Jesús Salvador Galindo-Valdés
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jesús Salvador Galindo-Valdés has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Rodrigo Muñiz-Valdez
Facultad de Ingeniería, Universidad Autónoma de Coahuila, Arteaga 25350, Coahuila, Mexico
10 shared publications - Jesús Fernando Martínez-Villafañe
Facultad de Ingeniería, Universidad Autónoma de Coahuila, Arteaga 25350, Coahuila, Mexico
7 shared publications - Josué Gómez-Casas
Faculty of Engineering, Autonomous University of Coahuila, Blvd. Fundadores km 13 University City, Arteaga 25350, Mexico
7 shared publications - Juan Carlos Ortiz-Cuellar
Facultad de Ingeniería, Universidad Autónoma de Coahuila, Arteaga 25350, Coahuila, Mexico
7 shared publications - Nelly Abigaíl Rodríguez-Rosales
Departamento de Metal Mecánica, Tecnológico Nacional de México/I.T. Saltillo, 25280 Saltillo, Coahuila, Mexico
4 shared publications - Nelly Abigaíl Rodríguez-Rosales
Departamento de Metal Mecánica, Tecnológico Nacional de México/I.T. Saltillo, Saltillo 25280, Coahuila, Mexico
4 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by MDPI AG in Inorganics
- Vol. 14 (10) , 266
Surface Modification of ZnO Nanoparticles with L-Serine and Preliminary Antibacterial Properties Against Escherichia coli
Due to bacterial mutation and evolution to survive and to the misuse of antibiotics, there is greater resistance to different medications among different bacteria. This study presents the modification of ZnO nanoparticles with L-serine via ultrasound, their physicochemical evaluation, and antibacterial performance against Escherichia coli (E. coli). Among the most significant results are: by FT-IR, a union between the carbonyl and amino groups of two L-serine amino acids was observed, indicating the formation of a peptide bond corresponding to amide group II. In the TGA of the samples modified with L-serine, weight losses between 360 and 455 °C were observed, supporting that the chemical modification was effective for both reaction times (60 and 90 min). In XRD, it could be observed that the characteristic peak of L-serine is at 22.8°, and there are other signals that oscillate between 10 and 20° of the peptide interlaces formed between the amino acids present in the modified particles. XPS analysis showed that, for the samples modified with L-serine, the N1s and C1s signals appeared, and deconvolution was performed for these signals in order to see their interactions in the chemical environment. The value of zeta potential of the sample ZnOMOD90 showed a bigger change. TEM images indicated that the ZnO pure nanoparticles have a hemispherical morphology and a size of approximately 24 nm, while ZnOMOD90 nanoparticles have a size of approximately 53 nm. Modified ZnO nanoparticles increased the inhibition zone halo for the ZnOMOD90 sample to 31 mm against E. coli bacteria, compared to pure ZnO, which had an inhibition zone of only 1 mm.
- 20 October 2026
- Published by MDPI AG in Inorganics
- Vol. 14 (10) , 266
Open AccessSurface Modification of ZnO Nanoparticles with L-Serine and Preliminary Antibacterial Properties Against Escherichia coli
Due to bacterial mutation and evolution to survive and to the misuse of antibiotics, there is greater resistance to different medications among different bacteria. This study presents the modification of ZnO nanoparticles with L-serine via ultrasound, their physicochemical evaluation, and antibacterial performance against Escherichia coli (E. coli). Among the most significant results are: by FT-IR, a union between the carbonyl and amino groups of two L-serine amino acids was observed, indicating the formation of a peptide bond corresponding to amide group II. In the TGA of the samples modified with L-serine, weight losses between 360 and 455 °C were observed, supporting that the chemical modification was effective for both reaction times (60 and 90 min). In XRD, it could be observed that the characteristic peak of L-serine is at 22.8°, and there are other signals that oscillate between 10 and 20° of the peptide interlaces formed between the amino acids present in the modified particles. XPS analysis showed that, for the samples modified with L-serine, the N1s and C1s signals appeared, and deconvolution was performed for these signals in order to see their interactions in the chemical environment. The value of zeta potential of the sample ZnOMOD90 showed a bigger change. TEM images indicated that the ZnO pure nanoparticles have a hemispherical morphology and a size of approximately 24 nm, while ZnOMOD90 nanoparticles have a size of approximately 53 nm. Modified ZnO nanoparticles increased the inhibition zone halo for the ZnOMOD90 sample to 31 mm against E. coli bacteria, compared to pure ZnO, which had an inhibition zone of only 1 mm.
