Assia Abdelouahed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Assia Abdelouahed has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Ameur Belmouhoub
Department of Civil Engineering 20 Août1955 University of Skikda Skikda Algeria
2 shared publications Houria Hebhoub
2 shared publications- Houria Hebhoub
Civil Engineering Department, Faculty of Sciences and Technologies, University of 20 August 1955, Skikda 21000, Algeria
2 shared publications Leila Kherraf
University of 20 August 1955, LMGHU Laboratory, B.P.26 El-Hadaiek road, Skikda, Algeria
2 shared publications- Mouloud Belachia
Materials, Geotechnics, Habitat and Urban Laboratory, University of 20 Août 1955, Skikda, Algeria
2 shared publications - Wassila Boughamssa
Department of Civil Engineering 20 Août1955 University of Skikda Skikda Algeria
2 shared publications
Latest Publications
- 6 November 2026
- Published by Wiley in Structural Concrete
Microstructural properties of ordinary concrete mixed with rubber and plastic waste under aggressive environmental conditions: A full‐factorial design study
The aim of this study was to incorporate the waste plastic and rubber into concrete in order to manufacture concrete that is resistant to aggressive environments, using the factorial approach to assess the effect of different factors (rubber and plastic) on the selected responses. In this research, ordinary Portland cement and fine aggregate were partially replaced with rubber and plastic as a mass substitute in the proportions of 2% and 4% and the fine aggregate 2%, 4%, and 6%, respectively. The tests used for the fresh properties were workability and density, whereas the hardened properties were assessed using compressive strength, flexural strength, and weight loss, as well as micro‐structural analysis, XRD, and scanning electron microscopy, SEM. The results show a decrease in workability, density, compressive strength, flexural strength, and weight loss when increasing the percentage of plastic and rubber used. The workability decreases from 80 to 20 mm, and the density decreases from 2.38 to 2.20 kg/m 3 ; the compressive and flexural strengths, respectively, decreased by up to 38% and 20.5% at 28 days compared to the control concrete. Moreover, the weight loss decreases by up to 25% compared to the control concrete. In addition, SEM indicated that the voids are filled with the waste rubber and plastic and thus reduce the penetration of sulfuric acid into the concrete. This helps maintain the integrity and durability of concrete in the face of aggressive environments. The test findings were subjected to analyses of variance in order to determine the significance of the influence factors and their interactions on the chosen responses. The results show that the coefficient R 2 ranges between 0.89 and 0.99, which indicates a good correlation between the predicted and experimental modes.
- 6 November 2026
- Published by Wiley in Structural Concrete
Microstructural properties of ordinary concrete mixed with rubber and plastic waste under aggressive environmental conditions: A full‐factorial design study
The aim of this study was to incorporate the waste plastic and rubber into concrete in order to manufacture concrete that is resistant to aggressive environments, using the factorial approach to assess the effect of different factors (rubber and plastic) on the selected responses. In this research, ordinary Portland cement and fine aggregate were partially replaced with rubber and plastic as a mass substitute in the proportions of 2% and 4% and the fine aggregate 2%, 4%, and 6%, respectively. The tests used for the fresh properties were workability and density, whereas the hardened properties were assessed using compressive strength, flexural strength, and weight loss, as well as micro‐structural analysis, XRD, and scanning electron microscopy, SEM. The results show a decrease in workability, density, compressive strength, flexural strength, and weight loss when increasing the percentage of plastic and rubber used. The workability decreases from 80 to 20 mm, and the density decreases from 2.38 to 2.20 kg/m 3 ; the compressive and flexural strengths, respectively, decreased by up to 38% and 20.5% at 28 days compared to the control concrete. Moreover, the weight loss decreases by up to 25% compared to the control concrete. In addition, SEM indicated that the voids are filled with the waste rubber and plastic and thus reduce the penetration of sulfuric acid into the concrete. This helps maintain the integrity and durability of concrete in the face of aggressive environments. The test findings were subjected to analyses of variance in order to determine the significance of the influence factors and their interactions on the chosen responses. The results show that the coefficient R 2 ranges between 0.89 and 0.99, which indicates a good correlation between the predicted and experimental modes.
