Kaiming Niu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kaiming Niu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bo Tian
School of Civil Engineering, Chongqing Jiaotong University, Chongqing 400074, China
1 shared publication - Guoman Yu
Construction Project Headquarters of Nujiang Beautiful Highway Greenway, Nujiang 673200, China
1 shared publication - Jianrui Ji
School of Civil Engineering, Chongqing Jiaotong University, Chongqing 400000, China
1 shared publication - Jilin Zhang
School of Civil Engineering, Chongqing Jiaotong University, Chongqing 400074, China
1 shared publication - Liangliang Chen
Yunnan Provincial Transportation Planning and Design Research Institute Co., Ltd., Kunming 650000, China
1 shared publication - Lihui Li
School of Civil Engineering, Chongqing Jiaotong University, Chongqing 400074, China
1 shared publication
Latest Publications
- Open Access
Study on High-Temperature Activated Products and Hydration Properties of Aga Soil in Tibet for Cement Concrete
In order to impart the properties of cementitious material to the Tibetan Agar soil, two high-temperature activation mechanisms (HTMA, HTMB) were designed in this study, and the products and hydration-hardening properties of Tibetan Agar soil high-temperature activation mechanism were analyzed by means of SEM, XRD, and XRF. The results show that the main components of Tibetan Aga soil are calcite and quartz; Aga soil is activated by HTMA high-temperature activation, forming the main products of CaO, C2S, CaSiO3, and CaAl2Si2O8, and its products have both air-hardening and water-hardening characteristics; Aga soil is activated by HTMB high-temperature activation, and when the temperature reaches 1250 °C when the clinker is not found in the CaO, the generation of C2S, C3S, C3A, C4AF, and Mg2SiO4 minerals with good water-hardening cementitious properties occurs when the temperature rises to 1350 °C, although the formation of some inert minerals that do not have the cementitious properties, but this temperature activation products of the thermodynamic properties of the best; Enhancing the value of lime saturation degree (KH) and silicon rate (SM) can promote the formation of the products of the C2S and C3S, increase the reactivity of the Aga soil activation products, and increase the hydration heat as well as compressive and flexural strength, combined with the results of the hydration heat and mechanical test, KH is recommended to be 0.9~0.94, SM is recommended to be 1.8~2.4, and alumina ratio (IM) is recommended to be 1.8~2.4 when Aga soil is used with raw materials.
Open AccessStudy on High-Temperature Activated Products and Hydration Properties of Aga Soil in Tibet for Cement Concrete
In order to impart the properties of cementitious material to the Tibetan Agar soil, two high-temperature activation mechanisms (HTMA, HTMB) were designed in this study, and the products and hydration-hardening properties of Tibetan Agar soil high-temperature activation mechanism were analyzed by means of SEM, XRD, and XRF. The results show that the main components of Tibetan Aga soil are calcite and quartz; Aga soil is activated by HTMA high-temperature activation, forming the main products of CaO, C2S, CaSiO3, and CaAl2Si2O8, and its products have both air-hardening and water-hardening characteristics; Aga soil is activated by HTMB high-temperature activation, and when the temperature reaches 1250 °C when the clinker is not found in the CaO, the generation of C2S, C3S, C3A, C4AF, and Mg2SiO4 minerals with good water-hardening cementitious properties occurs when the temperature rises to 1350 °C, although the formation of some inert minerals that do not have the cementitious properties, but this temperature activation products of the thermodynamic properties of the best; Enhancing the value of lime saturation degree (KH) and silicon rate (SM) can promote the formation of the products of the C2S and C3S, increase the reactivity of the Aga soil activation products, and increase the hydration heat as well as compressive and flexural strength, combined with the results of the hydration heat and mechanical test, KH is recommended to be 0.9~0.94, SM is recommended to be 1.8~2.4, and alumina ratio (IM) is recommended to be 1.8~2.4 when Aga soil is used with raw materials.