- Open Access
Sonochemical Modification of ZrO2 Nanoparticles with Thiamine Hydrochloride for the Development of Films with PLA for the Adsorption of Hexavalent Chromium
Industrial wastewater can be reused in other everyday processes to help combat water scarcity worldwide. One contaminant in industrial wastewater is hexavalent chromium, which is highly toxic and can cause kidney, liver, and respiratory problems, making its removal vital. In this study, PLA-based films containing modified zirconia nanoparticles were developed via a solution-mixing process for hexavalent chromium adsorption. Obtaining the films involved two stages: the first was the chemical modification of ZrO2 nanoparticles with thiamine hydrochloride (vitamin B1) using fixed-frequency ultrasound at an output of 750 W and 50% amplitude for 60 min. The second stage involved preparing the films by mixing them in the solution using an ultrasonic bath. The nanoparticle concentrations were 0.25, 0.5, and 1 wt%. The results obtained from characterization using Fourier-transform infrared spectroscopy (FT-IR) revealed the characteristic bands of PLA and the characteristic peak of the Zr-O bond corresponding to the ZrO2 nanoparticles. Thermogravimetric analysis (TGA) showed that the ZrO2 nanoparticles provided thermal stability to the PLA polymer. X-ray diffraction (XRD) showed a broad peak of amorphous PLA at 16.8° and signals corresponding to the crystalline phase of ZrO2. The morphology of a cross-section of the films was observed using scanning electron microscopy (SEM), revealing a rough surface with pores. Finally, hexavalent chromium adsorption tests were carried out, measuring the adsorption efficiency under the parameters of pH, concentration, and contact time. The PLAZrO2 sample achieved an adsorption efficiency of 83% at pH 2.
Open AccessSonochemical Modification of ZrO2 Nanoparticles with Thiamine Hydrochloride for the Development of Films with PLA for the Adsorption of Hexavalent Chromium
Industrial wastewater can be reused in other everyday processes to help combat water scarcity worldwide. One contaminant in industrial wastewater is hexavalent chromium, which is highly toxic and can cause kidney, liver, and respiratory problems, making its removal vital. In this study, PLA-based films containing modified zirconia nanoparticles were developed via a solution-mixing process for hexavalent chromium adsorption. Obtaining the films involved two stages: the first was the chemical modification of ZrO2 nanoparticles with thiamine hydrochloride (vitamin B1) using fixed-frequency ultrasound at an output of 750 W and 50% amplitude for 60 min. The second stage involved preparing the films by mixing them in the solution using an ultrasonic bath. The nanoparticle concentrations were 0.25, 0.5, and 1 wt%. The results obtained from characterization using Fourier-transform infrared spectroscopy (FT-IR) revealed the characteristic bands of PLA and the characteristic peak of the Zr-O bond corresponding to the ZrO2 nanoparticles. Thermogravimetric analysis (TGA) showed that the ZrO2 nanoparticles provided thermal stability to the PLA polymer. X-ray diffraction (XRD) showed a broad peak of amorphous PLA at 16.8° and signals corresponding to the crystalline phase of ZrO2. The morphology of a cross-section of the films was observed using scanning electron microscopy (SEM), revealing a rough surface with pores. Finally, hexavalent chromium adsorption tests were carried out, measuring the adsorption efficiency under the parameters of pH, concentration, and contact time. The PLAZrO2 sample achieved an adsorption efficiency of 83% at pH 2.
- Open Access
Influence of Nd:YAG Laser Melting on an Investment-Casting Co-Cr-Mo Alloy
The investment casting process, also known as lost-wax casting, is widely used for producing ferrous and non-ferrous metal parts due to its excellent surface finish and dimensional accuracy. In recent years, the use of Co-Cr-Mo alloy has increased due to its high corrosion resistance, good biocompatibility, and relatively high wear resistance. Laser melting of materials has been demonstrated to refine the surface grain structure, reduce surface roughness, and improve both wear and corrosion resistance. The ability to fine-tune parameters such as laser power density and scanning speed facilitates the optimization of the treated layers’ thickness and homogeneity, thereby addressing many of the shortcomings inherent in conventional methods. This study investigates the microstructural, mechanical wear and bioactive behavior of investment-cast Co-Cr-Mo parts subjected to a Nd:YAG laser surface treatment. The effects of different processing parameters were analyzed quantitatively and comprehensively. The specimens were characterized using metallographic techniques, bioactivity evaluation, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), wear testing (Pin-on-Disk), and hardness testing. Our results demonstrate that Nd:YAG laser melting significantly enhances the surface properties and maintains the dimensional accuracy of complex Co-Cr-Mo biomedical components, through microstructural refinement, increased hardness, improved wear resistance, and preserved biocompatibility. The specific combination of investment casting with precisely controlled laser surface modification represents a significant advancement for improving the longevity and performance of biomedical implants.
