Theodore Mouratidis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Theodore Mouratidis has a total of 105 co-authors. Here are the top co-authors by number of shared publications:
Dennis G Whyte
Plasma Science and Fusion Center, Massachusetts Institute of Technology, NW17-288, 77 Massachusetts Avenue, Cambridge, Massachusetts, 02139, UNITED STATES
3 shared publications- Amy Watterson
Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, MA, USA
2 shared publications - Brian LaBombard
MIT Plasma Science and Fusion Center, Cambridge, MA, United States of America
2 shared publications - Daniel Nash
Thea Energy, Inc., Kearny, NJ, USA
2 shared publications - Dennis G. Whyte
Massachusetts Institute of Technology, Cambridge, MA, United States of America
2 shared publications J. P. Muncks
Commonwealth Fusion Systems, Devens, MA, USA
2 shared publications
Latest Publications
- Top Cited PapersOpen Access
- 22 August 2024
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 66 (10) , 105006
MANTA: a negative-triangularity NASEM-compliant fusion pilot plant
The MANTA (Modular Adjustable Negative Triangularity ARC-class) design study investigated how negative-triangularity (NT) may be leveraged in a compact, fusion pilot plant (FPP) to take a ‘power-handling first’ approach. The result is a pulsed, radiative, ELM-free tokamak that satisfies and exceeds the FPP requirements described in the 2021 National Academies of Sciences, Engineering, and Medicine (NASEM) report ‘Bringing Fusion to the U.S. Grid’ (2021 Bringing Fusion to the U.S. Grid). A self-consistent integrated modeling workflow predicts a fusion power of 450 MW and a plasma gain of 11.5 with only 23.5 MW of power to the scrape-off layer (SOL). This low P SOL together with impurity seeding and high density at the separatrix results in a peak heat flux of just 2.8 MW m−2. MANTA’s high aspect ratio provides space for a large central solenoid (CS), resulting in ∼15 minute inductive pulses. In spite of the high B fields on the CS and the other REBCO-based magnets, the electromagnetic stresses remain below structural and critical current density limits. Iterative optimization of neutron shielding and tritium breeding blanket yield tritium self-sufficiency with a breeding ratio of 1.15, a blanket power multiplication factor of 1.11, toroidal field coil lifetimes of 3100 ± 400 MW · yr, and poloidal field coil lifetimes of at least 890 ± 40 MW · yr. Following balance of plant modeling, MANTA is projected to generate 90 MW of net electricity at an electricity gain factor of ∼ 2.4 . Systems-level economic analysis estimates an overnight cost of US$3.4 billion, meeting the NASEM FPP requirement that this first-of-a-kind be less than US$5 billion. The toroidal field coil cost and replacement time are the most critical upfront and lifetime cost drivers, respectively.
- 22 August 2024
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 66 (10) , 105006
Top Cited PapersOpen AccessMANTA: a negative-triangularity NASEM-compliant fusion pilot plant
The MANTA (Modular Adjustable Negative Triangularity ARC-class) design study investigated how negative-triangularity (NT) may be leveraged in a compact, fusion pilot plant (FPP) to take a ‘power-handling first’ approach. The result is a pulsed, radiative, ELM-free tokamak that satisfies and exceeds the FPP requirements described in the 2021 National Academies of Sciences, Engineering, and Medicine (NASEM) report ‘Bringing Fusion to the U.S. Grid’ (2021 Bringing Fusion to the U.S. Grid). A self-consistent integrated modeling workflow predicts a fusion power of 450 MW and a plasma gain of 11.5 with only 23.5 MW of power to the scrape-off layer (SOL). This low P SOL together with impurity seeding and high density at the separatrix results in a peak heat flux of just 2.8 MW m−2. MANTA’s high aspect ratio provides space for a large central solenoid (CS), resulting in ∼15 minute inductive pulses. In spite of the high B fields on the CS and the other REBCO-based magnets, the electromagnetic stresses remain below structural and critical current density limits. Iterative optimization of neutron shielding and tritium breeding blanket yield tritium self-sufficiency with a breeding ratio of 1.15, a blanket power multiplication factor of 1.11, toroidal field coil lifetimes of 3100 ± 400 MW · yr, and poloidal field coil lifetimes of at least 890 ± 40 MW · yr. Following balance of plant modeling, MANTA is projected to generate 90 MW of net electricity at an electricity gain factor of ∼ 2.4 . Systems-level economic analysis estimates an overnight cost of US$3.4 billion, meeting the NASEM FPP requirement that this first-of-a-kind be less than US$5 billion. The toroidal field coil cost and replacement time are the most critical upfront and lifetime cost drivers, respectively.
