Carina Ludwig
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Carina Ludwig has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Manfred Kohl
Institute of Microstructure Technology, Karlsruhe Institute of Technology, Karlsruhe, Germany
2 shared publications Jan Leutner
Department of Microsystems Engineering (IMTEK), University of Freiburg, Georges-Köhler-Allee 103, 79110 Freiburg, Germany
1 shared publicationJürgen Rühe
Department of Microsystems Engineering (IMTEK), University of Freiburg, Georges-Köhler-Allee 103, 79110 Freiburg, Germany
1 shared publication- Oswald Prucker
Department of Microsystems Engineering (IMTEK) Laboratory for Chemistry & Physics of Interfaces Albert‐Ludwigs‐Universität Freiburg Freiburg Germany
1 shared publication
Latest Publications
- Open Access
- 22 October 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (16)
Bistability-enhanced elastocaloric cooling device based on a natural rubber foil
A novel solid-state elastocaloric cooling device is presented, making use of a bistable actuation mechanism for loading of a natural rubber (NR) foil refrigerant. The thicknesses of the foil refrigerants are 290 and 650 μm in an initial undeformed state, while their lateral size is 9 × 26.5 mm2. Owing to the large surface-to-volume ratio of the NR foils, heat transfer to the heat sink and source is accomplished by a solid–solid mechanical contact. The loading mechanism consists of a rotating lever arm providing for stable positions at contact to the heat sink and source, which allows for significant power saving during elastocaloric cycling. In addition, the negative biasing associated with bistability favors good thermal contact at the end positions, which improves heat transfer resulting in a maximum temperature span ΔTdevice of 4.2 K in the strain range of 300%–700% under adiabatic conditions. The coefficient of performance of the device COPdevice reaches values up to 5.7 for foil refrigerants of 290 μm thickness. The maximum cooling power is 214 mW corresponding to a specific cooling power of 3.4 Wg−1.
- 22 October 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (16)
Open AccessBistability-enhanced elastocaloric cooling device based on a natural rubber foil
A novel solid-state elastocaloric cooling device is presented, making use of a bistable actuation mechanism for loading of a natural rubber (NR) foil refrigerant. The thicknesses of the foil refrigerants are 290 and 650 μm in an initial undeformed state, while their lateral size is 9 × 26.5 mm2. Owing to the large surface-to-volume ratio of the NR foils, heat transfer to the heat sink and source is accomplished by a solid–solid mechanical contact. The loading mechanism consists of a rotating lever arm providing for stable positions at contact to the heat sink and source, which allows for significant power saving during elastocaloric cycling. In addition, the negative biasing associated with bistability favors good thermal contact at the end positions, which improves heat transfer resulting in a maximum temperature span ΔTdevice of 4.2 K in the strain range of 300%–700% under adiabatic conditions. The coefficient of performance of the device COPdevice reaches values up to 5.7 for foil refrigerants of 290 μm thickness. The maximum cooling power is 214 mW corresponding to a specific cooling power of 3.4 Wg−1.
- Open Access
- 28 November 2023
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 6 (1) , 015009
Miniature-scale elastocaloric cooling by rubber-based foils
We report on the design and characterization of a demonstrator device for miniature-scale elastocaloric (eC) cooling using a series of natural rubber (NR) foil specimens of 9 × 26.5 mm2 lateral size and thicknesses in the range of 290–900 μm. NR has the potential to meet the various challenges associated with eC cooling, as it exhibits a large adiabatic temperature change in the order of 20 K and high fatigue resistance under dynamic load, while loading forces are low. Owing to the large surface-to-volume ratio of rubber-based foils, heat transfer to heat sink and source elements is accomplished by mechanical contact enabling compact designs. Two actuators are implemented to control the performance in loading direction independent from the performance of mechanical contacting. The study of operation parameters is complemented by lumped-element modeling to understand the cycle frequency-dependent dynamics of heat transfer and resulting cooling capacity. The single-stage device operates in the strain range of 300%–700% and exhibits a temperature span up to 4.1 K, while the specific cooling power reaches 1.1 Wg−1 and the absolute cooling power 123 mW. The performance metrics show a pronounced dependence on foil thickness and heat transfer coefficient indicating a path toward future device optimization.
- 28 November 2023
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 6 (1) , 015009
Open AccessMiniature-scale elastocaloric cooling by rubber-based foils
We report on the design and characterization of a demonstrator device for miniature-scale elastocaloric (eC) cooling using a series of natural rubber (NR) foil specimens of 9 × 26.5 mm2 lateral size and thicknesses in the range of 290–900 μm. NR has the potential to meet the various challenges associated with eC cooling, as it exhibits a large adiabatic temperature change in the order of 20 K and high fatigue resistance under dynamic load, while loading forces are low. Owing to the large surface-to-volume ratio of rubber-based foils, heat transfer to heat sink and source elements is accomplished by mechanical contact enabling compact designs. Two actuators are implemented to control the performance in loading direction independent from the performance of mechanical contacting. The study of operation parameters is complemented by lumped-element modeling to understand the cycle frequency-dependent dynamics of heat transfer and resulting cooling capacity. The single-stage device operates in the strain range of 300%–700% and exhibits a temperature span up to 4.1 K, while the specific cooling power reaches 1.1 Wg−1 and the absolute cooling power 123 mW. The performance metrics show a pronounced dependence on foil thickness and heat transfer coefficient indicating a path toward future device optimization.