Open AccessInfluence of Nd:YAG Laser Melting on an Investment-Casting Co-Cr-Mo Alloy
The investment casting process, also known as lost-wax casting, is widely used for producing ferrous and non-ferrous metal parts due to its excellent surface finish and dimensional accuracy. In recent years, the use of Co-Cr-Mo alloy has increased due to its high corrosion resistance, good biocompatibility, and relatively high wear resistance. Laser melting of materials has been demonstrated to refine the surface grain structure, reduce surface roughness, and improve both wear and corrosion resistance. The ability to fine-tune parameters such as laser power density and scanning speed facilitates the optimization of the treated layers’ thickness and homogeneity, thereby addressing many of the shortcomings inherent in conventional methods. This study investigates the microstructural, mechanical wear and bioactive behavior of investment-cast Co-Cr-Mo parts subjected to a Nd:YAG laser surface treatment. The effects of different processing parameters were analyzed quantitatively and comprehensively. The specimens were characterized using metallographic techniques, bioactivity evaluation, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), wear testing (Pin-on-Disk), and hardness testing. Our results demonstrate that Nd:YAG laser melting significantly enhances the surface properties and maintains the dimensional accuracy of complex Co-Cr-Mo biomedical components, through microstructural refinement, increased hardness, improved wear resistance, and preserved biocompatibility. The specific combination of investment casting with precisely controlled laser surface modification represents a significant advancement for improving the longevity and performance of biomedical implants.
- Open Access
Data-Driven Model for Cyclic Tasks of Robotic Systems: Study of the Repeatability Conditions
Ensuring repeatability in robotic manipulators is critical for industrial applications, particularly in cyclic tasks where precision and consistency are required. This study aims to establish the conditions that are necessary for repeatability in data-driven task-space control, compare repeatability across redundant robotic manipulators, and reduce the computational costs associated with data-based control methods compared to traditional model-based approaches. To achieve this, a large number of cyclic actions are simulated, mimicking real-world industrial routines. The methodology evaluates the estimated Jacobian matrix’s manipulability and its role in facilitating effective task execution within the operational space of the robot. The results demonstrate that the proposed approach achieves consistent repeatability at the full pose level of the end-effector, integrating both position and orientation. In particular, the findings indicate that the proposed controller minimizes variability and ensures reliable motion execution, even in the presence of system redundancies, as observed in the eight-DoF KUKA YouBot manipulator. These insights contribute to advancing data-driven control strategies for redundant robotic systems, enhancing their applicability in industrial settings.
Open AccessData-Driven Model for Cyclic Tasks of Robotic Systems: Study of the Repeatability Conditions
Ensuring repeatability in robotic manipulators is critical for industrial applications, particularly in cyclic tasks where precision and consistency are required. This study aims to establish the conditions that are necessary for repeatability in data-driven task-space control, compare repeatability across redundant robotic manipulators, and reduce the computational costs associated with data-based control methods compared to traditional model-based approaches. To achieve this, a large number of cyclic actions are simulated, mimicking real-world industrial routines. The methodology evaluates the estimated Jacobian matrix’s manipulability and its role in facilitating effective task execution within the operational space of the robot. The results demonstrate that the proposed approach achieves consistent repeatability at the full pose level of the end-effector, integrating both position and orientation. In particular, the findings indicate that the proposed controller minimizes variability and ensures reliable motion execution, even in the presence of system redundancies, as observed in the eight-DoF KUKA YouBot manipulator. These insights contribute to advancing data-driven control strategies for redundant robotic systems, enhancing their applicability in industrial settings.
