OKOlena Kozlova

Olena Kozlova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Olena Kozlova has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    ANALYSIS OF THE DEVELOPMENT OF SCIENTIFIC CONCEPTS ABOUT THE PHYSICAL BASIS OF EXCITATION AND SUPPRESSION OF SELF-OSCILLATION DURING TURNING

    by Pavlo Tryshyn, Olena Kozlova, Natalia Honchar, Andri Levchenko

    Purpose. The purpose of the work is to analyze the evolution of scientific ideas about the physical mechanisms of excitation and suppression of self-oscillations during turning, to generalize modern theoretical and experimental research, to determine the main mechanisms of self-excitation of self-oscillations, to evaluate existing approaches to their study and to identify unresolved scientific issues that require further research. Research methods. Methods of analysis, comparison, generalization and systematization of scientific sources, historical-scientific and logical analysis of the development of the theory of self-oscillations during turning, as well as a critical analysis of modern theoretical and experimental research on the physical mechanisms of their excitation and suppression were used. Results. An analysis of the development of scientific ideas about the physical mechanisms of excitation and suppression of self-oscillations during turning was conducted. The main theories of the occurrence of self-oscillations were systematized, their advantages and limitations were determined, and unresolved scientific issues were outlined that justify the need for further theoretical and experimental research. Scientific novelty. Modern scientific ideas about the physical mechanisms of excitation and suppression of self-oscillations during turning are systematized, the main theoretical approaches are summarized, and unresolved issues that require further experimental and theoretical research are identified. Practical value. The results of the work can be used to substantiate the directions of further research into the physical mechanisms of self-oscillations during turning, improve methods for predicting the vibration stability of the cutting process, and develop technological methods for suppressing self-oscillations.

  • Open Access

    INFLUENCE OF THE TYPE OF CHIP FORMATION ON THE EXCITATION OF REGENERATIVE SELF-OSCIENCES DURING TURNING

    by Pavlo Tryshyn, Olena Kozlova, Yuriy Vnukov, Andriy Levchenko

    The paper presents the results of an experimental study of the influence of the type of chip formation on the occurrence and development of regenerative self-oscillations during turning. The relationship between the nature of chip formation and the dynamic stability of the technological system in the cutting process is considered. Experimental studies were conducted when processing various structural materials that differ in the mechanism of plastic deformation and the nature of chip formation. It was established that when processing materials that form flowing chips, such as steel 45, copper M2, aluminum alloy D16 and lead C1, stable regenerative self-oscillations arise at certain ranges of cutting speeds. Their appearance is due to the relatively continuous nature of the plastic deformation of the material and the stable formation of the cut layer. Under these conditions, a positive feedback loop is formed between the change in the thickness of the cut layer and the oscillations of the elements of the technological system, which leads to the development of regenerative self-oscillations and a decrease in the stability of the cutting process. At the same time, during the processing of materials characterized by segmental chip formation, regenerative self-oscillations were not observed. The periodic formation of chip segments with a certain frequency and the adiabatic nature of the displacement of these segments can lead to the damping of regenerative self-oscillations. The results obtained show that the type of chip formation is one of the significant factors affecting the dynamic stability of the turning process. Confluent chip formation contributes to the emergence and development of regenerative self-oscillations, while segmental chip formation can completely suppress their development.

  • QUALITY OF MACHINED SURFACES OF THIN-WALLED ELEMENTS OF PARTS UNDER THE ACTION OF REGENERATIVE VIBRATIONS DURING MILLING WITH END MILLS

    by Sergiy Dyadya, Olena Kozlova, Pavlo Tryshyn, Eduard Kondratiuk, Oleksiy Kramarenko

    Monowheels, in which the disk and working blades constitute a single structure without detachable connections, are critically important components of new generation gas turbine engines for aviation and power engineering. The use of such structures allows to reduce the weight and increase the reliability of the units. However, errors in the shape of the functional surfaces of the blades that arise during mechanical processing lead to a decrease in the engine efficiency and an increase in fuel consumption. To ensure the accuracy of manufacturing the functional surfaces of the blades during the technological process, it is necessary to know the conditions under which cutting occurs. The work uses an approach based on the distribution of the entire range of cutting speeds into five speed oscillation zones. It was established that the third speed zone is the most unfavorable during milling of blades on multi-coordinate CNC machines. It is characterized by high-intensity vibrations, which worsens the quality of the machined surface and reduces the stability of the cutter. Their cause is regenerative oscillations, which are excited during machining by the trace left on the cutting surface by the accompanying free oscillation. The purpose of the study is to determine the influence of the axial depth of cut on the quality of the machined surface during milling in the third speed zone of vibrations. The results of the experiments showed that due to the peculiarities of up-milling with an axial depth of cut of ap = 1 mm, waviness on the machined surface is not formed, even in the presence of regenerative oscillations. The obtained data allow us to develop recommendations for the selection of cutting modes that minimize the amplitude of oscillations and ensure that the monowheel blades meet high operational requirements.