- 17 February 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 86
Mechanical, durability and microstructure properties of eco-friendly sand concrete incorporating cane ash
- 17 February 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 86
Mechanical, durability and microstructure properties of eco-friendly sand concrete incorporating cane ash
- Open Access
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Experimental and factorial design of the mechanical and physical properties of concrete containing waste rubber powder
The application of waste rubber in the Civil Engineering is considered one of the most effective solutions for managing this waste. Therefore, the aim of this study is to analyze the effect of rubber substituted in cement on the physical and mechanical properties of concrete using the general full factorial design method, and compare the laboratory results with the results of the JMP pilot test program, and find out if there is a match between the results. The rubber powder is used as a mass substitute in cement at rates of 0%, 2%, 4%, 6% and 8%. The fresh properties were evaluated through workability, air content, and fresh density tests, whereas the hardened properties were assessed using tests of compressive strength, flexural strength, and ultrasonic pulse velocity. These concretes have the workability from 8 to 14.5 cm, fresh density from 2.20 to 2.38 (g/cm3). The air content ranged from 1.2 to 1.9%. Furthermore, the compressive strength ranged from 22.85 to 43.97 MPa, while the flexural strength ranged from 4.86 to 7.03 MPa. In addition, ultrasonic velocity from 3831.42 to 4098.36 (m/s). Accordingly, it was concluded that the concrete with 2% of rubber represented significantly better compressive strength compared to the ordinary concrete. The numerical modeling is assessed to have an appropriate determined coefficient R2 close to 1 for the workability, fresh density, air content, compressive strength, flexural strength, and ultrasonic pulse velocity.
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessExperimental and factorial design of the mechanical and physical properties of concrete containing waste rubber powder
The application of waste rubber in the Civil Engineering is considered one of the most effective solutions for managing this waste. Therefore, the aim of this study is to analyze the effect of rubber substituted in cement on the physical and mechanical properties of concrete using the general full factorial design method, and compare the laboratory results with the results of the JMP pilot test program, and find out if there is a match between the results. The rubber powder is used as a mass substitute in cement at rates of 0%, 2%, 4%, 6% and 8%. The fresh properties were evaluated through workability, air content, and fresh density tests, whereas the hardened properties were assessed using tests of compressive strength, flexural strength, and ultrasonic pulse velocity. These concretes have the workability from 8 to 14.5 cm, fresh density from 2.20 to 2.38 (g/cm3). The air content ranged from 1.2 to 1.9%. Furthermore, the compressive strength ranged from 22.85 to 43.97 MPa, while the flexural strength ranged from 4.86 to 7.03 MPa. In addition, ultrasonic velocity from 3831.42 to 4098.36 (m/s). Accordingly, it was concluded that the concrete with 2% of rubber represented significantly better compressive strength compared to the ordinary concrete. The numerical modeling is assessed to have an appropriate determined coefficient R2 close to 1 for the workability, fresh density, air content, compressive strength, flexural strength, and ultrasonic pulse velocity.
- Open Access
- 30 October 2022
- Published by Czech Technical University in Prague - Central Library in Stavební obzor - Civil Engineering Journal
- Vol. 31 (3) , 415-426
THE COMPARATIVE STUDY OF THE PERFORMANCE OF CONCRETE MADE FROM RECYCLED SAND
The main objective of this study of research is to initiate and develop a comparative study of fresh and hardened properties of concretes made from recycled sand from three types of waste: marble waste, tiling waste and cinder block waste. And this, in the intention of contributing to the world effort relating to the preserve of natural aggregate resources and limit landfill to the ultimate waste thresholds. To do this, in the composition of a current concrete with a water / cement ratio equal to 0.55, an equivalent volume of sand from the three wastes respectively replaced a volume of 15% of the ordinary sand. The properties in the fresh state: workability, air content and density and in the hardened state: compressive strength, Flexural tensile strength, compressive strength determined with non-destructive tests, water absorption by immersion, absorption by capillarity and chloride penetration of the various concretes produced are analyzed, and compared to those of the control concrete. The results obtained show that the concretes containing the waste sands have acceptable characteristics. However, tiling waste sand performs better than the other two recycled sands.
- 30 October 2022
- Published by Czech Technical University in Prague - Central Library in Stavební obzor - Civil Engineering Journal
- Vol. 31 (3) , 415-426
Open AccessTHE COMPARATIVE STUDY OF THE PERFORMANCE OF CONCRETE MADE FROM RECYCLED SAND
The main objective of this study of research is to initiate and develop a comparative study of fresh and hardened properties of concretes made from recycled sand from three types of waste: marble waste, tiling waste and cinder block waste. And this, in the intention of contributing to the world effort relating to the preserve of natural aggregate resources and limit landfill to the ultimate waste thresholds. To do this, in the composition of a current concrete with a water / cement ratio equal to 0.55, an equivalent volume of sand from the three wastes respectively replaced a volume of 15% of the ordinary sand. The properties in the fresh state: workability, air content and density and in the hardened state: compressive strength, Flexural tensile strength, compressive strength determined with non-destructive tests, water absorption by immersion, absorption by capillarity and chloride penetration of the various concretes produced are analyzed, and compared to those of the control concrete. The results obtained show that the concretes containing the waste sands have acceptable characteristics. However, tiling waste sand performs better than the other two recycled sands.
