Oswald Prucker
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Oswald Prucker has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Jürgen Rühe
Department of Microsystems Engineering (IMTEK) Laboratory for Chemistry & Physics of Interfaces (CPI) Albert‐Ludwigs‐Universität Freiburg Georges‐Köhler‐Allee 103 79110 Freiburg Germany
4 shared publications- Jürgen Rühe
Department of Microsystems Engineering (IMTEK), University of Freiburg, Georges-Köhler-Allee 103, 79110 Freiburg, Germany
2 shared publications Anja Wallrath
Cardiothoracic and Vascular Surgery, University‐Hospital Mainz, Germany
1 shared publicationBernd Berchthold
IMTEK, Albert‐Ludwigs‐University Freiburg, Germany
1 shared publicationBung‐Jun Chang
IMTEK, Albert‐Ludwigs‐University Freiburg, Germany
1 shared publication- Carina Ludwig
Institute of Microstructure Technology (IMT), Karlsruhe Institute of Technology (KIT) , P.O. Box 3640, 76021 Karlsruhe
1 shared publication
Latest Publications
- Open Access
- 9 September 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (21)
Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring
Monitoring forest ecosystems requires outdoor sensors capable of long‐term operation throughout an entire growing season. They must remain protected against dust and pollen without any human intervention. This article presents a novel self‐cleaning and antibiofouling surface for cuvettes connected to leaf‐attached gas sensors using a combination of nanoparticles and C─H insertion crosslinking (CHic). Specifically, a solution containing trimethylsilyl‐functionalized silica nanoparticles (NPs) and a perfluoroacrylate (PFA) copolymer with integrated photoreactive benzophenone (BP) moieties is spray‐coated onto the substrate surfaces. Upon UV irradiation, the dormant BP moieties become activated and react with nearby C─H groups via C─H insertion leading to crosslinking of the coating layer. Simultaneously, reactions occur with C─H groups present in the polymer substrate, leading to covalent attachment of the network to the cuvette surface, and between the polymer network and the NPs, so that all reactions are performed within a single process step. Covalent bonds established by the CHic process provide strong adhesion and enhanced stability of the generated superhydrophobic coating to the cuvette surface. Finally, the cuvettes were attached to tree leaves and exposed to outdoor forest environments, where they exhibited efficient self‐cleaning behavior. The coatings demonstrated robust antisoiling and antibiofouling performance over a whole vegetation period in the forest.
- 9 September 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (21)
Open AccessSelf‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring
Monitoring forest ecosystems requires outdoor sensors capable of long‐term operation throughout an entire growing season. They must remain protected against dust and pollen without any human intervention. This article presents a novel self‐cleaning and antibiofouling surface for cuvettes connected to leaf‐attached gas sensors using a combination of nanoparticles and C─H insertion crosslinking (CHic). Specifically, a solution containing trimethylsilyl‐functionalized silica nanoparticles (NPs) and a perfluoroacrylate (PFA) copolymer with integrated photoreactive benzophenone (BP) moieties is spray‐coated onto the substrate surfaces. Upon UV irradiation, the dormant BP moieties become activated and react with nearby C─H groups via C─H insertion leading to crosslinking of the coating layer. Simultaneously, reactions occur with C─H groups present in the polymer substrate, leading to covalent attachment of the network to the cuvette surface, and between the polymer network and the NPs, so that all reactions are performed within a single process step. Covalent bonds established by the CHic process provide strong adhesion and enhanced stability of the generated superhydrophobic coating to the cuvette surface. Finally, the cuvettes were attached to tree leaves and exposed to outdoor forest environments, where they exhibited efficient self‐cleaning behavior. The coatings demonstrated robust antisoiling and antibiofouling performance over a whole vegetation period in the forest.
- Open Access
- 9 February 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 35 (24)
Superlubricious Surfaces Through Surface Attached Hydrogels Obtained by C,H‐insertion Crosslinking
The friction behavior of surfaces is investigated which are coated with surface‐attached hydrogel layers inspired by the structure of natural synovial joints. Photoinduced C,H insertion chemistry is used to form polymer networks from hydrogel precursor polymers and simultaneously link them to both sliding partners. As the crosslinking is performed in the dry state and all polymer chains are covalently bound to the surface, the hydrogel layers can only swell in one direction leading to strong chain stretching. This confinement leads to surfaces with ultralow adhesion and strongly reduces friction. The incorporation of charges and the addition of shear‐thinning polymers to the water phase allows for the generation of friction systems having coefficients of friction of µ = 0.002–0.001, thus reaching superlubricity and even surpassing the values reported for the properties of the natural model.
