Aleksy Figurski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aleksy Figurski has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Michał Kowalik
Warsaw University of Technology: Politechnika Warszawska
2 shared publications - Adam Cisowski
Institute of Aeronautics and Applied Mechanics, Warsaw University of Technology, 00-665 Warsaw, Poland
1 shared publication - Dawid Urbanski1 shared publication
- Edyta Ładyżyńska-Kozdraś
Institute of Micromechanics and Photonics, Warsaw University of Technology, Sw. A. Boboli 8, 02-525 Warsaw, Poland
1 shared publication - Erwin Rogoża
Automotive Industry Institute, Łukasiewicz Research Network, Poland
1 shared publication - Jan Tracz
Institute of Aeronautics and Applied Mechanics, Warsaw University of Technology, 00-665 Warsaw, Poland
1 shared publication
Latest Publications
- Open Access
- 9 September 2025
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Journal of Automation, Mobile Robotics and Intelligent Systems
- p. 82-88
A Kinematic Prototype of a Compliant Artificial Prosthetic Knee Joint
This study presents the development and kinematic evaluation of a compliant artificial knee joint prototype fabricated using multi-material 3D printing. The design integrates a rolling-contact compliant mechanism—derived from the CORE and D-CORE concepts—into a prosthetic knee construction, aiming to replicate biological joint behavior while reducing weight, mechanical complexity, and friction. The prototype underwent iterative refinement, including geometric modifications, material selection for flexure bands, and structural asymmetry to mitigate overextension and increase durability. The resulting joint exhibited hybrid kinematic characteristics, blending features of both single-axis and polycentric knee mechanisms, and achieved a functional flexion range of approximately 142 degrees. Initial cyclic tests confirmed satisfactory stiffness and shape recovery of flexure bands with optimized dimensions, although long-term fatigue performance remains a challenge. A basic spring-damper system was also integrated, potentially aligning the prototype with K-1/K-2 prosthetic classification. However, full validation requires further mechanical testing in accordance with ISO 10328 standards, as well as optimization of the damping system for commercial viability. This research demonstrates the feasibility and potential of compliant mechanisms in lower-limb prosthetics while identifying critical areas for future development.
- 9 September 2025
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Journal of Automation, Mobile Robotics and Intelligent Systems
- p. 82-88
Open AccessA Kinematic Prototype of a Compliant Artificial Prosthetic Knee Joint
This study presents the development and kinematic evaluation of a compliant artificial knee joint prototype fabricated using multi-material 3D printing. The design integrates a rolling-contact compliant mechanism—derived from the CORE and D-CORE concepts—into a prosthetic knee construction, aiming to replicate biological joint behavior while reducing weight, mechanical complexity, and friction. The prototype underwent iterative refinement, including geometric modifications, material selection for flexure bands, and structural asymmetry to mitigate overextension and increase durability. The resulting joint exhibited hybrid kinematic characteristics, blending features of both single-axis and polycentric knee mechanisms, and achieved a functional flexion range of approximately 142 degrees. Initial cyclic tests confirmed satisfactory stiffness and shape recovery of flexure bands with optimized dimensions, although long-term fatigue performance remains a challenge. A basic spring-damper system was also integrated, potentially aligning the prototype with K-1/K-2 prosthetic classification. However, full validation requires further mechanical testing in accordance with ISO 10328 standards, as well as optimization of the damping system for commercial viability. This research demonstrates the feasibility and potential of compliant mechanisms in lower-limb prosthetics while identifying critical areas for future development.
- Open Access
- 1 December 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (8) , 46-55
Methodology of Testing for Aluminium Honeycomb Impact Attenuator in Quasi-Static Conditions and Influence of Supporting Structures
This paper examines the influence of two different supports, i.e., composite and steel, on the results obtained during a quasi-static crush test of an aluminum alloy honeycomb impact attenuator. It’s part of a vehicle that competes in the Formula Student series and requires safety tests to be...
- 1 December 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (8) , 46-55
Open AccessMethodology of Testing for Aluminium Honeycomb Impact Attenuator in Quasi-Static Conditions and Influence of Supporting Structures
This paper examines the influence of two different supports, i.e., composite and steel, on the results obtained during a quasi-static crush test of an aluminum alloy honeycomb impact attenuator. It’s part of a vehicle that competes in the Formula Student series and requires safety tests to be...
- Open Access
- 1 December 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (6) , 228-244
Numerical and Experimental Studies on 3D Printed Compliant Mechanisms in Gripper Applications
The article describes two versions of a gripper's fingers that utilize compliant revolute kinematic pairs in their operation. The goal in designing the gripper was to create a universal structure that allows for easy adjustment of torsional stiffness and maximum rotation angle as needed. Two...
- 1 December 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (6) , 228-244
Open AccessNumerical and Experimental Studies on 3D Printed Compliant Mechanisms in Gripper Applications
The article describes two versions of a gripper's fingers that utilize compliant revolute kinematic pairs in their operation. The goal in designing the gripper was to create a universal structure that allows for easy adjustment of torsional stiffness and maximum rotation angle as needed. Two...