  • Open Access

    THE INFLUENCE OF CUTTING TIME ON THE VIBRATION PARAMETERS DURING FINISH MILLING

    by Sergei Dyadya, Olena Kozlova, Denys Yakhno, Hanna Sudnyk

    The article considers the possibility of using cutting time to determine cutting conditions through the calculation of the determining ratio. One of the five speed zones of oscillation is determined by its value. Among them, the third speed oscillation zone is the most unfavorable for obtaining the quality of the machined surface. To exit this zone without reducing the cutting speed, it is proposed to use technological techniques that increase the cutting time. In particular, by increasing the angle of inclination of the helical cutting edge of the end mill. This allows you to assign such a value of the angle of inclination at which, due to the cutting time, the value of the determining ratio approaches the second speed oscillation zone, in which the damping properties of the cutting process significantly reduce the intensity of oscillations and ensure stable milling.

  • Open Access

    INFLUENCE OF DISCONTINUOUS CHIP FORMATION ON THE EXCITATION OF REGENERATIVE SELF-OSCILLATIONS DURING TURNING

    by Pavlo Tryshyn, Olena Kozlova, Yuriy Vnukov, Andriy Levchenko

    Purpose. The objective of this study is to investigate the influence of discontinuous chip formation on the excitation of regenerative self-oscillations during turning, to compare the vibration for continuous and discontinuous chip formation mechanisms, and to improve the prediction of machining stability for brittle materials. Research methods. The study was carried out under conditions of continuous orthogonal turning using a CNC lathe. Vibration was investigated with a single degree of freedom cutter–oscillator designed in the direction of chip thickness variation. The displacement of the cutting edge during machining was measured using an inductive sensor, and the signals were recorded through a multi-channel data acquisition system and processed on a computer. Oscillograms were analyzed to determine vibration amplitude and static deflection. Results. The experimental results showed that the type of chip formation has a significant influence on vibration during turning. When machining steel AISI 1045, characterized by continuous chip formation, pronounced regenerative chatter was observed in the cutting speed range of v=100–250 m/min, with vibration amplitude increasing as cutting speed increased. In contrast, during machining of gray cast iron GG35, which produces discontinuous chips, no regenerative chatter was detected; only low-amplitude random vibrations were present, and their level remained nearly constant over the entire cutting speed range. For bronze CuSn3Zn13Pb4, also characterized by discontinuous chip formation, regenerative chatter occurred only at higher cutting speeds (v=150–250 m/min), and the vibration amplitude increased with cutting speed similarly to steel. Scientific novelty. The scientific novelty of this study lies in establishing the influence of discontinuous chip formation on the suppression and excitation conditions of regenerative self-oscillations during turning. Practical value. The practical significance of this study lies in improving the prediction of machining stability when processing materials with different chip formation mechanisms. The obtained results can be used to select optimal cutting conditions that reduce or prevent regenerative self-oscillations, especially when machining brittle materials.

  • Development of Oscillating Systems for Studying Self-oscillations in Turning

    by Yuriy Vnukov, Pavlo Tryshyn, Serhiy Dyadya, Olena Kozlova

  • Open Access

    The Influence of Spindle Speed Variation on the Suppression of Self‐Oscillations During Turning

    by Pavlo Tryshyn, Yuriy Vnukov, Olena Kozlova

    This paper presents the results of a study examining the effect of the spindle speed variation (SSV) mode on the suppression of self‐oscillations (chatter) during turning. Particular attention is paid to analyzing the effectiveness of the SSV mode for various types of self‐oscillations (regenerative, tangential, and coupled). Experimental studies revealed that SSV affects different chatter mechanisms unequally. The amplitude of regenerative self‐oscillations decreased only by 1.2…1.62 times, indicating the high stability of the regenerative feedback mechanism under variable spindle speed conditions. In contrast, tangential self‐oscillations were suppressed significantly more effectively, with amplitude reductions reaching 3.66…4.61 times. Coupled self‐oscillations were also effectively suppressed: the vibration amplitude along the X axis decreased by 1.5…1.62 times, while along the Z axis it decreased by 2.24…2.5 times. This behavior is associated with the direct influence of SSV on instantaneous cutting speed. The obtained results confirm that regenerative self‐oscillations are highly stable and are the most difficult to suppress during turning. Therefore, to effectively dampen regenerative self‐oscillations, it is necessary to use additional methods, for example, an enlarged wear area on the flank surface of the cutter.

