a PoP structure using Cu Post, and the bonding process was optimized to minimize warpage in the PoP package.
- 31 August 2024
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 42 (4) , 378-387
Open AccessBonding Properties of Package-on-Package Stack Interconnection Using by 150 ㎛ Height Copper Posts
In this study, we used copper (Cu) posts, plated to a height of 150 μm, as interconnections to form electrodes between different package layers. The upper layer consisted of a chip-scale package (CSP), while the lower layer was made up of a flip chip-chip scale package (FCCSP). We plated a Cu post on the side of FCCSP substrate, and produced the FCCSP package by thermo-compression (TC) bonding with copper pillar solder bumps on the center of substrate. The surface of the bottom electrode for the upper CSP received a surface finish of electroless nickel, electroless palladium, and immersion gold (ENEPIG). The bonding surface of the lower FCCSP was the bare Cu surface of the epoxy-molded Cu post. The PoP joining process used a vacuum reflow process with solder paste and solder balls. To understand the package joint's characteristics, we measured voids and shear strength, and analyzed the cross-sectional microstructure. The temperature profile used in the PoP joining process demonstrated optimal joint characteristics with a joint void content of 2.3% and a joint strength of approximately 44 MPa when formic acid was utilized and the activation preheating time was extended. Cross-sectional warpage analysis of the PoP package revealed a minimal difference of approximately 31 μm between the center and the ends. This study successfully developed a stacked package with a PoP structure using Cu Post, and the bonding process was optimized to minimize warpage in the PoP package.
- Open Access
- 30 April 2024
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 42 (2) , 174-183
Thermal Cycling Performance of Heterogeneous Solder Ball Joints with Sn-3.0Ag-0.5Cu and Sn-0.75Cu(-Ni,Bi) Solder Ball Composition for BGA Package
1) BGA/솔더 접합부와 PCB/솔더 접합부에서 각각 (Ni,Cu)6Sn5, Cu6Sn5 IMC 층이 형성되었으며 솔더 모재 내에 (Ni,Cu)6Sn5, Cu6Sn5, Ag3Sn가 분포함을 확인하였다.
- 30 April 2024
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 42 (2) , 174-183
Open AccessThermal Cycling Performance of Heterogeneous Solder Ball Joints with Sn-3.0Ag-0.5Cu and Sn-0.75Cu(-Ni,Bi) Solder Ball Composition for BGA Package
1) BGA/솔더 접합부와 PCB/솔더 접합부에서 각각 (Ni,Cu)6Sn5, Cu6Sn5 IMC 층이 형성되었으며 솔더 모재 내에 (Ni,Cu)6Sn5, Cu6Sn5, Ag3Sn가 분포함을 확인하였다.
- Open Access
- 31 December 2023
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 41 (6) , 519-527
Electrochemical Metallic Ion Migration Property of Multi-Layer Ceramic Capacitor for Car Electronics
As the use of electrical components in automobiles increases, the occurrence of electorchemical metallic ion migration (ECM), which is one of the causes of various failures in electrical components, is also increasing. Therefore, in this study, 1608 MLCC chip components were used for temperature-humidity-bias (THB) tests at 65℃/85%R.H., 65℃/95%R.H., and 85℃/85%R.H. Three types of THB tests were conducted for 2,934 h. For the THB test, voltages of 3.3, 12 and 24 V were applied, and real-time resistance of MLCCs were measured at every 40 mms intervals. During the ECM test, the ECM occurrence time was measured by monitoring the insulation resistance of between the electrode of MLCC under each THB test conditions. The failure criteria for ECM occurrence were 106 Ω or less, and the time when it occurred more than twice was judged as the ECM failure criteria. Based on the ECM occurrence time, the mean life time of ECM occurrence according to temperature, humidity and applied voltage conditions was derived through Weibull statistical analysis. Finally, we compared and analyzed the sensitivity of MLCC components to ECM generation under use environment of automotive electronics.
