Yaqiang Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yaqiang Wang has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Qingjin Xu
Chinese Academy of Sciences
7 shared publications - Chengtao Wang
Accelerator Division, Institute of High Energy Physics Chinese Academy of Sciences, Beijing, CHINA
6 shared publications - Xin Chen
Institute of High Energy Physics (IHEP), Chinese Academy of Sciences (CAS), Beijing, China
6 shared publications - Hongjun Zhang
Laboratory of Particle Acceleration Physics and Technology, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, China
5 shared publications - Jinrui Shi
Laboratory of Particle Acceleration Physics and Technology, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, China
5 shared publications - Rui Kang
Institute of High Energy Physics Chinese Academy of Sciences, Beijing, China
5 shared publications
Latest Publications
- 20 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Conceptual Design Study of a Superconducting Flywheel System With Enhanced Speed Using Dipole Field
The high temperature superconductivity (HTS) technology present itself a bright future to be used in a flywheel energy storage system (FESS). In addition to the characteristics of conventional flywheel energy storage systems, the self-stability of high temperature superconducting maglev enables the suspension bearing to completely eliminate external control, improving the efficiency and stability of the whole system. And superconducting flywheel energy storage system can effectively eliminate the loss caused by mechanical friction and the electrical loss caused by resistance. In this paper, a superconducting flywheel system which is suspended and self-stabilized through the meticulous design of a high magnetic field is presented. The most obvious advantages are the reduction of mechanical friction, the use of Lorentz force to provide centripetal force instead of relying on mechanical limit of materials, and a higher speed than traditional flywheels. The optimization of the field distribution as well as the HTS coil of the flywheel is discussed. Subsequently, the energy storage efficiency, power density, energy ratio and suspension force of the flywheel are analyzed and compared in detail.
- 20 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Conceptual Design Study of a Superconducting Flywheel System With Enhanced Speed Using Dipole Field
The high temperature superconductivity (HTS) technology present itself a bright future to be used in a flywheel energy storage system (FESS). In addition to the characteristics of conventional flywheel energy storage systems, the self-stability of high temperature superconducting maglev enables the suspension bearing to completely eliminate external control, improving the efficiency and stability of the whole system. And superconducting flywheel energy storage system can effectively eliminate the loss caused by mechanical friction and the electrical loss caused by resistance. In this paper, a superconducting flywheel system which is suspended and self-stabilized through the meticulous design of a high magnetic field is presented. The most obvious advantages are the reduction of mechanical friction, the use of Lorentz force to provide centripetal force instead of relying on mechanical limit of materials, and a higher speed than traditional flywheels. The optimization of the field distribution as well as the HTS coil of the flywheel is discussed. Subsequently, the energy storage efficiency, power density, energy ratio and suspension force of the flywheel are analyzed and compared in detail.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Numerical Simulation of the Mechanical Behavior of a Transposed Cable With the In-Plane Bending of ReBCO Tapes
The Institute of High Energy Physics, Chinese Academy of Sciences (IEHP, CAS) proposed a compact ReBCO cable (named X-cable) which is implemented by in-plane bending ReBCO tapes to realize the transposition, and successfully fabricated a 10 m length prototype cable. The study on the mechanical properties of the cable is of great significance to its engineering application. Based on the finite element model, the stress-strain state of cable under different loads has been analyzed, which are used to predict the critical current performance of superconducting tapes in cable. This paper focuses on the possible failure mechanism of the X-cable under bending and transverse loads. Based on the established model, the critical bending radius of the x-cable is determined to be 20 mm. We analyzed the critical pressure and shear stress of the cable under lateral load, considering two possible scenarios that may occur during the manufacturing process. The above results can serve as a valuable reference for subsequent design of magnets and winding of coils.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Numerical Simulation of the Mechanical Behavior of a Transposed Cable With the In-Plane Bending of ReBCO Tapes