  • Open Access

    CALCULATION OF PARAMETERS OF A CUTTER-OSCILLATOR WITH TWO DEGREES OF FREEDOM

    by Pavlo Tryshyn, Olena Kozlova, Yuriy Vnukov

    Purpose. The main purpose of the work is to conduct a comprehensive assessment of the parameters of a cutter-oscillator with two degrees of freedom using three methods: analytical, computer, and experimental. Research methods. The analytical approach included determining the natural frequency of oscillations and the angle of the resulting displacement of the cutter-oscillator with two degrees of freedom. For numerical modeling of the cutter-oscillator, the SolidWorks and NX software packages were used. The research was also conducted by an experimental method, within which the oscillograms of the oscillations of the cutting edge were recorded. On their basis, the static deflection of the cutter-oscillator and the frequency of its free oscillations were determined. Results. As a result of the study, it was found that the use of an cutter-oscillator is effective for determining the dynamic characteristics of the turning process. The analytical method made it possible to obtain preliminary estimates of the frequencies of natural oscillations and the direction of the resulting displacement. Computer modeling in SolidWorks and NX provided increased accuracy of calculations and allowed varying the system parameters without additional experiments. Experimental measurements based on the analysis of the oscillograms of the cutting edge oscillations confirmed the consistency of the theoretical and model data. The obtained results prove the reliability of the adopted models and the feasibility of using computer modeling for further improvement of the dynamic analysis of the turning process. Scientific novelty. The scientific novelty of the work lies in the integrated approach to the study of the dynamic characteristics of a cutter-oscillator with two degrees of freedom, which combines analytical, numerical and experimental methods of evaluation. Practical value. The practical value of the work lies in the development and justification of a methodology for evaluating the dynamic parameters of a two degree of freedom cutter-oscillator, which can be used during the design and adjustment of tool systems in the turning process. The use of computer modeling allows you to change quickly the design parameters of the tool without conducting a significant number of experiments, reducing the cost of time and resources. The obtained results can be implemented in production practice and used to improve dynamic control systems in metalworking.

  • About Cut Thickness in Vibration Tracking Cutting

    by Yuriy Vnukov, Pavlo Tryshyn, Serhiy Dyadya, Olena Kozlova

  • Open Access

    MODELING THE ANGLE OF THE DIRECTION OF THE RESULTING DISPLACEMENT OF THE CUTTING EDGE OF THE CUTTER-OSCILLATOR

    by Pavlo Tryshyn, Olena Kozlova, Natalia Honchar, Andrey Levchenko, Павло Тришин, Наталя Гончар

    Purpose. Establishing the dependence of the angle of the direction of the resulting displacement of the cutting edge of the cutter-oscillator on the geometric parameters of the holder using various methods and substantiating the feasibility of using cutter-oscillators with single degree of freedom for targeted modeling of the influence of individual factors, such as the regenerative effect or a change in the instantaneous cutting speed. Research methods. The analytical method involved obtaining calculation formulas for determining the angle of the direction of the resulting displacement of the cutter-oscillator. For numerical modeling of the bending of the cutter-oscillator during turning, the SolidWorks and Unigraphics NX programs were used. The research was also conducted by an experimental method, in which oscillograms of the oscillations of the cutting edge were recorded, from which the static bending of the cutter-oscillator was determined. Results. Methods for determining the direction of the resulting displacement of the cutting edge of the cutter-oscillator have been developed based on analytical calculation, computer modeling, and experimental methods. Computer modeling of the bends of the cutters-oscillator has been carried out in the SolidWorks program, which made it possible to determine with high accuracy the angle of the direction of the resulting displacement of the cutting edge at different ratios of the cutter- oscillator holder dimensions. It has been shown that the optimal ratio of the height to the width of the holder (h/b > 3.3 for the oscillator X; h/b < 0.3 for the oscillator Z) provides the direction of movement with a deviation of no more than 5° from the X and Z axes, respectively. The accuracy of the computer modeling method has been experimentally confirmed, which allows it to be used for designing cutters-oscillators with specified dynamic properties. Scientific novelty. The optimal dependence of the angle of the direction of displacement of the cutting edge of the cutter-oscillator on the geometric parameters of the holder has been established, which allows controlling the orientation of oscillations during cutting. Practical value. The results of the work can be used in the design of cutters-oscillators to study the dynamics of the turning process. The developed methodology allows reducing the costs of manufacturing prototypes of cutters-oscillators due to preliminary modeling of their characteristics in the CAD/CAM environment.