Hammad T. Elmetwally
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hammad T. Elmetwally has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Ayman Ali Abd-Eltwab
Mechanical engineering department faculty of engineering Beni-Sufe university
3 shared publications - Mohamed S. Abd-Elhady
Mechanical Engineering Department, Faculty of Engineering, Beni-Suef University, Beni-Suef, Egypt
3 shared publications - Ahmad E. Eladawi
Department of Mechanical Engineering, College of Engineering, Jouf University, Sakaka 42421, Saudi Arabia
2 shared publications - Ahmed M. I. Abu-Oqail2 shared publications
- Emad A. Fahmy
Mechanical Engineering Department Faculty of Engineering Beni-Suef University Beni-Suef 62511 Egypt
2 shared publications - Eman S. M. Abd-Elhalim
Mechanical Eng. Dep., Faculty of Engineering, Assiut University, Assiut, Egypt
2 shared publications
Latest Publications
- Open Access
- 23 December 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (6) , 758-770
Numerical and Experimental Study into forming of the longitudinal Externally Spline Sleeves by internally rotary Ballizing Process
Longitudinal externally splined parts have garnered increasing attention due to their critical role in power transmission across various industrial applications. This study explores the use of the internally rotating balliz-ing technique for manufacturing these components. The process was analyzed both experimentally and numerically through a mathematical model. The experimental investigation focused on key process parameters, including die rotational speed (50, 63, 80, 100, 125, 160, 200, 250, and 315 rpm), axial feed rate (0.13, 0.15, 0.18, and 0.21 mm/rev), interference between the balls and the tubular sample (cross in-feed: 2.5, 3.5, 4.5 and 5.5 mm), and initial tube thickness (4, 5, 6 and 7 mm). The study assessed the influence of these variables on the forming load and the quality of the produced longitudinal externally splined sleeves. A numerical model was developed to predict forming loads, and the findings indicated that these parameters significantly affect both (forming load and filling ratio). The optimal values for these variables were identified, and the numerical results showed a strong correlation with experimental findings.
- 23 December 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (6) , 758-770
Open AccessNumerical and Experimental Study into forming of the longitudinal Externally Spline Sleeves by internally rotary Ballizing Process
Longitudinal externally splined parts have garnered increasing attention due to their critical role in power transmission across various industrial applications. This study explores the use of the internally rotating balliz-ing technique for manufacturing these components. The process was analyzed both experimentally and numerically through a mathematical model. The experimental investigation focused on key process parameters, including die rotational speed (50, 63, 80, 100, 125, 160, 200, 250, and 315 rpm), axial feed rate (0.13, 0.15, 0.18, and 0.21 mm/rev), interference between the balls and the tubular sample (cross in-feed: 2.5, 3.5, 4.5 and 5.5 mm), and initial tube thickness (4, 5, 6 and 7 mm). The study assessed the influence of these variables on the forming load and the quality of the produced longitudinal externally splined sleeves. A numerical model was developed to predict forming loads, and the findings indicated that these parameters significantly affect both (forming load and filling ratio). The optimal values for these variables were identified, and the numerical results showed a strong correlation with experimental findings.
- Open Access
- 11 November 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (4) , 460-468
Novel Multi Levels Tool Based on Rotating Ballizing Technique to Manufacturing the Externally Toothed Components an Experimental Study
Externally toothed components have a very crucial and essential role in all areas of production and manufacturing because they function as away of transmitting motion, energy, and power in all industrial applications, such asmodes of transportation, aviation, aerospace, equipment, and operating machineslike lathes and milling. All machines have a gear box. Therefore, it is receiving increasing attention. This research presents a new multi-stage rotary ballizing technology for producing toothed parts in one stroke. This process has been investigated experimentally. The parameters that were examined experimentally was at the optimal conditions for single stage ballizing were: die rotation speed of 315 rpm; Axial feed rate, 0.13, mm/rev; The interference (cross in-feed) between the balls and the tubular specimen of 5.5 and 6.5 mm is formed by three stages of ball forming of graduated outer diameters and fixed on a single mandrel; Initial tube thickness is 7 and 8 mm. The effect of these parameters on the forming load, filling ratio and quality of the formed part was studied. The finding sindicated that the seideal variables influence the forming load, tooth filling proportion, and product quality. Experimental results proved the success of this novel technique to form toothed tubular components.