- 2 April 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (5) , 055001
Performance degradation due to thermal cycling in soldered Faraday and SuperPower HTS tape stacks
Soldering stacks of high temperature superconducting (HTS) tapes results in a current carrying matrix with high electrical, thermal, and mechanical stability. In some applications, these tape stacks may be exposed to elevated temperatures during thermal heat cycles. Previous research on thermal degradation of high temperature superconductors has been performed with isolated crystals or individual HTS tapes, showing that oxygen-out diffusion from the rare-earth barium copper oxide (REBCO) results in a reduction of the superconducting performance. In this work, the performance of Pb 37 Sn 63 soldered HTS tape stacks with thermal cycling to 170 ∘ C is quantified through determination of the critical current Ic , the n-value, the linear resistance R in the pre-transition region of the tape stack current–voltage (I–V) traces, and the diffusion coefficient D associated with oxygen-out diffusion. The effect of tape manufacturer and nickel electroplating were considered; three soldered stacks each of unplated Faraday, nickel electroplated Faraday, unplated SuperPower, and nickel electroplated SuperPower tapes were fabricated. Across 20–30 one hour thermal cycles, there are no significant differences in degradation profiles observed between the unplated and nickel electroplated tape stacks for a given manufacturer. There is however a marked difference in degradation profiles observed between the SuperPower and Faraday tape stacks. For the unplated and plated SuperPower tape stacks, the degradation in Ic generally follows the model to describe oxygen-out diffusion from the superconducting REBCO layer. Significantly less degradation is observed in the unplated and plated Faraday tape stacks, and in some sections Ic even increases slightly across cycles. Further, cases of increasing Ic accompanied with decreasing n are observed, a decoupling between the two parameters. Across all samples, the linear resistance was highest in current-redistribution regions near the leads. Consistent with the model of oxygen-out diffusion and the formation of an increasingly wide oxygen deficient layer in the REBCO, the linear resistance increased with cycle number.
- 2 April 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (5) , 055001
Performance degradation due to thermal cycling in soldered Faraday and SuperPower HTS tape stacks
Soldering stacks of high temperature superconducting (HTS) tapes results in a current carrying matrix with high electrical, thermal, and mechanical stability. In some applications, these tape stacks may be exposed to elevated temperatures during thermal heat cycles. Previous research on thermal degradation of high temperature superconductors has been performed with isolated crystals or individual HTS tapes, showing that oxygen-out diffusion from the rare-earth barium copper oxide (REBCO) results in a reduction of the superconducting performance. In this work, the performance of Pb 37 Sn 63 soldered HTS tape stacks with thermal cycling to 170 ∘ C is quantified through determination of the critical current Ic , the n-value, the linear resistance R in the pre-transition region of the tape stack current–voltage (I–V) traces, and the diffusion coefficient D associated with oxygen-out diffusion. The effect of tape manufacturer and nickel electroplating were considered; three soldered stacks each of unplated Faraday, nickel electroplated Faraday, unplated SuperPower, and nickel electroplated SuperPower tapes were fabricated. Across 20–30 one hour thermal cycles, there are no significant differences in degradation profiles observed between the unplated and nickel electroplated tape stacks for a given manufacturer. There is however a marked difference in degradation profiles observed between the SuperPower and Faraday tape stacks. For the unplated and plated SuperPower tape stacks, the degradation in Ic generally follows the model to describe oxygen-out diffusion from the superconducting REBCO layer. Significantly less degradation is observed in the unplated and plated Faraday tape stacks, and in some sections Ic even increases slightly across cycles. Further, cases of increasing Ic accompanied with decreasing n are observed, a decoupling between the two parameters. Across all samples, the linear resistance was highest in current-redistribution regions near the leads. Consistent with the model of oxygen-out diffusion and the formation of an increasingly wide oxygen deficient layer in the REBCO, the linear resistance increased with cycle number.
