Ameur Belmouhoub
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ameur Belmouhoub has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Assia Abdelouahed
Department of Civil Engineering 20 Août1955 University of Skikda Skikda Algeria
2 shared publications Amira Afri
Department of Environmental Innovation and Eco‐Waste Management Division Environmental Research Center Annaba Algeria
1 shared publicationAmmar Noui
Department of Civil Engineering Mohamed Bachir El Ibrahimi University of Bordj Bou Arreridj Bordj Bou Arreridj Algeria
1 shared publication- Ammar Noui
Dept. of Civil Eng Mohamed El Bachir El Ibrahimi University of Bordj Bou Arreridj Algeria
1 shared publication - Oussama Kessal
Department of Civil Engineering Mohamed Bachir El Ibrahimi University of Bordj Bou Arreridj Bordj Bou Arreridj Algeria
1 shared publication - Ubagaram Johnson Alengaram
Centre for Innovative Construction Technology (CICT), Department of Civil Engineering, Faculty of Engineering Universiti Malaya Kuala Lumpur Malaysia
1 shared publication
Latest Publications
- 6 November 2026
- Published by Wiley in Structural Concrete
Microstructural properties of ordinary concrete mixed with rubber and plastic waste under aggressive environmental conditions: A full‐factorial design study
The aim of this study was to incorporate the waste plastic and rubber into concrete in order to manufacture concrete that is resistant to aggressive environments, using the factorial approach to assess the effect of different factors (rubber and plastic) on the selected responses. In this research, ordinary Portland cement and fine aggregate were partially replaced with rubber and plastic as a mass substitute in the proportions of 2% and 4% and the fine aggregate 2%, 4%, and 6%, respectively. The tests used for the fresh properties were workability and density, whereas the hardened properties were assessed using compressive strength, flexural strength, and weight loss, as well as micro‐structural analysis, XRD, and scanning electron microscopy, SEM. The results show a decrease in workability, density, compressive strength, flexural strength, and weight loss when increasing the percentage of plastic and rubber used. The workability decreases from 80 to 20 mm, and the density decreases from 2.38 to 2.20 kg/m 3 ; the compressive and flexural strengths, respectively, decreased by up to 38% and 20.5% at 28 days compared to the control concrete. Moreover, the weight loss decreases by up to 25% compared to the control concrete. In addition, SEM indicated that the voids are filled with the waste rubber and plastic and thus reduce the penetration of sulfuric acid into the concrete. This helps maintain the integrity and durability of concrete in the face of aggressive environments. The test findings were subjected to analyses of variance in order to determine the significance of the influence factors and their interactions on the chosen responses. The results show that the coefficient R 2 ranges between 0.89 and 0.99, which indicates a good correlation between the predicted and experimental modes.
- 6 November 2026
- Published by Wiley in Structural Concrete
Microstructural properties of ordinary concrete mixed with rubber and plastic waste under aggressive environmental conditions: A full‐factorial design study
The aim of this study was to incorporate the waste plastic and rubber into concrete in order to manufacture concrete that is resistant to aggressive environments, using the factorial approach to assess the effect of different factors (rubber and plastic) on the selected responses. In this research, ordinary Portland cement and fine aggregate were partially replaced with rubber and plastic as a mass substitute in the proportions of 2% and 4% and the fine aggregate 2%, 4%, and 6%, respectively. The tests used for the fresh properties were workability and density, whereas the hardened properties were assessed using compressive strength, flexural strength, and weight loss, as well as micro‐structural analysis, XRD, and scanning electron microscopy, SEM. The results show a decrease in workability, density, compressive strength, flexural strength, and weight loss when increasing the percentage of plastic and rubber used. The workability decreases from 80 to 20 mm, and the density decreases from 2.38 to 2.20 kg/m 3 ; the compressive and flexural strengths, respectively, decreased by up to 38% and 20.5% at 28 days compared to the control concrete. Moreover, the weight loss decreases by up to 25% compared to the control concrete. In addition, SEM indicated that the voids are filled with the waste rubber and plastic and thus reduce the penetration of sulfuric acid into the concrete. This helps maintain the integrity and durability of concrete in the face of aggressive environments. The test findings were subjected to analyses of variance in order to determine the significance of the influence factors and their interactions on the chosen responses. The results show that the coefficient R 2 ranges between 0.89 and 0.99, which indicates a good correlation between the predicted and experimental modes.
- Open Access
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Experimental and factorial design of the mechanical and physical properties of concrete containing waste rubber powder
The application of waste rubber in the Civil Engineering is considered one of the most effective solutions for managing this waste. Therefore, the aim of this study is to analyze the effect of rubber substituted in cement on the physical and mechanical properties of concrete using the general full factorial design method, and compare the laboratory results with the results of the JMP pilot test program, and find out if there is a match between the results. The rubber powder is used as a mass substitute in cement at rates of 0%, 2%, 4%, 6% and 8%. The fresh properties were evaluated through workability, air content, and fresh density tests, whereas the hardened properties were assessed using tests of compressive strength, flexural strength, and ultrasonic pulse velocity. These concretes have the workability from 8 to 14.5 cm, fresh density from 2.20 to 2.38 (g/cm3). The air content ranged from 1.2 to 1.9%. Furthermore, the compressive strength ranged from 22.85 to 43.97 MPa, while the flexural strength ranged from 4.86 to 7.03 MPa. In addition, ultrasonic velocity from 3831.42 to 4098.36 (m/s). Accordingly, it was concluded that the concrete with 2% of rubber represented significantly better compressive strength compared to the ordinary concrete. The numerical modeling is assessed to have an appropriate determined coefficient R2 close to 1 for the workability, fresh density, air content, compressive strength, flexural strength, and ultrasonic pulse velocity.
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessExperimental and factorial design of the mechanical and physical properties of concrete containing waste rubber powder
The application of waste rubber in the Civil Engineering is considered one of the most effective solutions for managing this waste. Therefore, the aim of this study is to analyze the effect of rubber substituted in cement on the physical and mechanical properties of concrete using the general full factorial design method, and compare the laboratory results with the results of the JMP pilot test program, and find out if there is a match between the results. The rubber powder is used as a mass substitute in cement at rates of 0%, 2%, 4%, 6% and 8%. The fresh properties were evaluated through workability, air content, and fresh density tests, whereas the hardened properties were assessed using tests of compressive strength, flexural strength, and ultrasonic pulse velocity. These concretes have the workability from 8 to 14.5 cm, fresh density from 2.20 to 2.38 (g/cm3). The air content ranged from 1.2 to 1.9%. Furthermore, the compressive strength ranged from 22.85 to 43.97 MPa, while the flexural strength ranged from 4.86 to 7.03 MPa. In addition, ultrasonic velocity from 3831.42 to 4098.36 (m/s). Accordingly, it was concluded that the concrete with 2% of rubber represented significantly better compressive strength compared to the ordinary concrete. The numerical modeling is assessed to have an appropriate determined coefficient R2 close to 1 for the workability, fresh density, air content, compressive strength, flexural strength, and ultrasonic pulse velocity.