- 11 November 2025
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 25 (4) , 460-468
Open AccessNovel Multi Levels Tool Based on Rotating Ballizing Technique to Manufacturing the Externally Toothed Components an Experimental Study
Externally toothed components have a very crucial and essential role in all areas of production and manufacturing because they function as away of transmitting motion, energy, and power in all industrial applications, such asmodes of transportation, aviation, aerospace, equipment, and operating machineslike lathes and milling. All machines have a gear box. Therefore, it is receiving increasing attention. This research presents a new multi-stage rotary ballizing technology for producing toothed parts in one stroke. This process has been investigated experimentally. The parameters that were examined experimentally was at the optimal conditions for single stage ballizing were: die rotation speed of 315 rpm; Axial feed rate, 0.13, mm/rev; The interference (cross in-feed) between the balls and the tubular specimen of 5.5 and 6.5 mm is formed by three stages of ball forming of graduated outer diameters and fixed on a single mandrel; Initial tube thickness is 7 and 8 mm. The effect of these parameters on the forming load, filling ratio and quality of the formed part was studied. The finding sindicated that the seideal variables influence the forming load, tooth filling proportion, and product quality. Experimental results proved the success of this novel technique to form toothed tubular components.
- Open Access
- 22 June 2024
- Published by Mesopotamian Academic Press - DIGITAL COMMONS JOURNALS in Babylonian Journal of Mechanical Engineering
- Vol. 2024, 34-48
Examination of the parameters effect on Al-Cu FSW welded butt joints using formability consent
In most applications, joining aluminum to copper using friction stir welding (FSW) is a primary manufacturing process followed by secondary forming processes. The aim of this study is to investigate the effect of FSW process parameters (speed and feed rate) on the formability of Al-Cu joints. Aluminum and copper blanks were welded at three different rotational speeds, i.e., 910, 1280, and 1700 rpm, and three different feed rates, i.e., 16, 29, and 44 mm/min. The base metals used in this study were aluminum (Al-1050) and copper in two states, i.e., as received and annealed. The mechanical properties of the base metals and the produced compounds were evaluated by tensile and hardness tests. The aluminum-copper joints were drawn into flangeless U-shape and cup shape using FSW to examine the formability of the joints. The maximum tensile load, punch load, and forming index were obtained when Al was at 1700 rpm and 16 mm/min, i.e., h. The welding was performed with annealed copper at the highest rotational speed and lowest feed rate due to work hardening of the joint. However, the ductility was highest at 1280 rpm and 44 mm/min, i.e., at medium rotation and highest travel speed. It can be depicted that when the FSW Al-Cu joint is further used in the forming process, moderate rotation and high feed speed should be adopted for welding to avoid work hardening and improve the ductility of the joint.
- 22 June 2024
- Published by Mesopotamian Academic Press - DIGITAL COMMONS JOURNALS in Babylonian Journal of Mechanical Engineering
- Vol. 2024, 34-48
Open AccessExamination of the parameters effect on Al-Cu FSW welded butt joints using formability consent
In most applications, joining aluminum to copper using friction stir welding (FSW) is a primary manufacturing process followed by secondary forming processes. The aim of this study is to investigate the effect of FSW process parameters (speed and feed rate) on the formability of Al-Cu joints. Aluminum and copper blanks were welded at three different rotational speeds, i.e., 910, 1280, and 1700 rpm, and three different feed rates, i.e., 16, 29, and 44 mm/min. The base metals used in this study were aluminum (Al-1050) and copper in two states, i.e., as received and annealed. The mechanical properties of the base metals and the produced compounds were evaluated by tensile and hardness tests. The aluminum-copper joints were drawn into flangeless U-shape and cup shape using FSW to examine the formability of the joints. The maximum tensile load, punch load, and forming index were obtained when Al was at 1700 rpm and 16 mm/min, i.e., h. The welding was performed with annealed copper at the highest rotational speed and lowest feed rate due to work hardening of the joint. However, the ductility was highest at 1280 rpm and 44 mm/min, i.e., at medium rotation and highest travel speed. It can be depicted that when the FSW Al-Cu joint is further used in the forming process, moderate rotation and high feed speed should be adopted for welding to avoid work hardening and improve the ductility of the joint.