- Open Access
- 22 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (2) , 1-15
Design, Fabrication, and Assembly of the SPARC Toroidal Field Model Coil
The SPARC Toroidal Field Model Coil (TFMC) is the first large-scale (∼3 m), high-field (∼20 T) superconducting fusion magnet based on Rare Earth Yttrium Barium Copper Oxide (REBCO). Weighing 10,058 kg and utilizing 270 km of REBCO, the TFMC is a non-insulated, stack-in-plate style superconducting magnet. It has three main components: (1) the winding pack; (2) the structural case; and (3) the case extensions, or plena. The winding pack is composed of sixteen single pancakes with two termination plates top and bottom. The pancakes are Nitronic 40 radial plates machined with spiral channels on one side for the REBCO tape stack and single-pass channels on the opposite side for supercritical helium coolant. After assembly, each pancake undergoes a vacuum-pressure impregnation solder process to provide good mechanical protection of the REBCO tape stack and efficient thermal and electrical connectivity within each pancake. The pancakes are bolted along the inner and outer perimeter to provide mechanical and thermal connectivity while inter-pancake joints provide low resistance current transfer between pancakes. The top and bottom termination plates facilitate electrical connection to a superconducting feeder system. Embedded throughout the winding pack are 211 voltage taps, 34 temperature sensors, 34 helium flow monitors, 4 Hall probes, and 4 resistive surface heaters. The winding pack is contained within a structural case, a “trough and lid” style design composed of two Nitronic 50 forgings machined to shape and bolted together. The case reacts the large electromechanical stresses approaching 1 GPa during operation and serves as a pressure vessel that enables 20 bar supercritical helium flow that cools the winding pack and case. Two case extensions are attached to the case with unique high-pressure feedthroughs to provide winding pack access for current, cooling, and instrumentation, completing the magnet assembly.
- 22 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (2) , 1-15
Open AccessDesign, Fabrication, and Assembly of the SPARC Toroidal Field Model Coil
The SPARC Toroidal Field Model Coil (TFMC) is the first large-scale (∼3 m), high-field (∼20 T) superconducting fusion magnet based on Rare Earth Yttrium Barium Copper Oxide (REBCO). Weighing 10,058 kg and utilizing 270 km of REBCO, the TFMC is a non-insulated, stack-in-plate style superconducting magnet. It has three main components: (1) the winding pack; (2) the structural case; and (3) the case extensions, or plena. The winding pack is composed of sixteen single pancakes with two termination plates top and bottom. The pancakes are Nitronic 40 radial plates machined with spiral channels on one side for the REBCO tape stack and single-pass channels on the opposite side for supercritical helium coolant. After assembly, each pancake undergoes a vacuum-pressure impregnation solder process to provide good mechanical protection of the REBCO tape stack and efficient thermal and electrical connectivity within each pancake. The pancakes are bolted along the inner and outer perimeter to provide mechanical and thermal connectivity while inter-pancake joints provide low resistance current transfer between pancakes. The top and bottom termination plates facilitate electrical connection to a superconducting feeder system. Embedded throughout the winding pack are 211 voltage taps, 34 temperature sensors, 34 helium flow monitors, 4 Hall probes, and 4 resistive surface heaters. The winding pack is contained within a structural case, a “trough and lid” style design composed of two Nitronic 50 forgings machined to shape and bolted together. The case reacts the large electromechanical stresses approaching 1 GPa during operation and serves as a pressure vessel that enables 20 bar supercritical helium flow that cools the winding pack and case. Two case extensions are attached to the case with unique high-pressure feedthroughs to provide winding pack access for current, cooling, and instrumentation, completing the magnet assembly.
- Open Access
- 8 January 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (2) , 025006
Performance of demountable solder joints for no-insulation superconducting coils produced by vacuum pressure impregnation
No-insulation high temperature superconductor (HTS) stack coils show both increased thermal and electrical stability, and present a simplified geometry for the integration of demountable joints. Demountability is a desirable feature for many superconducting applications including fusion magnets, which motivate this research. In this work, a novel vacuum pressure impregnation (VPI) solder process was developed to couple superconducting paths via a low resistance, mechanically simply, demountable joint for a non-insulated coil design. The three low temperature solders considered were I n 52 S n 48 (mp = 118 ∘ C), I n 100 (mp = 156.6 ∘ C), and G a 100 (mp = 29.8 ∘ C), all with a lower melting point than the P b 37 S n 63 (mp = 183 ∘ C) used to solder the HTS tapes into the coil, thus allowing for the advantages of solder in the joint, yet facilitating demountability without disturbing the primary solder in the non-insulated coil stack. A multidisciplinary campaign was undertaken to design, build, test and identify the major challenges with these small-scale demountable solder joints. A multi probe voltage tap system was used to infer the effective resistances to exit a superconducting stack, cross the solder layer, and enter the second superconducting stack, at 77 K. The experimental resistivities show good agreement with a newly developed finite element model that breaks down domains to the level of individual layers of an HTS tape. When taking into account the thermal degradation that can occur to the HTS stacks during the VPI processes, the normalized joint resistances are found to be 528, 668, and 671 n Ω c m 2 for the I n 100 , I n 52 S n 48 and G a 100 solders, respectively. The benchmarked finite element model is used to predict normalized joint resistivities for fusion-relevant temperatures and magnetic fields using a 100 µm solder layer thickness, finding 38, 125, and 103 n Ω c m 2 for the respective solders; these results are competitive with the lowest resistance cable joints presented in the literature.