- 1 January 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 45
Comparative study on the performance of sand-based mortars from marble, floor tile and cinder block waste
- 1 January 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 45
Comparative study on the performance of sand-based mortars from marble, floor tile and cinder block waste
- Open Access
- 1 December 2019
- Published by University of Zielona Góra, Poland in Civil and Environmental Engineering Reports
- Vol. 29 (4) , 41-61
Valorization of Waste in Sand Concrete Based on Plant Fibres
The introduction of treated plant fibres into sand concretes leads to a reduction in density, improved ductility and thermal conductivity, and makes sand concrete an environmentally friendly and ecological material. The recovery of waste in this type of material allows the production of new ecological and sustainable materials used either in the new construction or in the rehabilitation of old buildings. In this context, a comparative study was based on the valorisation of marble and ceramic waste as sand in sand concrete made from straw fibres. To carry out this study, we introduced these wastes at substitution rates of 10% and 20%, separated and mixed, and studied the development of the properties of these concretes (density, workability, air content, compressive strength and bending tensile strength) and their behaviour with respect to durability (capillary and immersion absorption and chloride penetration). The study shows that the recovery of this waste as sand in sand concrete based on straw fibres gives satisfactory results. The chemical resistance, thermal conductivity and microstructure are under study, the results of which will be the subject of another publication.
- 1 December 2019
- Published by University of Zielona Góra, Poland in Civil and Environmental Engineering Reports
- Vol. 29 (4) , 41-61
Open AccessValorization of Waste in Sand Concrete Based on Plant Fibres
The introduction of treated plant fibres into sand concretes leads to a reduction in density, improved ductility and thermal conductivity, and makes sand concrete an environmentally friendly and ecological material. The recovery of waste in this type of material allows the production of new ecological and sustainable materials used either in the new construction or in the rehabilitation of old buildings. In this context, a comparative study was based on the valorisation of marble and ceramic waste as sand in sand concrete made from straw fibres. To carry out this study, we introduced these wastes at substitution rates of 10% and 20%, separated and mixed, and studied the development of the properties of these concretes (density, workability, air content, compressive strength and bending tensile strength) and their behaviour with respect to durability (capillary and immersion absorption and chloride penetration). The study shows that the recovery of this waste as sand in sand concrete based on straw fibres gives satisfactory results. The chemical resistance, thermal conductivity and microstructure are under study, the results of which will be the subject of another publication.
- 16 May 2016
- Published by Taylor & Francis in European Journal of Environmental and Civil Engineering
- Vol. 22 (2) , 212-225
Effect of SCMs on mechanical, chemical and microstructural properties of SRC in acidic medium
This paper studies the durability of the mortar base of sulphate-resistant cement (SRC) with supplementary cementitious materials (SCMs) as substitutes for SRC to reduce its cost and enhance its durability to acids. Three SCMs (granulated blast-furnace slag, natural tuff and natural pozzolan) are used with weight ratios of 5, 10, 15 and 20%. A compressive strength test, X-ray diffraction and weight loss test were carried out through the conducted experiments and the results were compared with values for reference with SRC. The different results show that the compressive strength decreases with increasing tuff and slag contents, while the weight loss decreases with increasing tuff content. Mortars with a pozzolan content of 10% give similar results to SRC.
- 16 May 2016
- Published by Taylor & Francis in European Journal of Environmental and Civil Engineering
- Vol. 22 (2) , 212-225
Effect of SCMs on mechanical, chemical and microstructural properties of SRC in acidic medium
This paper studies the durability of the mortar base of sulphate-resistant cement (SRC) with supplementary cementitious materials (SCMs) as substitutes for SRC to reduce its cost and enhance its durability to acids. Three SCMs (granulated blast-furnace slag, natural tuff and natural pozzolan) are used with weight ratios of 5, 10, 15 and 20%. A compressive strength test, X-ray diffraction and weight loss test were carried out through the conducted experiments and the results were compared with values for reference with SRC. The different results show that the compressive strength decreases with increasing tuff and slag contents, while the weight loss decreases with increasing tuff content. Mortars with a pozzolan content of 10% give similar results to SRC.