- 9 February 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 35 (24)
Open AccessSuperlubricious Surfaces Through Surface Attached Hydrogels Obtained by C,H‐insertion Crosslinking
The friction behavior of surfaces is investigated which are coated with surface‐attached hydrogel layers inspired by the structure of natural synovial joints. Photoinduced C,H insertion chemistry is used to form polymer networks from hydrogel precursor polymers and simultaneously link them to both sliding partners. As the crosslinking is performed in the dry state and all polymer chains are covalently bound to the surface, the hydrogel layers can only swell in one direction leading to strong chain stretching. This confinement leads to surfaces with ultralow adhesion and strongly reduces friction. The incorporation of charges and the addition of shear‐thinning polymers to the water phase allows for the generation of friction systems having coefficients of friction of µ = 0.002–0.001, thus reaching superlubricity and even surpassing the values reported for the properties of the natural model.
Advancing Glucose Sensing Through Auto‐Fluorescent Polymer Brushes: From Surface Design to Nano‐Arrays
Designing smart (bio)interfaces with the capability to sense and react to changes in local environments offers intriguing possibilities for new surface‐based sensing devices and technologies. Polymer brushes make ideal materials to design such adaptive and responsive interfaces given their large variety of functional and structural possibilities as well as their outstanding abilities to respond to physical, chemical, and biological stimuli. Herein, a practical sensory interface for glucose detection based on auto‐fluorescent polymer brushes decorated with phenylboronic acid (PBA) receptors is presented. The glucose‐responsive luminescent surfaces, which are capable of translating conformational transitions triggered by pH variations and binding events into fluorescent readouts without the need for fluorescent dyes, are grown from both nanopatterned and non‐patterned substrates. Two‐photon laser scanning confocal microscopy and atomic force microscopy (AFM) analyses reveal the relationship between the brush conformation and glucose concentration and confirm that the phenylboronic acid functionalized brushes can bind glucose over a range of physiologically relevant concentrations in a reversible manner. The combination of auto‐fluorescent polymer brushes with synthetic receptors presents a promising avenue for designing innovative and robust sensing systems, which are essential for various biomedical applications, among other uses.
Advancing Glucose Sensing Through Auto‐Fluorescent Polymer Brushes: From Surface Design to Nano‐Arrays
Designing smart (bio)interfaces with the capability to sense and react to changes in local environments offers intriguing possibilities for new surface‐based sensing devices and technologies. Polymer brushes make ideal materials to design such adaptive and responsive interfaces given their large variety of functional and structural possibilities as well as their outstanding abilities to respond to physical, chemical, and biological stimuli. Herein, a practical sensory interface for glucose detection based on auto‐fluorescent polymer brushes decorated with phenylboronic acid (PBA) receptors is presented. The glucose‐responsive luminescent surfaces, which are capable of translating conformational transitions triggered by pH variations and binding events into fluorescent readouts without the need for fluorescent dyes, are grown from both nanopatterned and non‐patterned substrates. Two‐photon laser scanning confocal microscopy and atomic force microscopy (AFM) analyses reveal the relationship between the brush conformation and glucose concentration and confirm that the phenylboronic acid functionalized brushes can bind glucose over a range of physiologically relevant concentrations in a reversible manner. The combination of auto‐fluorescent polymer brushes with synthetic receptors presents a promising avenue for designing innovative and robust sensing systems, which are essential for various biomedical applications, among other uses.
- Open Access
- 28 November 2023
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 6 (1) , 015009
Miniature-scale elastocaloric cooling by rubber-based foils
We report on the design and characterization of a demonstrator device for miniature-scale elastocaloric (eC) cooling using a series of natural rubber (NR) foil specimens of 9 × 26.5 mm2 lateral size and thicknesses in the range of 290–900 μm. NR has the potential to meet the various challenges associated with eC cooling, as it exhibits a large adiabatic temperature change in the order of 20 K and high fatigue resistance under dynamic load, while loading forces are low. Owing to the large surface-to-volume ratio of rubber-based foils, heat transfer to heat sink and source elements is accomplished by mechanical contact enabling compact designs. Two actuators are implemented to control the performance in loading direction independent from the performance of mechanical contacting. The study of operation parameters is complemented by lumped-element modeling to understand the cycle frequency-dependent dynamics of heat transfer and resulting cooling capacity. The single-stage device operates in the strain range of 300%–700% and exhibits a temperature span up to 4.1 K, while the specific cooling power reaches 1.1 Wg−1 and the absolute cooling power 123 mW. The performance metrics show a pronounced dependence on foil thickness and heat transfer coefficient indicating a path toward future device optimization.