- 31 December 2023
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 41 (6) , 519-527
Open AccessElectrochemical Metallic Ion Migration Property of Multi-Layer Ceramic Capacitor for Car Electronics
As the use of electrical components in automobiles increases, the occurrence of electorchemical metallic ion migration (ECM), which is one of the causes of various failures in electrical components, is also increasing. Therefore, in this study, 1608 MLCC chip components were used for temperature-humidity-bias (THB) tests at 65℃/85%R.H., 65℃/95%R.H., and 85℃/85%R.H. Three types of THB tests were conducted for 2,934 h. For the THB test, voltages of 3.3, 12 and 24 V were applied, and real-time resistance of MLCCs were measured at every 40 mms intervals. During the ECM test, the ECM occurrence time was measured by monitoring the insulation resistance of between the electrode of MLCC under each THB test conditions. The failure criteria for ECM occurrence were 106 Ω or less, and the time when it occurred more than twice was judged as the ECM failure criteria. Based on the ECM occurrence time, the mean life time of ECM occurrence according to temperature, humidity and applied voltage conditions was derived through Weibull statistical analysis. Finally, we compared and analyzed the sensitivity of MLCC components to ECM generation under use environment of automotive electronics.
- Open Access
- 31 October 2023
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 41 (5) , 379-386
Bonding Property of Middle Temperature Sn-Ag-Cu Solder Ball Joint of Ball Grid Array Package
Alloying effects of Nickel and Bismuth in SAC solder to achieve mechanical and microstructural evolution were investigated by comparing three different chemical composition of solders. Sn-3.0Ag-0.5Cu (SAC305) is the most commonly used for Pb-free solder and solder balls are based on Sn-Ag-Cu alloy composition. Compositions of solder balls were Sn-3.0Ag-0.5Cu (SAC305), Sn-1.2Ag-0.5Cu-0.05Ni (SAC1205N) and Sn-Ag-Cu-Ni-Bi based solder (SACNB). Organic solderability preservative (OSP) surface finished substrate, ball grid array (BGA) package arranged by 300 ㎛ diameter solder ball and Type 4 solder paste were used. Solder ball shear test of the BGA package was conducted before the reflow soldering. Board level package bonding process was carried out by hot air reflow soldering. Void content of the BGA solder joint was investigated after soldering. The microstructure evolution before and after thermal cycle test (TCT) was observed using scanning eletron microscopy (SEM) and energy dispersive spectroscopy (EDS). After TCT, intermetallic compound (IMC) refinement and solid solution strengthening effects of Bi element addition were observed in the solder matrix, and also any segregation of Bi element was not founded. Based on these result, it was found that the solder joint reliability of the middle and low temperature solder joints was improved.
- 31 October 2023
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 41 (5) , 379-386
Open AccessBonding Property of Middle Temperature Sn-Ag-Cu Solder Ball Joint of Ball Grid Array Package
Alloying effects of Nickel and Bismuth in SAC solder to achieve mechanical and microstructural evolution were investigated by comparing three different chemical composition of solders. Sn-3.0Ag-0.5Cu (SAC305) is the most commonly used for Pb-free solder and solder balls are based on Sn-Ag-Cu alloy composition. Compositions of solder balls were Sn-3.0Ag-0.5Cu (SAC305), Sn-1.2Ag-0.5Cu-0.05Ni (SAC1205N) and Sn-Ag-Cu-Ni-Bi based solder (SACNB). Organic solderability preservative (OSP) surface finished substrate, ball grid array (BGA) package arranged by 300 ㎛ diameter solder ball and Type 4 solder paste were used. Solder ball shear test of the BGA package was conducted before the reflow soldering. Board level package bonding process was carried out by hot air reflow soldering. Void content of the BGA solder joint was investigated after soldering. The microstructure evolution before and after thermal cycle test (TCT) was observed using scanning eletron microscopy (SEM) and energy dispersive spectroscopy (EDS). After TCT, intermetallic compound (IMC) refinement and solid solution strengthening effects of Bi element addition were observed in the solder matrix, and also any segregation of Bi element was not founded. Based on these result, it was found that the solder joint reliability of the middle and low temperature solder joints was improved.