- 8 January 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (2) , 025006
Open AccessPerformance of demountable solder joints for no-insulation superconducting coils produced by vacuum pressure impregnation
No-insulation high temperature superconductor (HTS) stack coils show both increased thermal and electrical stability, and present a simplified geometry for the integration of demountable joints. Demountability is a desirable feature for many superconducting applications including fusion magnets, which motivate this research. In this work, a novel vacuum pressure impregnation (VPI) solder process was developed to couple superconducting paths via a low resistance, mechanically simply, demountable joint for a non-insulated coil design. The three low temperature solders considered were I n 52 S n 48 (mp = 118 ∘ C), I n 100 (mp = 156.6 ∘ C), and G a 100 (mp = 29.8 ∘ C), all with a lower melting point than the P b 37 S n 63 (mp = 183 ∘ C) used to solder the HTS tapes into the coil, thus allowing for the advantages of solder in the joint, yet facilitating demountability without disturbing the primary solder in the non-insulated coil stack. A multidisciplinary campaign was undertaken to design, build, test and identify the major challenges with these small-scale demountable solder joints. A multi probe voltage tap system was used to infer the effective resistances to exit a superconducting stack, cross the solder layer, and enter the second superconducting stack, at 77 K. The experimental resistivities show good agreement with a newly developed finite element model that breaks down domains to the level of individual layers of an HTS tape. When taking into account the thermal degradation that can occur to the HTS stacks during the VPI processes, the normalized joint resistances are found to be 528, 668, and 671 n Ω c m 2 for the I n 100 , I n 52 S n 48 and G a 100 solders, respectively. The benchmarked finite element model is used to predict normalized joint resistivities for fusion-relevant temperatures and magnetic fields using a 100 µm solder layer thickness, finding 38, 125, and 103 n Ω c m 2 for the respective solders; these results are competitive with the lowest resistance cable joints presented in the literature.
- Top Cited PapersOpen Access
- 14 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (2) , 1-18
Experimental Assessment and Model Validation of the SPARC Toroidal Field Model Coil
In this article, the SPARC Toroidal Field Model Coil (TFMC) experimental tests are described. The tests include detailed comparisons to a hierarchy of electromagnetic and structural models of the coil. The tests confirm the ability of the no-insulation no-twist (NINT) configuration to provide highly stable dc operations with peak magnetic field in excess of 20 T at the rare earth yttrium barium copper oxide (REBCO) tape stacks. The advantages of the modular TFMC approach are validated including the ability to test and probe the REBCO and structural response of the coil in stages, a strategy that will be applied to large-scale coil production for SPARC. The electromagnetic models show high fidelity agreement to the dc and charging coil performance in terms of current distribution, voltages, and heating. The transient response of the TFMC to open-circuit events is examined. The coil exhibits the positive features of the NINT design with very low induced voltages and a predictable redistribution of current and resulting volumetric heating. However, highly localized damage occurs during a programmed open circuit at operational conditions similar to those used in the SPARC tokamak, in agreement with calibrated electromagnetic models. This reveals the cause and remedy to the thermal instability that gives rise to the damage. Therefore, the conclusion of the tests is that the NINT TFMC is confirmed as meeting the programmatic requirements for SPARC and, more generally, for high-field tokamaks.
