DYDenys Yakhno

Denys Yakhno

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Denys Yakhno has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    THE INFLUENCE OF CUTTING TIME ON THE VIBRATION PARAMETERS DURING FINISH MILLING

    by Sergei Dyadya, Olena Kozlova, Denys Yakhno, Hanna Sudnyk

    The article considers the possibility of using cutting time to determine cutting conditions through the calculation of the determining ratio. One of the five speed zones of oscillation is determined by its value. Among them, the third speed oscillation zone is the most unfavorable for obtaining the quality of the machined surface. To exit this zone without reducing the cutting speed, it is proposed to use technological techniques that increase the cutting time. In particular, by increasing the angle of inclination of the helical cutting edge of the end mill. This allows you to assign such a value of the angle of inclination at which, due to the cutting time, the value of the determining ratio approaches the second speed oscillation zone, in which the damping properties of the cutting process significantly reduce the intensity of oscillations and ensure stable milling.

  • INFLUENCE OF HELICAL CUTTING-EDGE ANGLE ON END-MILLING STABILITY

    by Sergei Dyadya, Olena Kozlova, Pavlo Tryshyn, Denys Yakhno, Denys Dziuba

    Increasing productivity, machining accuracy and efficient use of resources are important priorities for companies that manufacture competitive products. One of the main problems that hinders these processes is the vibration that occurs during cutting. Various methods are used to suppress vibration, one of which is the use of tools with a variable helical cutting-edge angle. However, when choosing the cutting-edge angle, it is important to consider the types of vibrations that occur during cutting, as they directly affect the efficiency of the milling process. In addition, the use of tools with different cutting-edge geometries, such as wavy, gives positive results in roughing, but becomes ineffective in finishing. The purpose of this paper is to study the effect of the helical cutting-edge angle on the stability of the end-milling at different cutting speeds. Both theoretical aspects and experimental data are considered, which make it possible to evaluate the effectiveness of using tools with different angles of inclination to ensure the stability of the machining process and increase productivity while minimizing vibrations in the most unfavorable third speed zone of oscillations for cutting. To conduct the experiments, a special stand was used to adjust the stiffness of the workpiece, record the vibrations that occur during cutting, and the time of contact between the workpiece and the tool. The milling was performed in the third high-speed oscillation zone using a tool whose design provides for the possibility of adjusting the angle of inclination of the helical cutting edge. Studies confirm that changing the angle of inclination can significantly affect the stability of the milling process, reducing the intensity of oscillations and improving machining accuracy. However, this effect depends on the initial cutting conditions, such as the cutting speed. With its increase, the amplitude of the accompanying free oscillations increases, regardless of the value of the angle of inclination. Ensuring the stability of the end-milling in the third speed zone by changing the angle of inclination is possible only at the speeds that determine the beginning of this zone. However, within the entire speed range covered by the third speed zone, it is impossible to ensure a stable milling process only due to the angle of inclination. The study emphasizes the importance of an integrated approach to selecting cutting parameters to achieve process stability.


