OGOziel Gómez-Casas

Oziel Gómez-Casas

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oziel Gómez-Casas has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Data-Driven Kinematic Model for the End-Effector Pose Control of a Manipulator Robot

    by Josué Goméz-Casas, Carlos A. Toro-Arcila, Nelly Abigaíl Rodríguez-Rosales, Jonathan Obregón-Flores, Daniela E. Ortíz-Ramos, Jesús Fernando Martínez-Villafañe, Oziel Gómez-Casas

    This paper presents a data-driven kinematic model for the end-effector pose control applied to a variety of manipulator robots, focusing on the entire end-effector’s pose (position and orientation). The measured signals of the full pose and their computed derivatives, along with a linear combination of an estimated Jacobian matrix and a vector of joint velocities, generate a model estimation error. The Jacobian matrix is estimated using the Pseudo Jacobian Matrix (PJM) algorithm, which requires tuning only the step and weight parameters that scale the convergence of the model estimation error. The proposed control law is derived in two stages: the first one is part of an objective function minimization, and the second one is a constraint in a quasi-Lagrangian function. The control design parameters guarantee the control error convergence in a closed-loop configuration with adaptive behavior in terms of the dynamics of the estimated Jacobian matrix. The novelty of the approach lies in its ability to achieve superior tracking performance across different manipulator robots, validated through simulations. Quantitative results show that, compared to a classical inverse-kinematics approach, the proposed method achieves rapid convergence of performance indices (e.g., Root Mean Square Error (RMSE) reduced to near-zero in two cycles vs. a steady-state RMSE of 20 in the classical approach). Additionally, the proposed method minimizes joint drift, maintaining an RMSE of approximately 0.3 compared to 1.5 under the classical scheme. The control was validated by means of simulations featuring an UR5e manipulator with six Degrees of Freedom (DOF), a KUKA Youbot with eight DOF, and a KUKA Youbot Dual with thirteen DOF. The stability analysis of the closed-loop controller is demonstrated by means of the Lyapunov stability conditions.


  • Open Access

    Interelectrode Distance Analysis in the Water Defluoridation by Electrocoagulation Reactor

    by Jesús Fernando Martínez-Villafañe, Juan Carlos Ortiz-Cuellar, Jesús Salvador Galindo-Valdés, Francisco Cepeda-Rodríguez, Josué Gómez-Casas, Nelly Abigaíl Rodríguez-Rosales, Oziel Gómez-Casas, Carlos Rodrigo Muñiz-Valdez

    In this research, the effect of the interelectrode distance (d) in the electrocoagulation (EC) reactor was studied. The experiments were carried out with varying d in values of 3, 5, and 9 mm during the treatment of water contaminated with fluoride (F−). The response variables analyzed were the treatment time necessary to reduce the residual concentration of F− to 1.5 mg L−1, the number of aluminum hydroxides formed, the potential drop in the reactor terminals, and the electric power consumption of the reactor. The software FLUENT version 6.3 was employed to simulate the liquid velocity profiles achieved in the reactor chamber. The results obtained show that the liquid velocity increases in the interelectrode spaces to 0.48, 0.65, and 0.86 m s−1 for interelectrode distances of 9, 5, and 3 mm, respectively, which favors not only the formation of flocs but also the elimination of fluoride. With a shorter interelectrode distance, the EC reactor not only consumes less electrical energy but also fewer electrodes, and the dispersion of generated flocs in the reactor chamber is major, which is more important than the quantity of flocs generated in it.


  • Open Access

    Statistical Data-Driven Model for Hardness Prediction in Austempered Ductile Irons

    by Nelly Abigaíl Rodríguez-Rosales, Félix Alan Montes-González, Oziel Gómez-Casas, Josué Gómez-Casas, Jesús Salvador Galindo-Valdés, Juan Carlos Ortiz-Cuellar, Jesús Fernando Martínez-Villafañe, Daniel García-Navarro, Carlos Rodrigo Muñiz-Valdez

    This research evaluates the effect of temperature and time austempering on microstructural characteristics and hardness of ductile iron, validating the results by means of a statistical method for hardness prediction. Ductile iron was subjected to austenitization at 950 °C for 120 min and then to austempering heat treatment in a salt bath at temperatures of 290, 320, 350 and 380 °C for 30, 60, 90 and 120 min. By increasing austempering temperature, a higher content of carbon-rich austenite was obtained, and the morphology of the thin acicular ferrite needles produced at 290 °C turned completely feathery at 350 and 380 °C. A thickening of acicular ferrite needles was also observed as austempering time increased. An inversely proportional behavior of hardness values was thus obtained, which was validated through data analysis, statistical tools and a regression model taking temperature and time austempering as input variables and hardness as the output variable, which achieved a correlation among variables of about 97%. The proposal of a mathematical model for the prediction of hardness in austempered ductile iron represents a numerical approximation which validates the experimental results at 95.20%.


  • Open Access

    Experimental Analysis and Mathematical Model of FSW Parameter Effects on the Corrosion Rate of Al 6061-T6-Cu C11000 Joints

    by Félix Alan Montes-González, Nelly Abigaíl Rodríguez-Rosales, Juan Carlos Ortiz-Cuellar, Carlos Rodrigo Muñiz-Valdez, Josué Gómez-Casas, Jesús Salvador Galindo-Valdés, Oziel Gómez-Casas

    Friction stir welding is characterized as an ecological and low-cost process in comparison to traditional welding techniques, and due to its application in the solid state, it is a feasible option for joining similar and/or dissimilar materials. The present investigation seeks to determine the effect of friction stir welding’s parameters on the corrosion resistance of an Al 6061-T6–Cu C11000 dissimilar joint, with mathematical analysis to validate the results. After the welding process, the samples were exposed to a NaCl solution in an electrochemical cell to determine the corrosion rate via potentiodynamic tests. Microstructural characterization revealed a laminar structure, composed of aluminum and copper, as well as copper particles and the formation of intermetallic compounds distributed in the weld zone. The potentiodynamic tests showed that the corrosion rate increased with the rotational and traverse speeds. The mathematical model quantifies the relationship between corrosion rate and rotational and traverse speeds.