- 14 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (2) , 1-18
Top Cited PapersOpen AccessExperimental Assessment and Model Validation of the SPARC Toroidal Field Model Coil
In this article, the SPARC Toroidal Field Model Coil (TFMC) experimental tests are described. The tests include detailed comparisons to a hierarchy of electromagnetic and structural models of the coil. The tests confirm the ability of the no-insulation no-twist (NINT) configuration to provide highly stable dc operations with peak magnetic field in excess of 20 T at the rare earth yttrium barium copper oxide (REBCO) tape stacks. The advantages of the modular TFMC approach are validated including the ability to test and probe the REBCO and structural response of the coil in stages, a strategy that will be applied to large-scale coil production for SPARC. The electromagnetic models show high fidelity agreement to the dc and charging coil performance in terms of current distribution, voltages, and heating. The transient response of the TFMC to open-circuit events is examined. The coil exhibits the positive features of the NINT design with very low induced voltages and a predictable redistribution of current and resulting volumetric heating. However, highly localized damage occurs during a programmed open circuit at operational conditions similar to those used in the SPARC tokamak, in agreement with calibrated electromagnetic models. This reveals the cause and remedy to the thermal instability that gives rise to the damage. Therefore, the conclusion of the tests is that the NINT TFMC is confirmed as meeting the programmatic requirements for SPARC and, more generally, for high-field tokamaks.
- Open Access
- 8 November 2023
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 53 (1) , 418-431
The Effect of Joint Thickness on Intermetallic Growth in the In52Sn48(Liquid)/Cu(Solid) Diffusion Couple
Intermetallic growth can simultaneously enable low-resistance electrical pathways and determine the lifetime of a solder joint. Motivating this work is a demountable linear bilateral solder joint application, enabled via a vacuum pressure impregnation process. The effect of the initial solder joint thickness $$\delta _j = 25 - 125$$ $$\mu $$ m on intermetallic growth in this configuration is investigated for the $$\text{In}_{52}\text{Sn}_{48}$$ (liquid)/Cu(solid) diffusion couple for temperatures T = 393, 413 and 433 K, in the range just above the $$\text{In}_{52}\text{Sn}_{48}$$ melting temperature of 391 K. It was found that beyond a critical time $$\sim 1-15$$ min into the kinetic reaction, thicker solder joints had more intermetallic growth. There are two intermetallic phases identified in this temperature range: $$\text{Cu}_{6}\text{(In,Sn)}{_5}$$ closer to the Cu substrate, and $$\text{Cu(In,Sn)}_{2}$$ closer to the solder bulk. The intermetallic growth fits give temporal growth exponents between $$n = 0.25 - 0.29$$ , indicating that grain boundary diffusion rather than volume diffusion is the predominant growth mechanism. Growth in thicker joints is associated with higher temporal growth exponents; this is attributed to suppressed grain coarsening, as there is Cu dissolution from the intermetallic into the solder bulk in the early stages of the reaction, in more highly unsaturated environments. In addition, there is on average a decrease in the intermetallic phase activation energy with increasing joint thickness. In combination with the literature, the results suggest the linear bilateral joint geometry has a growth constraining effect, and the liquid solder phase state strongly affects the morphology and coarsening of grains, leading to the intermetallic growth trends observed.- 8 November 2023
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 53 (1) , 418-431
Open AccessThe Effect of Joint Thickness on Intermetallic Growth in the In52Sn48(Liquid)/Cu(Solid) Diffusion Couple
Intermetallic growth can simultaneously enable low-resistance electrical pathways and determine the lifetime of a solder joint. Motivating this work is a demountable linear bilateral solder joint application, enabled via a vacuum pressure impregnation process. The effect of the initial solder joint thickness $$\delta _j = 25 - 125$$ $$\mu $$ m on intermetallic growth in this configuration is investigated for the $$\text{In}_{52}\text{Sn}_{48}$$ (liquid)/Cu(solid) diffusion couple for temperatures T = 393, 413 and 433 K, in the range just above the $$\text{In}_{52}\text{Sn}_{48}$$ melting temperature of 391 K. It was found that beyond a critical time $$\sim 1-15$$ min into the kinetic reaction, thicker solder joints had more intermetallic growth. There are two intermetallic phases identified in this temperature range: $$\text{Cu}_{6}\text{(In,Sn)}{_5}$$ closer to the Cu substrate, and $$\text{Cu(In,Sn)}_{2}$$ closer to the solder bulk. The intermetallic growth fits give temporal growth exponents between $$n = 0.25 - 0.29$$ , indicating that grain boundary diffusion rather than volume diffusion is the predominant growth mechanism. Growth in thicker joints is associated with higher temporal growth exponents; this is attributed to suppressed grain coarsening, as there is Cu dissolution from the intermetallic into the solder bulk in the early stages of the reaction, in more highly unsaturated environments. In addition, there is on average a decrease in the intermetallic phase activation energy with increasing joint thickness. In combination with the literature, the results suggest the linear bilateral joint geometry has a growth constraining effect, and the liquid solder phase state strongly affects the morphology and coarsening of grains, leading to the intermetallic growth trends observed.