- Open Access
- 2 June 2023
- Published by MDPI AG in Mathematics
- Vol. 11 (11) , 2555
Data-Driven Adaptive Modelling and Control for a Class of Discrete-Time Robotic Systems Based on a Generalized Jacobian Matrix Initialization
Data technology advances have increased in recent years, especially for robotic systems, in order to apply data-driven modelling and control computations by only considering the input and output signals’ relationship. For a data-driven modelling and control approach, the system is considered unknown. Thus, the initialization values of the system play an important role to obtain a suitable estimation. This paper presents a methodology to initialize a data-driven model using the pseudo-Jacobian matrix algorithm to estimate the model of a mobile manipulator robot. Once the model is obtained, a control law is proposed for the robot end-effector position tasks. To this end, a novel neuro-fuzzy network is proposed as a control law, which only needs to update one parameter to minimize the control error and avoids the chattering phenomenon. In addition, a general stability analysis guarantees the convergence of the estimation and control errors and the tuning of the closed-loop control design parameters. The simulations results validate the performance of the data-driven model and control.
- 2 June 2023
- Published by MDPI AG in Mathematics
- Vol. 11 (11) , 2555
Open AccessData-Driven Adaptive Modelling and Control for a Class of Discrete-Time Robotic Systems Based on a Generalized Jacobian Matrix Initialization
Data technology advances have increased in recent years, especially for robotic systems, in order to apply data-driven modelling and control computations by only considering the input and output signals’ relationship. For a data-driven modelling and control approach, the system is considered unknown. Thus, the initialization values of the system play an important role to obtain a suitable estimation. This paper presents a methodology to initialize a data-driven model using the pseudo-Jacobian matrix algorithm to estimate the model of a mobile manipulator robot. Once the model is obtained, a control law is proposed for the robot end-effector position tasks. To this end, a novel neuro-fuzzy network is proposed as a control law, which only needs to update one parameter to minimize the control error and avoids the chattering phenomenon. In addition, a general stability analysis guarantees the convergence of the estimation and control errors and the tuning of the closed-loop control design parameters. The simulations results validate the performance of the data-driven model and control.
- Open Access
Determination of Corrosion Resistance of High-Silicon Ductile Iron Alloyed with Nb
In this study, the effects of Nb on the microstructural characteristics, hardness, and corrosion resistance of high-silicon ductile cast iron (HSDI)-3.6 wt.% Si were investigated. Samples from different castings with 0–0.9 wt.% Nb were obtained and compared to a commercial ductile iron. Microstructures showed that the amount of ferrite in the matrix increased with increasing Nb content, from 34% for unalloyed HSDI to 88% for HSDI-0.9 wt.% Nb. The presence of randomly distributed NbC carbides was identified by EDX for all the samples alloyed with Nb, and the hardness of the HSDI increased with the Nb content. To evaluate the influence of the Nb content on the corrosion resistance of HSDI, potentiodynamic tests were carried out in a solution of H2SO4. The highest corrosion rate on HSDI was obtained for the HSDI-0.3 wt.% Nb sample, with 2802 mills per year, due to the amount of pearlite present and the lowest presence of NbC carbides, compared to the HSDI-0.9 wt.% Nb, with 986 mills per year. This behavior was attributed to the ferrite matrix obtained because of a high Si content in the DI, which delayed the anodic dissolution of the alloy and suppressed the pearlitizing effect of Nb for contents greater than 0.3 wt.%, as well as to the effect of NbC carbides, which acted as inhibitors.
Open AccessDetermination of Corrosion Resistance of High-Silicon Ductile Iron Alloyed with Nb
In this study, the effects of Nb on the microstructural characteristics, hardness, and corrosion resistance of high-silicon ductile cast iron (HSDI)-3.6 wt.% Si were investigated. Samples from different castings with 0–0.9 wt.% Nb were obtained and compared to a commercial ductile iron. Microstructures showed that the amount of ferrite in the matrix increased with increasing Nb content, from 34% for unalloyed HSDI to 88% for HSDI-0.9 wt.% Nb. The presence of randomly distributed NbC carbides was identified by EDX for all the samples alloyed with Nb, and the hardness of the HSDI increased with the Nb content. To evaluate the influence of the Nb content on the corrosion resistance of HSDI, potentiodynamic tests were carried out in a solution of H2SO4. The highest corrosion rate on HSDI was obtained for the HSDI-0.3 wt.% Nb sample, with 2802 mills per year, due to the amount of pearlite present and the lowest presence of NbC carbides, compared to the HSDI-0.9 wt.% Nb, with 986 mills per year. This behavior was attributed to the ferrite matrix obtained because of a high Si content in the DI, which delayed the anodic dissolution of the alloy and suppressed the pearlitizing effect of Nb for contents greater than 0.3 wt.%, as well as to the effect of NbC carbides, which acted as inhibitors.