- 28 November 2023
- Published by IOP Publishing in Journal of Physics: Energy
- Vol. 6 (1) , 015009
Open AccessMiniature-scale elastocaloric cooling by rubber-based foils
We report on the design and characterization of a demonstrator device for miniature-scale elastocaloric (eC) cooling using a series of natural rubber (NR) foil specimens of 9 × 26.5 mm2 lateral size and thicknesses in the range of 290–900 μm. NR has the potential to meet the various challenges associated with eC cooling, as it exhibits a large adiabatic temperature change in the order of 20 K and high fatigue resistance under dynamic load, while loading forces are low. Owing to the large surface-to-volume ratio of rubber-based foils, heat transfer to heat sink and source elements is accomplished by mechanical contact enabling compact designs. Two actuators are implemented to control the performance in loading direction independent from the performance of mechanical contacting. The study of operation parameters is complemented by lumped-element modeling to understand the cycle frequency-dependent dynamics of heat transfer and resulting cooling capacity. The single-stage device operates in the strain range of 300%–700% and exhibits a temperature span up to 4.1 K, while the specific cooling power reaches 1.1 Wg−1 and the absolute cooling power 123 mW. The performance metrics show a pronounced dependence on foil thickness and heat transfer coefficient indicating a path toward future device optimization.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19483546,p. 561-564
Fabrication and implantation of hydrogel coated, flexible polyimide electrodes
Within this study, flexible, polyimide based shaft electrodes were fabricated and dip-coated with a PDMAA-co-SSAz solution that formed a thin hydrogel layer on the electrode shanks. This layer stiffened the electrode for insertion when thoroughly dried. The electrodes were successfully implanted into a brain model and into real brain tissue of rodents. The insertion forces during in vitro and in vivo implantation were recorded and compared. Pre-pricking of an insertion channel didn't simplify the insertion in vitro in all cases. The final insertion forces were in vivo (15 - 58 mN) slightly higher than in vitro (12 - 20 mN). Electrochemical impedance spectra were recorded in vivo up to twelve weeks post implantation, measuring the impedance between two electrode sites through the hydrogel. Three types of impedance spectra were observed during the implantation period: mainly resistive spectra, mainly capacitive spectra and spectra showing resistive and capacitive components. One week after implantation, the amount of spectra with resistive-capacitive components was 90 % and decreased to 50 % in week twelve, while the amount of mainly resistive spectra increased from initially 2 % to 38 %. The amount of mainly capacitive spectra changed from 8 % in week one to 12 % in week twelve.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19483546,p. 561-564
Fabrication and implantation of hydrogel coated, flexible polyimide electrodes
Within this study, flexible, polyimide based shaft electrodes were fabricated and dip-coated with a PDMAA-co-SSAz solution that formed a thin hydrogel layer on the electrode shanks. This layer stiffened the electrode for insertion when thoroughly dried. The electrodes were successfully implanted into a brain model and into real brain tissue of rodents. The insertion forces during in vitro and in vivo implantation were recorded and compared. Pre-pricking of an insertion channel didn't simplify the insertion in vitro in all cases. The final insertion forces were in vivo (15 - 58 mN) slightly higher than in vitro (12 - 20 mN). Electrochemical impedance spectra were recorded in vivo up to twelve weeks post implantation, measuring the impedance between two electrode sites through the hydrogel. Three types of impedance spectra were observed during the implantation period: mainly resistive spectra, mainly capacitive spectra and spectra showing resistive and capacitive components. One week after implantation, the amount of spectra with resistive-capacitive components was 90 % and decreased to 50 % in week twelve, while the amount of mainly resistive spectra increased from initially 2 % to 38 %. The amount of mainly capacitive spectra changed from 8 % in week one to 12 % in week twelve.
- 1 November 2004
- Published by SAGE Publications in Bio-Medical Materials and Engineering
- Vol. 14 (4) , 419-425
Ultrathin polymer monolayers for promotion of cell growth on bioprosthetic materials – Evolution of a new concept to improve long term performance of biologic heart vales
Reoperation of aldehyde tanned bioprotheses due to calcific degeneration remains their major drawback. Based on experiments studying mechanisms and factors that influence the time phase, extent and progression of calcification and evaluating the efficiency of anticalcification treatments and the effects of surface seeding with vital cells a new concept to avoid calcification emerged: masking aldehyde‐residues with a covalently bound polymer that supports surface cell seeding. Different covalently bound polymers were tested for their suitability to grow cells. Dense cell growth was achieved on some polymers but without correlation to physico‐chemical properties. Ultrathin coating of biological materials appears a promising approach to achieve lining with vital cells.
- 1 November 2004
- Published by SAGE Publications in Bio-Medical Materials and Engineering
- Vol. 14 (4) , 419-425
Ultrathin polymer monolayers for promotion of cell growth on bioprosthetic materials – Evolution of a new concept to improve long term performance of biologic heart vales
Reoperation of aldehyde tanned bioprotheses due to calcific degeneration remains their major drawback. Based on experiments studying mechanisms and factors that influence the time phase, extent and progression of calcification and evaluating the efficiency of anticalcification treatments and the effects of surface seeding with vital cells a new concept to avoid calcification emerged: masking aldehyde‐residues with a covalently bound polymer that supports surface cell seeding. Different covalently bound polymers were tested for their suitability to grow cells. Dense cell growth was achieved on some polymers but without correlation to physico‐chemical properties. Ultrathin coating of biological materials appears a promising approach to achieve lining with vital cells.