- Open Access
- 1 January 2023
- Published by University Library in Kragujevac in Applied Engineering Letters : Journal of Engineering and Applied Sciences
- Vol. 8 (2) , 60-69
Effect of Friction Stir-Welding Tool Pin Geometry on the Characteristics of Al-Cu Joints
- 1 January 2023
- Published by University Library in Kragujevac in Applied Engineering Letters : Journal of Engineering and Applied Sciences
- Vol. 8 (2) , 60-69
Open AccessEffect of Friction Stir-Welding Tool Pin Geometry on the Characteristics of Al-Cu Joints
- 11 August 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 110 (1-2) , 163-175
Optimum combination of rotational and welding speeds for welding of Al/Cu-butt joint by friction stir welding
- 11 August 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 110 (1-2) , 163-175
Optimum combination of rotational and welding speeds for welding of Al/Cu-butt joint by friction stir welding
- 1 April 2020
- Published by Elsevier in Ceramics International
- Vol. 46 (6) , 7586-7594
Structural, mechanical and tribological properties of Cu–ZrO2/GNPs hybrid nanocomposites
- 1 April 2020
- Published by Elsevier in Ceramics International
- Vol. 46 (6) , 7586-7594
Structural, mechanical and tribological properties of Cu–ZrO2/GNPs hybrid nanocomposites
- 3 November 2017
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 43 (9) , 4433-4441
Improving Heat Transfer Through Paraffin Wax, by Using Fins and Metallic Strips
- 3 November 2017
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 43 (9) , 4433-4441
Improving Heat Transfer Through Paraffin Wax, by Using Fins and Metallic Strips
- Open Access
- 28 May 2017
- Published by David Publishing Company in Journal of Energy and Power Engineering
- Vol. 11 (5)
Prediction of Strain Rate of Aluminum/Silicon Carbide Using Gray Level Run-Length Matrices
- 28 May 2017
- Published by David Publishing Company in Journal of Energy and Power Engineering
- Vol. 11 (5)
Open AccessPrediction of Strain Rate of Aluminum/Silicon Carbide Using Gray Level Run-Length Matrices
- 24 June 2016
- Published by Springer Nature
- p. 33-44
Forming Temperature Investigation of Aluminum and Aluminum/Silicon Carbide Using Image Texture Features
- 24 June 2016
- Published by Springer Nature
- p. 33-44
Forming Temperature Investigation of Aluminum and Aluminum/Silicon Carbide Using Image Texture Features
- 1 April 2015
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 362, 108-114
Statistical Investigation of Maintenance Effects on Quality of Formed Glass Tube Dimensions
Process quality control utilizes inspection of a product while it is being produced through testing periodic samples of products. After this, if product quality characteristics have been changed, the process is stopped, and a search is made for an assignable cause. The objective of a process-capability study is to assess the ability of a process to meet product specifications. During a quality improvement initiative, capability-estimates are obtained at start and at end of study to reflect the occurred improvement. Several capability-estimates show how a process is capable of meeting its specification limits. Essentially, capability-estimates reflect the non conformance rate of a process in a single number form. This involves calculating some ratio of process specification limits. In this study, the production of a fluorescent lamp consisting of a glass tube is considered. Tube quality is affected by the production line conditions. So, the maintenance of the production line is an important stage to increase tube quality. In this paper glass tube quality is studied. Minitab is a statistical software was used to analyze obtained data. The results showed an obvious improvement of part quality after maintenance stage. All measurements were done in Toshiba factory for fluorescent lamp manufacturing.
- 1 April 2015
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 362, 108-114
Statistical Investigation of Maintenance Effects on Quality of Formed Glass Tube Dimensions
Process quality control utilizes inspection of a product while it is being produced through testing periodic samples of products. After this, if product quality characteristics have been changed, the process is stopped, and a search is made for an assignable cause. The objective of a process-capability study is to assess the ability of a process to meet product specifications. During a quality improvement initiative, capability-estimates are obtained at start and at end of study to reflect the occurred improvement. Several capability-estimates show how a process is capable of meeting its specification limits. Essentially, capability-estimates reflect the non conformance rate of a process in a single number form. This involves calculating some ratio of process specification limits. In this study, the production of a fluorescent lamp consisting of a glass tube is considered. Tube quality is affected by the production line conditions. So, the maintenance of the production line is an important stage to increase tube quality. In this paper glass tube quality is studied. Minitab is a statistical software was used to analyze obtained data. The results showed an obvious improvement of part quality after maintenance stage. All measurements were done in Toshiba factory for fluorescent lamp manufacturing.