  • Open Access

    INFLUENCE OF FEED RATE ON THE DYNAMIC PROPERTIES OF THIN-WALLED PART DURING END-MILLING

    by Sergei Dyadya, Olena Kozlova, Eduard Brukhno, Denys Yakhno, Daria Karamushka

    When selecting cutting modes for end-milling of thin-walled parts from hard-to-machine materials, their influence on machining stability must be considered. To do this, it is necessary to understand the types of vibrations that operate and the conditions under which they arise. Research has shown that different types of vibrations operate sequentially during cutting and only for a certain of time. During end-milling, forced and accompanying free oscillations operates due to the short duration of cutting. Their influence on the stability of the cutting process depends on the speed zone in which the milling takes place. The most unfavorable is the third speed zone of vibrations, where accompanying free vibrations of high intensity occur. Cutting speeds for machining parts from hard-to-machine materials fall precisely within this zone. The intensity of vibrations is influenced by the dynamic properties of the part. During end-milling of thin-walled parts, these properties are characterized by the amplitude and frequency of accompanying free vibrations, which exceed the natural frequency of the part's free vibrations. In other words, cutting modes alter the dynamic properties of the part. Some researchers focus on utilizing the damping properties of the feed. Therefore, the aim of this paper was to determine how the feed affects the dynamic properties of the part during cutting. A universal stand was used for the investigation, which allows for the creation of various dynamic characteristics of the processed sample and recording its motion laws during milling on an oscillogram. The research results showed that the feed, as an element of cutting modes, influences the dynamic properties of the part during cutting. It creates a variable layer that is being cut. Therefore, during the cutting time, the frequency and amplitude of accompanying free vibrations change during both up- and down milling. The feed affects the dynamic stiffness. Increasing the feed increases the dynamic stiffness of the part. This leads to a reduction in the amplitude of accompanying free vibrations during milling in the third speed zone of vibrations. The results presented in the article have practical significance for technologists in the aviation manufacturing industry. They help to better understand the physical processes occurring during milling and develop optimal processing strategies for thin-walled parts, which have high requirements for dimensional accuracy and surface quality. При призначенні режимів різання для кінцевого фрезерування тонкостінних деталей з важкооброблюваних матеріалів треба враховувати їх вплив на сталість обробки. Для цього треба знати, які види коливань діють і за яких умов вони виникають. Виконаними дослідженнями встановлено, що при різанні різні види коливань діють послідовно і тільки певний час. При кінцевому фрезеруванні через короткочасність різання виникають вимушені та супроводжуючі вільні коливання. Їх вплив на сталість процесу різання залежить від того, в якій швидкісній зоні коливань буде проходити фрезерування. Найбільш несприятливою є третя швидкісна зона коливань. Тільки в ній діють супроводжуючі вільні коливання великої інтенсивності. Швидкості різання для обробки деталей з важкооброблюваних матеріалів припадають саме на цю зону. На інтенсивність коливань впливають динамічні властивості деталі. При кінцевому фрезеруванні тонкостінних деталей вони характеризуються амплітудою та частотою супроводжуючих вільних коливань, які більше за частоту вільних коливань деталі. Тобто режими різання змінюють динамічні властивості деталі. Деякі дослідники зосереджуються на використанні демпфуючих властивостей подачі. Тому метою даної роботи було визначення того, яким чином подача впливає на динамічні властивості деталі при різанні. Для дослідження використовувався універсальний стенд, за допомогою якого можливо створювати різні динамічні характеристики зразка, який обробляється та записувати на осцилограмі закони його руху при фрезеруванні. Результати досліджень показали, що подача, як елемент режимів різання, впливає на динамічні властивості деталі при різанні. Вона створює змінний шар, який зрізається. Тому на протязі часу різання частота і амплітуда супроводжуючих вільних коливань при зустрічному і попутному фрезеруванні змінюються. Подача впливає на динамічну жорсткість. При збільшенні подачі...


  • Open Access

    INFLUENCE OF RADIAL DEPTH OF CUT ON INITIAL CONDITIONS OF OSCILLATIONS DURING END-MILLING OF THIN-WALLED PARTS

    by Sergei Dyadya, Olena Kozlova, Pavlo Tryshyn, Eduard Brukhno, Denys Yakhno

    Milling is widely used in mechanical engineering and other industries. Optimization of this process can lead to improved quality of machined parts, increased productivity and reduced wear of equipment. The paper investigates an important aspect of the milling process, namely the influence of radial depth of cut on the properties of the tool-part technological system (TS) and the amplitude of vibrations during machining. Vibrations can be a direct cause of reduction of quality and accuracy of machined parts. When the amplitude of vibrations increases, their impact on accuracy becomes critical. The analysis of studies of up and down end-milling with different radial depths of cut in the third speed zone of oscillations shows that with increasing radial depth of cut the cutting time and maximum thickness of the cut layer increases. This affects the length of the cutting surface and the character of the workpiece oscillations during up and down-milling. The length of the cutting surface determines how many waves of accompanying free oscillations of the TS and with what intensity will leave their trace on the cutting surface. In up-milling, the thickness of the cut layer increases with increasing radial depth of cut, while the amplitude of the accompanying free oscillations TS and their period decrease. At down milling the thickness of the cut layer decreases, and the amplitude of accompanying free oscillations of the TS and their period increase. A common characteristic feature of up and down-milling is the shaping of the machined surface in the cutting zone with a small thickness of the cut layer. In up-milling, this area is at the beginning of cutting, when the oscillation conditions are the same for all radial cutting depths. Therefore, the machined surfaces after up-milling with different radial cutting depths have close values of pitch and undulation height. At down-milling with increasing radial depth of cut, the amplitude of accompanying free oscillations of the TS in the profiling zone increases. This leads to an increase in the pitch and height of undulations on the machined surface. When milling in the third speed oscillation zone, it is necessary to select the radial depth of cut so that the cutting time is less than the period of the accompanying free oscillations of the TS. This will avoid undesirable oscillations and improve the quality of machining. The paper provides important results and recommendations for optimizing the milling process, considering the influence of radial depth of cut on TS properties and vibration amplitude. These findings may be useful for professionals working in the field of cutting materials processing to improve the efficiency and quality of production processes.