The Institute of High Energy Physics, Chinese Academy of Sciences (IEHP, CAS) proposed a compact ReBCO cable (named X-cable) which is implemented by in-plane bending ReBCO tapes to realize the transposition, and successfully fabricated a 10 m length prototype cable. The study on the mechanical properties of the cable is of great significance to its engineering application. Based on the finite element model, the stress-strain state of cable under different loads has been analyzed, which are used to predict the critical current performance of superconducting tapes in cable. This paper focuses on the possible failure mechanism of the X-cable under bending and transverse loads. Based on the established model, the critical bending radius of the x-cable is determined to be 20 mm. We analyzed the critical pressure and shear stress of the cable under lateral load, considering two possible scenarios that may occur during the manufacturing process. The above results can serve as a valuable reference for subsequent design of magnets and winding of coils.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (4) , 1-9
A Novel Aluminum-Stabilized Stacked REBCO Tape Cable
In the new concept design of the circular electron positron collider detector, the magnet should be an ultrathin HTS solenoid with maximum radiation transparency. A novel aluminum-stabilized stacked REBCO tape cable (ASTC) was proposed and developed. The advantages of aluminum's high residual resistivity ratio, high thermal conductivity, and high transparency for particles, combined with the advantages of REBCO tape's high engineering current density, high strength and large temperature margin, constitute a suitable cable option for future detector magnets. The ASTC uses REBCO tapes in a stacked structure, which are wrapped and bound with metal tapes, and then covered with aluminum stabilizer by coextrusion processing. By optimizing the process parameters, such as preheating temperature, extrusion speed, Al outer layer thickness, and improving the internal structure of the cable, the critical current of the ASTC prototype cable is increased to 905 A@ 77 K, self-field. The degradation of the tape is less than 20%. This article presents the development process of the ASTC cable, discusses the challenges encountered during cable processing, and proposes corresponding solutions.
- 6 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (4) , 1-9
A Novel Aluminum-Stabilized Stacked REBCO Tape Cable
In the new concept design of the circular electron positron collider detector, the magnet should be an ultrathin HTS solenoid with maximum radiation transparency. A novel aluminum-stabilized stacked REBCO tape cable (ASTC) was proposed and developed. The advantages of aluminum's high residual resistivity ratio, high thermal conductivity, and high transparency for particles, combined with the advantages of REBCO tape's high engineering current density, high strength and large temperature margin, constitute a suitable cable option for future detector magnets. The ASTC uses REBCO tapes in a stacked structure, which are wrapped and bound with metal tapes, and then covered with aluminum stabilizer by coextrusion processing. By optimizing the process parameters, such as preheating temperature, extrusion speed, Al outer layer thickness, and improving the internal structure of the cable, the critical current of the ASTC prototype cable is increased to 905 A@ 77 K, self-field. The degradation of the tape is less than 20%. This article presents the development process of the ASTC cable, discusses the challenges encountered during cable processing, and proposes corresponding solutions.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Bending Characteristics of a Transposed Cable (X-Cable) With in-Plane Bending of REBCO Tapes
A compact High Temperature Superconducting (HTS) cable, which is achieved by in-plane bending stacked REBCO tapes directly to realize the transposition(X-cable), has been designed and successfully fabricated by the Institute of High Energy Physics, Chinese Academy of Sciences (IHEP, CAS) for the application in high-field accelerator magnets. The high current carrying capacity and low AC loss of the X-cable have been investigated in our previous studies. In this article, the bendability of the X-cable was studied at 77 K and self-field, especially the minimum bending radius without performance degradation. The critical current ( I c ) of each tape contained in the full-scale strand in the cable was powered individually at different bending radii. By analyzing the single tape's Ic as a function of bending radius, the test results demonstrate a good bending performance of the cable. The inter-tape resistance ( Rc ) is also investigated as a function of bending radius, which becomes more uniform and smaller after bending. Meanwhile, the dome-like shape of Rc explains that the copper film wrapped outside the stack can help share the current to improve the stability of the cable. The cable's parameters, bending performance test, and results analysis are presented in this work.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Bending Characteristics of a Transposed Cable (X-Cable) With in-Plane Bending of REBCO Tapes
A compact High Temperature Superconducting (HTS) cable, which is achieved by in-plane bending stacked REBCO tapes directly to realize the transposition(X-cable), has been designed and successfully fabricated by the Institute of High Energy Physics, Chinese Academy of Sciences (IHEP, CAS) for the application in high-field accelerator magnets. The high current carrying capacity and low AC loss of the X-cable have been investigated in our previous studies. In this article, the bendability of the X-cable was studied at 77 K and self-field, especially the minimum bending radius without performance degradation. The critical current ( I c ) of each tape contained in the full-scale strand in the cable was powered individually at different bending radii. By analyzing the single tape's Ic as a function of bending radius, the test results demonstrate a good bending performance of the cable. The inter-tape resistance ( Rc ) is also investigated as a function of bending radius, which becomes more uniform and smaller after bending. Meanwhile, the dome-like shape of Rc explains that the copper film wrapped outside the stack can help share the current to improve the stability of the cable. The cable's parameters, bending performance test, and results analysis are presented in this work.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design, Simulation and Test Results of Quench Protection System for a 13-T Twin-Aperture Superconducting Dipole Magnet