- Open Access
- 24 September 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (19) , 12096
Interelectrode Distance Analysis in the Water Defluoridation by Electrocoagulation Reactor
In this research, the effect of the interelectrode distance (d) in the electrocoagulation (EC) reactor was studied. The experiments were carried out with varying d in values of 3, 5, and 9 mm during the treatment of water contaminated with fluoride (F−). The response variables analyzed were the treatment time necessary to reduce the residual concentration of F− to 1.5 mg L−1, the number of aluminum hydroxides formed, the potential drop in the reactor terminals, and the electric power consumption of the reactor. The software FLUENT version 6.3 was employed to simulate the liquid velocity profiles achieved in the reactor chamber. The results obtained show that the liquid velocity increases in the interelectrode spaces to 0.48, 0.65, and 0.86 m s−1 for interelectrode distances of 9, 5, and 3 mm, respectively, which favors not only the formation of flocs but also the elimination of fluoride. With a shorter interelectrode distance, the EC reactor not only consumes less electrical energy but also fewer electrodes, and the dispersion of generated flocs in the reactor chamber is major, which is more important than the quantity of flocs generated in it.
- 24 September 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (19) , 12096
Open AccessInterelectrode Distance Analysis in the Water Defluoridation by Electrocoagulation Reactor
In this research, the effect of the interelectrode distance (d) in the electrocoagulation (EC) reactor was studied. The experiments were carried out with varying d in values of 3, 5, and 9 mm during the treatment of water contaminated with fluoride (F−). The response variables analyzed were the treatment time necessary to reduce the residual concentration of F− to 1.5 mg L−1, the number of aluminum hydroxides formed, the potential drop in the reactor terminals, and the electric power consumption of the reactor. The software FLUENT version 6.3 was employed to simulate the liquid velocity profiles achieved in the reactor chamber. The results obtained show that the liquid velocity increases in the interelectrode spaces to 0.48, 0.65, and 0.86 m s−1 for interelectrode distances of 9, 5, and 3 mm, respectively, which favors not only the formation of flocs but also the elimination of fluoride. With a shorter interelectrode distance, the EC reactor not only consumes less electrical energy but also fewer electrodes, and the dispersion of generated flocs in the reactor chamber is major, which is more important than the quantity of flocs generated in it.
- Open Access
Statistical Data-Driven Model for Hardness Prediction in Austempered Ductile Irons
This research evaluates the effect of temperature and time austempering on microstructural characteristics and hardness of ductile iron, validating the results by means of a statistical method for hardness prediction. Ductile iron was subjected to austenitization at 950 °C for 120 min and then to austempering heat treatment in a salt bath at temperatures of 290, 320, 350 and 380 °C for 30, 60, 90 and 120 min. By increasing austempering temperature, a higher content of carbon-rich austenite was obtained, and the morphology of the thin acicular ferrite needles produced at 290 °C turned completely feathery at 350 and 380 °C. A thickening of acicular ferrite needles was also observed as austempering time increased. An inversely proportional behavior of hardness values was thus obtained, which was validated through data analysis, statistical tools and a regression model taking temperature and time austempering as input variables and hardness as the output variable, which achieved a correlation among variables of about 97%. The proposal of a mathematical model for the prediction of hardness in austempered ductile iron represents a numerical approximation which validates the experimental results at 95.20%.
Open AccessStatistical Data-Driven Model for Hardness Prediction in Austempered Ductile Irons
This research evaluates the effect of temperature and time austempering on microstructural characteristics and hardness of ductile iron, validating the results by means of a statistical method for hardness prediction. Ductile iron was subjected to austenitization at 950 °C for 120 min and then to austempering heat treatment in a salt bath at temperatures of 290, 320, 350 and 380 °C for 30, 60, 90 and 120 min. By increasing austempering temperature, a higher content of carbon-rich austenite was obtained, and the morphology of the thin acicular ferrite needles produced at 290 °C turned completely feathery at 350 and 380 °C. A thickening of acicular ferrite needles was also observed as austempering time increased. An inversely proportional behavior of hardness values was thus obtained, which was validated through data analysis, statistical tools and a regression model taking temperature and time austempering as input variables and hardness as the output variable, which achieved a correlation among variables of about 97%. The proposal of a mathematical model for the prediction of hardness in austempered ductile iron represents a numerical approximation which validates the experimental results at 95.20%.
