Mohamed N. El-Sheikh
Research Subjects
Mohamed N. El-Sheikh has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Ayman Ali Abd-Eltwab
Mechanical engineering department faculty of engineering Beni-Sufe university
4 shared publications - Ahmed M. I. Abu-Oqail2 shared publications
- Emad A. Fahmy
Mechanical Engineering Department Faculty of Engineering Beni-Suef University Beni-Suef 62511 Egypt
2 shared publications - Eman S. M. Abd-Elhalim
Mechanical Eng. Dep., Faculty of Engineering, Assiut University, Assiut, Egypt
2 shared publications - Essam Khalaf Saied2 shared publications
- Hammad T. Elmetwally
Beni-Suef University
2 shared publications
Latest Publications
- Open Access
- 23 December 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (6) , 758-770
Numerical and Experimental Study into forming of the longitudinal Externally Spline Sleeves by internally rotary Ballizing Process
Longitudinal externally splined parts have garnered increasing attention due to their critical role in power transmission across various industrial applications. This study explores the use of the internally rotating balliz-ing technique for manufacturing these components. The process was analyzed both experimentally and numerically through a mathematical model. The experimental investigation focused on key process parameters, including die rotational speed (50, 63, 80, 100, 125, 160, 200, 250, and 315 rpm), axial feed rate (0.13, 0.15, 0.18, and 0.21 mm/rev), interference between the balls and the tubular sample (cross in-feed: 2.5, 3.5, 4.5 and 5.5 mm), and initial tube thickness (4, 5, 6 and 7 mm). The study assessed the influence of these variables on the forming load and the quality of the produced longitudinal externally splined sleeves. A numerical model was developed to predict forming loads, and the findings indicated that these parameters significantly affect both (forming load and filling ratio). The optimal values for these variables were identified, and the numerical results showed a strong correlation with experimental findings.
- 23 December 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (6) , 758-770
Open AccessNumerical and Experimental Study into forming of the longitudinal Externally Spline Sleeves by internally rotary Ballizing Process
Longitudinal externally splined parts have garnered increasing attention due to their critical role in power transmission across various industrial applications. This study explores the use of the internally rotating balliz-ing technique for manufacturing these components. The process was analyzed both experimentally and numerically through a mathematical model. The experimental investigation focused on key process parameters, including die rotational speed (50, 63, 80, 100, 125, 160, 200, 250, and 315 rpm), axial feed rate (0.13, 0.15, 0.18, and 0.21 mm/rev), interference between the balls and the tubular sample (cross in-feed: 2.5, 3.5, 4.5 and 5.5 mm), and initial tube thickness (4, 5, 6 and 7 mm). The study assessed the influence of these variables on the forming load and the quality of the produced longitudinal externally splined sleeves. A numerical model was developed to predict forming loads, and the findings indicated that these parameters significantly affect both (forming load and filling ratio). The optimal values for these variables were identified, and the numerical results showed a strong correlation with experimental findings.
- Open Access
- 11 November 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (4) , 460-468
Novel Multi Levels Tool Based on Rotating Ballizing Technique to Manufacturing the Externally Toothed Components an Experimental Study
Externally toothed components have a very crucial and essential role in all areas of production and manufacturing because they function as away of transmitting motion, energy, and power in all industrial applications, such asmodes of transportation, aviation, aerospace, equipment, and operating machineslike lathes and milling. All machines have a gear box. Therefore, it is receiving increasing attention. This research presents a new multi-stage rotary ballizing technology for producing toothed parts in one stroke. This process has been investigated experimentally. The parameters that were examined experimentally was at the optimal conditions for single stage ballizing were: die rotation speed of 315 rpm; Axial feed rate, 0.13, mm/rev; The interference (cross in-feed) between the balls and the tubular specimen of 5.5 and 6.5 mm is formed by three stages of ball forming of graduated outer diameters and fixed on a single mandrel; Initial tube thickness is 7 and 8 mm. The effect of these parameters on the forming load, filling ratio and quality of the formed part was studied. The finding sindicated that the seideal variables influence the forming load, tooth filling proportion, and product quality. Experimental results proved the success of this novel technique to form toothed tubular components.
- 11 November 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (4) , 460-468
Open AccessNovel Multi Levels Tool Based on Rotating Ballizing Technique to Manufacturing the Externally Toothed Components an Experimental Study
Externally toothed components have a very crucial and essential role in all areas of production and manufacturing because they function as away of transmitting motion, energy, and power in all industrial applications, such asmodes of transportation, aviation, aerospace, equipment, and operating machineslike lathes and milling. All machines have a gear box. Therefore, it is receiving increasing attention. This research presents a new multi-stage rotary ballizing technology for producing toothed parts in one stroke. This process has been investigated experimentally. The parameters that were examined experimentally was at the optimal conditions for single stage ballizing were: die rotation speed of 315 rpm; Axial feed rate, 0.13, mm/rev; The interference (cross in-feed) between the balls and the tubular specimen of 5.5 and 6.5 mm is formed by three stages of ball forming of graduated outer diameters and fixed on a single mandrel; Initial tube thickness is 7 and 8 mm. The effect of these parameters on the forming load, filling ratio and quality of the formed part was studied. The finding sindicated that the seideal variables influence the forming load, tooth filling proportion, and product quality. Experimental results proved the success of this novel technique to form toothed tubular components.