- Open Access
Analyzing Pore Evolution Characteristics in Cementitious Materials Using a Plane Distribution Model
This research aims to analyze the distribution and evolution of pores within the planar structure of cement-based materials. Utilizing digital imaging methods, a model for pore plane distribution was established, and the evolutionary patterns of both total pore numbers and varying pore sizes in cement-based materials were investigated. The research introduced an innovative experimental method for analyzing pore distribution within cement-based planar structures. Additionally, a hybrid method was proposed, combining automated image binarization thresholding with manual comparative analysis, thereby enhancing the feasibility of comparative research. Pores were categorized into four distinct sizes: tiny pores (5–200 μm), small pores (200–500 μm), medium pores (500–1000 μm), and large pores (>1000 μm). Areas with apertures <5 μm were classified as dense areas. The findings indicated that the overall number of pores in cement-based materials increased due to the influence of styrene butadiene latex additives. However, at a 15% dosage, the rate of pore formation reached an inflection point, confirming that various factors, such as styrene butadiene latex, air bubbles, and the cement-based material itself, collectively influenced pore formation. The research also demonstrated that styrene butadiene latex affected the four categorized pore sizes differently. Importantly, a higher latex dosage did not necessarily lead to a proportional increase in pore content. Pore content was influenced by multiple factors and exhibited different distribution patterns. The number of micropores, although relatively small, gradually increased with higher latex dosages, while small and medium pores generally showed an upward trend. At a 10% latex dosage, both small and medium pores reached a turning point in their rate of increase. Large pores also exhibited a general increase, peaking at a latex dosage of 10%. It was confirmed that both the total pore volume and the content of micropores were critical factors in determining the mechanical properties of cementitious materials. Higher porosity and micropore content generally weakened mechanical performance. However, at a small latex dosage, there was an improvement in flexural strength. When the latex dosage reached 15%, the total pore and micropore content declined, resulting in a balanced increase in flexural strength and a mitigated decline in compressive strength. This study offers valuable insights into the evolution of total pore volume and the content of pores of various sizes, providing a theoretical basis for the meticulous selection of additive types and dosages from a microscopic perspective.
Open AccessAnalyzing Pore Evolution Characteristics in Cementitious Materials Using a Plane Distribution Model
This research aims to analyze the distribution and evolution of pores within the planar structure of cement-based materials. Utilizing digital imaging methods, a model for pore plane distribution was established, and the evolutionary patterns of both total pore numbers and varying pore sizes in cement-based materials were investigated. The research introduced an innovative experimental method for analyzing pore distribution within cement-based planar structures. Additionally, a hybrid method was proposed, combining automated image binarization thresholding with manual comparative analysis, thereby enhancing the feasibility of comparative research. Pores were categorized into four distinct sizes: tiny pores (5–200 μm), small pores (200–500 μm), medium pores (500–1000 μm), and large pores (>1000 μm). Areas with apertures <5 μm were classified as dense areas. The findings indicated that the overall number of pores in cement-based materials increased due to the influence of styrene butadiene latex additives. However, at a 15% dosage, the rate of pore formation reached an inflection point, confirming that various factors, such as styrene butadiene latex, air bubbles, and the cement-based material itself, collectively influenced pore formation. The research also demonstrated that styrene butadiene latex affected the four categorized pore sizes differently. Importantly, a higher latex dosage did not necessarily lead to a proportional increase in pore content. Pore content was influenced by multiple factors and exhibited different distribution patterns. The number of micropores, although relatively small, gradually increased with higher latex dosages, while small and medium pores generally showed an upward trend. At a 10% latex dosage, both small and medium pores reached a turning point in their rate of increase. Large pores also exhibited a general increase, peaking at a latex dosage of 10%. It was confirmed that both the total pore volume and the content of micropores were critical factors in determining the mechanical properties of cementitious materials. Higher porosity and micropore content generally weakened mechanical performance. However, at a small latex dosage, there was an improvement in flexural strength. When the latex dosage reached 15%, the total pore and micropore content declined, resulting in a balanced increase in flexural strength and a mitigated decline in compressive strength. This study offers valuable insights into the evolution of total pore volume and the content of pores of various sizes, providing a theoretical basis for the meticulous selection of additive types and dosages from a microscopic perspective.