On the basis of the successful development of a high field dipole magnet named LPF1-U, which reached a peak field of 12.47 T in 2021, the new magnet LPF3 with an expected field of over 13 T in the two 50-mm apertures has been designed and fabricated at IHEP. The magnet is developed in a common-coil configuration with six flat racetrack Nb 3 Sn coils, as well as High Temperature Superconducting (HTS) insert coils in the center to further enhance the field to 16 T or more. The Nb 3 Sn coils are designed to provide a 13 T main field at the operating current of 7580 A. The quench protection of the Nb 3 Sn coils is significantly important and challenging because of the much larger magnet apertures (50 mm) and stored energy (2155 kJ). Finally, the method of CLIQ (coupling-loss induced quench protection system) together with varistor is adopted to accelerate the propagation of quench in the magnet and control the hotspot temperature. This article describes the design of the optimized quench protection scheme, the model and the simulation results. The experiment test results are also analyzed and discussed in this article.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design, Simulation and Test Results of Quench Protection System for a 13-T Twin-Aperture Superconducting Dipole Magnet
On the basis of the successful development of a high field dipole magnet named LPF1-U, which reached a peak field of 12.47 T in 2021, the new magnet LPF3 with an expected field of over 13 T in the two 50-mm apertures has been designed and fabricated at IHEP. The magnet is developed in a common-coil configuration with six flat racetrack Nb 3 Sn coils, as well as High Temperature Superconducting (HTS) insert coils in the center to further enhance the field to 16 T or more. The Nb 3 Sn coils are designed to provide a 13 T main field at the operating current of 7580 A. The quench protection of the Nb 3 Sn coils is significantly important and challenging because of the much larger magnet apertures (50 mm) and stored energy (2155 kJ). Finally, the method of CLIQ (coupling-loss induced quench protection system) together with varistor is adopted to accelerate the propagation of quench in the magnet and control the hotspot temperature. This article describes the design of the optimized quench protection scheme, the model and the simulation results. The experiment test results are also analyzed and discussed in this article.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Numerical and Experimental Analysis of Thermomagnetic Instability in Nb3Sn Wires
Nb 3 Sn is now recognized as the practical material for the high-field applications from 10 to 16 T, for particle accelerators, fusion and other related fields. However, the obtaining of high J c in Nb 3 Sn presently contradicts one of the most important stability criteria: to keep a small filament size, which makes the stability issue particularly prominent. Large filament sizes frequently cause flux jumps in the conductor, making quench detection and protection more challenging for Nb 3 Sn magnets. In this work, we try to numerically simulate the flux jumps more accurately down to a filamentary scale. Based on the theory of superconducting dynamics, we have established a theoretical model to describe the magnetothermal instability of Nb 3 Sn wires by considering the superconductor flux dynamics, heat diffusion and temperature response. The preliminary analysis of the test results for LPF3 which is a 16-T hybrid common coil dipole magnet fabricated by Institute of High Energy Physics is conducted to study the causes of its quenching and the impact of flux jumps on the magnet.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Numerical and Experimental Analysis of Thermomagnetic Instability in Nb3Sn Wires
Nb 3 Sn is now recognized as the practical material for the high-field applications from 10 to 16 T, for particle accelerators, fusion and other related fields. However, the obtaining of high J c in Nb 3 Sn presently contradicts one of the most important stability criteria: to keep a small filament size, which makes the stability issue particularly prominent. Large filament sizes frequently cause flux jumps in the conductor, making quench detection and protection more challenging for Nb 3 Sn magnets. In this work, we try to numerically simulate the flux jumps more accurately down to a filamentary scale. Based on the theory of superconducting dynamics, we have established a theoretical model to describe the magnetothermal instability of Nb 3 Sn wires by considering the superconductor flux dynamics, heat diffusion and temperature response. The preliminary analysis of the test results for LPF3 which is a 16-T hybrid common coil dipole magnet fabricated by Institute of High Energy Physics is conducted to study the causes of its quenching and the impact of flux jumps on the magnet.