- Open Access
- 1 September 2024
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 24 (4) , 539-551
An Investigation into Forming of Gears Using Rotary Forging Process
Gears and toothed parts are significant components in power transmission systems. These parts usually manufactured by traditional methods such as machining by milling or forming by rotary forging. In this study, the forming of solid gears or toothed parts using a forging process that combines rotary forging and ballizing technique. The specimens were placed inside the die with excessive volume to fill the toothed part in the die. The forming tool applies pressure to the specimen while rotating it together with the die by the lathe machine chuck, while the tool advances continuously in the direction of the die. This reduces height of the specimen and increases its diameter, causing metal flow to fill die cavity teeth and form the gear or toothed part required for production. Two sets of experiments were performed. In the first set, optimization for the appropriate volume of four different sizes of dies and four forming tools was conducted. While in the second set, the effects of forming process variables on the forming load and tooth filling percentage was studied. The results showed that the best tooth filling ratio happened with specimen size of 1.2 to 1.4 times the volume size of the desired tooth for filling. The results also revealed that the forming speed, die size, and forming tool diameter affect the filling ratio and forming load.
- 1 September 2024
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 24 (4) , 539-551
Open AccessAn Investigation into Forming of Gears Using Rotary Forging Process
Gears and toothed parts are significant components in power transmission systems. These parts usually manufactured by traditional methods such as machining by milling or forming by rotary forging. In this study, the forming of solid gears or toothed parts using a forging process that combines rotary forging and ballizing technique. The specimens were placed inside the die with excessive volume to fill the toothed part in the die. The forming tool applies pressure to the specimen while rotating it together with the die by the lathe machine chuck, while the tool advances continuously in the direction of the die. This reduces height of the specimen and increases its diameter, causing metal flow to fill die cavity teeth and form the gear or toothed part required for production. Two sets of experiments were performed. In the first set, optimization for the appropriate volume of four different sizes of dies and four forming tools was conducted. While in the second set, the effects of forming process variables on the forming load and tooth filling percentage was studied. The results showed that the best tooth filling ratio happened with specimen size of 1.2 to 1.4 times the volume size of the desired tooth for filling. The results also revealed that the forming speed, die size, and forming tool diameter affect the filling ratio and forming load.
- Open Access
- 22 December 2023
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 23 (6) , 788-800
An Investigation into Conventional Spinning Process Using Ball Shaped Rollers as Forming Tool
Conventional spinning is one of the oldest processes used widely in manufacturing to obtain cup shape products. Conventional spinning is the technique that produces axisymmetric part or component over rotating mandrel with the help of rigid tool known as rollers. The shape of roller is a very important parameter for the success of the spinning process. The present research is aiming to use ball shaped rollers as forming tools in conventional spinning process experimentally. The experimental work was carried out on the center lathe machine as forming machine, the spinning tool or spinning rollers were installed on a dynamometer replaced the tool post while the mandrel was mounted on the lathe chuck. The spinning tool in this work consists of three rollers performing conventional spinning. The set of rollers is mounted on jaws of lathe chuck which working as a holder for the spinning tool parts. The experimental work was conducted in order to test the proposed tool and investigate the influence of the main conventional spinning parameters (mandrel rotational speed, axial feed and blank diameter or spinning ratio) on the process forming load and the product quality. The response of the product quality and required load to process parameters such as rotational speed (76,150, 230 and 305 rpm), axial feed (0.08, 0.15,0.3, and 0.6 mm/rev) also examined new rollers in different mandrel diameters 45, 60 and 80 mm. The experimental results showed that, the suggested tool acquired a spinning ratio of 2.17 which is about 35% greater than the announced conventional spinning ratio of 1.6 without any addition to the tool just using the suggested Ball shaped roller arrangement. The mandrel rotational speed, and axial feed rate are the most pronounced parameters, which have great effects on the forming loads during the spinning process.
- 22 December 2023
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 23 (6) , 788-800
Open AccessAn Investigation into Conventional Spinning Process Using Ball Shaped Rollers as Forming Tool
Conventional spinning is one of the oldest processes used widely in manufacturing to obtain cup shape products. Conventional spinning is the technique that produces axisymmetric part or component over rotating mandrel with the help of rigid tool known as rollers. The shape of roller is a very important parameter for the success of the spinning process. The present research is aiming to use ball shaped rollers as forming tools in conventional spinning process experimentally. The experimental work was carried out on the center lathe machine as forming machine, the spinning tool or spinning rollers were installed on a dynamometer replaced the tool post while the mandrel was mounted on the lathe chuck. The spinning tool in this work consists of three rollers performing conventional spinning. The set of rollers is mounted on jaws of lathe chuck which working as a holder for the spinning tool parts. The experimental work was conducted in order to test the proposed tool and investigate the influence of the main conventional spinning parameters (mandrel rotational speed, axial feed and blank diameter or spinning ratio) on the process forming load and the product quality. The response of the product quality and required load to process parameters such as rotational speed (76,150, 230 and 305 rpm), axial feed (0.08, 0.15,0.3, and 0.6 mm/rev) also examined new rollers in different mandrel diameters 45, 60 and 80 mm. The experimental results showed that, the suggested tool acquired a spinning ratio of 2.17 which is about 35% greater than the announced conventional spinning ratio of 1.6 without any addition to the tool just using the suggested Ball shaped roller arrangement. The mandrel rotational speed, and axial feed rate are the most pronounced parameters, which have great effects on the forming loads during the spinning process.