- Open Access
Experimental Analysis and Mathematical Model of FSW Parameter Effects on the Corrosion Rate of Al 6061-T6-Cu C11000 Joints
Friction stir welding is characterized as an ecological and low-cost process in comparison to traditional welding techniques, and due to its application in the solid state, it is a feasible option for joining similar and/or dissimilar materials. The present investigation seeks to determine the effect of friction stir welding’s parameters on the corrosion resistance of an Al 6061-T6–Cu C11000 dissimilar joint, with mathematical analysis to validate the results. After the welding process, the samples were exposed to a NaCl solution in an electrochemical cell to determine the corrosion rate via potentiodynamic tests. Microstructural characterization revealed a laminar structure, composed of aluminum and copper, as well as copper particles and the formation of intermetallic compounds distributed in the weld zone. The potentiodynamic tests showed that the corrosion rate increased with the rotational and traverse speeds. The mathematical model quantifies the relationship between corrosion rate and rotational and traverse speeds.
Open AccessExperimental Analysis and Mathematical Model of FSW Parameter Effects on the Corrosion Rate of Al 6061-T6-Cu C11000 Joints
Friction stir welding is characterized as an ecological and low-cost process in comparison to traditional welding techniques, and due to its application in the solid state, it is a feasible option for joining similar and/or dissimilar materials. The present investigation seeks to determine the effect of friction stir welding’s parameters on the corrosion resistance of an Al 6061-T6–Cu C11000 dissimilar joint, with mathematical analysis to validate the results. After the welding process, the samples were exposed to a NaCl solution in an electrochemical cell to determine the corrosion rate via potentiodynamic tests. Microstructural characterization revealed a laminar structure, composed of aluminum and copper, as well as copper particles and the formation of intermetallic compounds distributed in the weld zone. The potentiodynamic tests showed that the corrosion rate increased with the rotational and traverse speeds. The mathematical model quantifies the relationship between corrosion rate and rotational and traverse speeds.
- Open Access
Effects of the FSW Parameters on Microstructure and Electrical Properties in Al 6061-T6- Cu C11000 Plate Joints
Friction Stir Welding (FSW) is a feasible welding process to join dissimilar materials due to its solid-state nature. In this study the FSW of 6061-T6 aluminum with pure Cu plates was performed with the objective of evaluating the effects of the FSW parameters on the microstructure and electrical properties. The processing parameters (rotational and traverse speeds) were established to reduce the common defects in the friction-stir welding process. Therefore, the obtained results validated the better mechanical properties and a smaller increase of the electrical resistivity. The rotational speeds used were of 1000, 1150, and 1300 rpm, and the traverse speeds of 20, 40, and 60 mm/min, with the purpose of varying the heat input of the process. The microstructural characterization revealed the presence of a mixture of aluminum and copper into the weld zone, along with copper particles and the formation of intermetallic compounds. It was found that the electrical resistivity of the joints ranged from 0.029 to 0.036 μΩ. The highest electrical resistivity values were obtained at the lowest traverse speed (20 mm/min) and the lowest resistivity values were obtained at highest traverse speed (60 mm/min).
Open AccessEffects of the FSW Parameters on Microstructure and Electrical Properties in Al 6061-T6- Cu C11000 Plate Joints
Friction Stir Welding (FSW) is a feasible welding process to join dissimilar materials due to its solid-state nature. In this study the FSW of 6061-T6 aluminum with pure Cu plates was performed with the objective of evaluating the effects of the FSW parameters on the microstructure and electrical properties. The processing parameters (rotational and traverse speeds) were established to reduce the common defects in the friction-stir welding process. Therefore, the obtained results validated the better mechanical properties and a smaller increase of the electrical resistivity. The rotational speeds used were of 1000, 1150, and 1300 rpm, and the traverse speeds of 20, 40, and 60 mm/min, with the purpose of varying the heat input of the process. The microstructural characterization revealed the presence of a mixture of aluminum and copper into the weld zone, along with copper particles and the formation of intermetallic compounds. It was found that the electrical resistivity of the joints ranged from 0.029 to 0.036 μΩ. The highest electrical resistivity values were obtained at the lowest traverse speed (20 mm/min) and the lowest resistivity values were obtained at highest traverse speed (60 mm/min).