Keith Sweatman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Keith Sweatman has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Kazuhiro Nogita
Nihon Superior Centre for the Manufacture of Electronic Materials (NS CMEM), School of Mechanical and Mining Engineering, The University of Queensland, St. Lucia, QLD 4072, Australia
4 shared publications - Stuart D. McDonald
School of Mechanical and Mining Engineering, The University of Queensland, St Lucia, QLD 4072, Australia
4 shared publications - Xin Fu Tan
Nihon Superior Centre for the Manufacture of Electronic Materials (NS CMEM), School of Mechanical and Mining Engineering, The University of Queensland, St. Lucia, QLD 4072, Australia
3 shared publications - Christopher M. Gourlay
Department of Materials, Imperial College London, London, UK
2 shared publications - Flora Somidin
Center of Excellence Geopolymer and Green Technology (CEGeoGTech), Faculty of Chemical Engineering & Technology, Universiti Malaysia Perlis (UniMAP), Arau, Malaysia
2 shared publications - Guang Zeng
School of Materials Science and Engineering, Central South University, Changsha, China
2 shared publications
Latest Publications
- Open Access
In Situ Observation of Deformation in a Sn-3Ag-0.5Cu/Cu Solder Joint Using High-Voltage Transmission Electron Microscopy
For reliable electronics, it is important to have an understanding of solder joint failure mechanisms. However, because of difficulties in real-time atomistic scale analysis during deformation, we still do not fully understand these mechanisms. Here, we report on the development of an innovative in situ method of observing the response of the microstructure to tensile strain at room temperature using high-voltage transmission electron microscopy (HV-TEM). This technique was used to observe events including dislocation formation and movement, grain boundary formation and separation, and crack initiation and propagation in a Sn-3 wt.%Ag-0.5 wt.%Cu (SAC305) alloy joint formed between copper substrates.
Open AccessIn Situ Observation of Deformation in a Sn-3Ag-0.5Cu/Cu Solder Joint Using High-Voltage Transmission Electron Microscopy
For reliable electronics, it is important to have an understanding of solder joint failure mechanisms. However, because of difficulties in real-time atomistic scale analysis during deformation, we still do not fully understand these mechanisms. Here, we report on the development of an innovative in situ method of observing the response of the microstructure to tensile strain at room temperature using high-voltage transmission electron microscopy (HV-TEM). This technique was used to observe events including dislocation formation and movement, grain boundary formation and separation, and crack initiation and propagation in a Sn-3 wt.%Ag-0.5 wt.%Cu (SAC305) alloy joint formed between copper substrates.
- Open Access
- 8 July 2025
- Published by MDPI AG in Preprints.org
Dynamic Recrystallisation and Crack Propagation in a Sn-3Ag-0.5Cu/Cu Solder Joint
If electronics manufacturers and users are to have confidence in the reliability of the solder joints on which they rely, it is essential to have an understanding of the solder joint failure mechanisms and the role of dynamic recrystallisation in failure. However, due to difficulties in real-time atomistic scale analysis during deformation, we still do not fully understand these mechanisms. Here, we report the development of an innovative in-situ method using high voltage transmission electron microscopy (HV-TEM) for observation of the microstructural response of a solder joint to room temperature tensile loading. This technique was used to observe events including dislocation formation, dynamic recrystallisation, grain boundary separation, and crack formation and propagation in a Sn-3wt.%Ag-0.5wt.%Cu (SAC305) alloy joint formed between copper substrates.
- 8 July 2025
- Published by MDPI AG in Preprints.org
Open AccessDynamic Recrystallisation and Crack Propagation in a Sn-3Ag-0.5Cu/Cu Solder Joint
If electronics manufacturers and users are to have confidence in the reliability of the solder joints on which they rely, it is essential to have an understanding of the solder joint failure mechanisms and the role of dynamic recrystallisation in failure. However, due to difficulties in real-time atomistic scale analysis during deformation, we still do not fully understand these mechanisms. Here, we report the development of an innovative in-situ method using high voltage transmission electron microscopy (HV-TEM) for observation of the microstructural response of a solder joint to room temperature tensile loading. This technique was used to observe events including dislocation formation, dynamic recrystallisation, grain boundary separation, and crack formation and propagation in a Sn-3wt.%Ag-0.5wt.%Cu (SAC305) alloy joint formed between copper substrates.
- Open Access
- 28 November 2023
- Published by Elsevier in Materialia
- Vol. 33
In-situ investigation of the time-temperature dependent lattice and microstructure of Sn-Bi alloys
- 28 November 2023
- Published by Elsevier in Materialia
- Vol. 33
Open AccessIn-situ investigation of the time-temperature dependent lattice and microstructure of Sn-Bi alloys
- Top Cited PapersOpen Access
Ga-Based Alloys in Microelectronic Interconnects: A Review
Gallium (Ga) and some of its alloys have a range of properties that make them an attractive option for microelectronic interconnects, including low melting point, non-toxicity, and the ability to wet without fluxing most materials—including oxides—found in microelectronics. Some of these properties result from their ability to form stable high melting temperature solid solutions and intermetallic compounds with other metals, such as copper, nickel, and aluminium. Ga and Ga-based alloys have already received significant attention in the scientific literature given their potential for use in the liquid state. Their potential for enabling the miniaturisation and deformability of microelectronic devices has also been demonstrated. The low process temperatures, made possible by their low melting points, produce significant energy savings. However, there are still some issues that need to be addressed before their potential can be fully realised. Characterising Ga and Ga-based alloys, and their reactions with materials commonly used in the microelectronic industry, are thus a priority for the electronics industry. This review provides a summary of research related to the applications and characterisation of Ga-based alloys. If the potential of Ga-based alloys for low temperature bonding in microelectronics manufacturing is to be realised, more work needs to be done on their interactions with the wide range of substrate materials now being used in electronic circuitry.
Top Cited PapersOpen AccessGa-Based Alloys in Microelectronic Interconnects: A Review
Gallium (Ga) and some of its alloys have a range of properties that make them an attractive option for microelectronic interconnects, including low melting point, non-toxicity, and the ability to wet without fluxing most materials—including oxides—found in microelectronics. Some of these properties result from their ability to form stable high melting temperature solid solutions and intermetallic compounds with other metals, such as copper, nickel, and aluminium. Ga and Ga-based alloys have already received significant attention in the scientific literature given their potential for use in the liquid state. Their potential for enabling the miniaturisation and deformability of microelectronic devices has also been demonstrated. The low process temperatures, made possible by their low melting points, produce significant energy savings. However, there are still some issues that need to be addressed before their potential can be fully realised. Characterising Ga and Ga-based alloys, and their reactions with materials commonly used in the microelectronic industry, are thus a priority for the electronics industry. This review provides a summary of research related to the applications and characterisation of Ga-based alloys. If the potential of Ga-based alloys for low temperature bonding in microelectronics manufacturing is to be realised, more work needs to be done on their interactions with the wide range of substrate materials now being used in electronic circuitry.