- 25 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet With Graded Common-Coil Configuration
R&D of high field accelerator magnets is ongoing at the Institute of High Energy Physics, Chinese Academy of Sciences (IHEP, CAS) for pre-study of the next-generation high energy colliders like Super Proton-Proton Collider (SPPC), Future Circular Collider (FCC) and etc. A 12.47-T main field at 4.2 K has been attained in 2021 within two 14-mm apertures of LPF1-U, a superconducting model dipole magnet with Nb 3 Sn & NbTi combined common-coil configuration. Based on the experiences mastered in the LPF1 series magnets, a 16-T high field dipole magnet named LPF3 has been designed, fabricated and is in the performance test process. LPF3 is also a combined magnet with six racetrack Nb 3 Sn coils outside, expected to provide a 13-T main field within two 50-mm apertures, and with inserted HTS coils to enhance the field up to 16 T or even higher. The 13-T Nb 3 Sn dipole magnet, named LPF3-LTS, incorporates a graded common-coil configuration to enhance superconductor efficiency. The optimization of coil layouts includes varying bending radii (BR) and lengths of straight sections (LSS) to mitigate field accumulation in the outer four coils near the central posts and coil ends, respectively. Several Rutherford cables over 200 meters were fabricated for the coils winding, and with the maximum strands count of 42. The support structure for LPF3-LTS has adopted a shell-based design, with an improved “Bladder & Key” technology. Dedicated hydraulic pistons were investigated and utilized to replace the traditional bladders. The main design characteristics, fabrication process and some preliminary test results of the magnet are presented in this paper.
- 25 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet With Graded Common-Coil Configuration
R&D of high field accelerator magnets is ongoing at the Institute of High Energy Physics, Chinese Academy of Sciences (IHEP, CAS) for pre-study of the next-generation high energy colliders like Super Proton-Proton Collider (SPPC), Future Circular Collider (FCC) and etc. A 12.47-T main field at 4.2 K has been attained in 2021 within two 14-mm apertures of LPF1-U, a superconducting model dipole magnet with Nb 3 Sn & NbTi combined common-coil configuration. Based on the experiences mastered in the LPF1 series magnets, a 16-T high field dipole magnet named LPF3 has been designed, fabricated and is in the performance test process. LPF3 is also a combined magnet with six racetrack Nb 3 Sn coils outside, expected to provide a 13-T main field within two 50-mm apertures, and with inserted HTS coils to enhance the field up to 16 T or even higher. The 13-T Nb 3 Sn dipole magnet, named LPF3-LTS, incorporates a graded common-coil configuration to enhance superconductor efficiency. The optimization of coil layouts includes varying bending radii (BR) and lengths of straight sections (LSS) to mitigate field accumulation in the outer four coils near the central posts and coil ends, respectively. Several Rutherford cables over 200 meters were fabricated for the coils winding, and with the maximum strands count of 42. The support structure for LPF3-LTS has adopted a shell-based design, with an improved “Bladder & Key” technology. Dedicated hydraulic pistons were investigated and utilized to replace the traditional bladders. The main design characteristics, fabrication process and some preliminary test results of the magnet are presented in this paper.
- 15 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 806-813
Strategies for the PAMS Control of Module-Combined DC/DC Converters Available for All-DC Wind Farms
All-DC wind farms employing DC convergence and transmission obviate the requirement for large industrial AC transformers. This approach confers notable benefits in power density, construction cost, and system efficiency. A module-combined DC/DC converter is ideal for transmitting power generated by all-DC wind farms. Nevertheless, throughout the aggregation process, the output power of the wind turbine and the transmission power of the converter fluctuate in response to changing wind speeds. Substantial power losses occur in the module-combined DC/DC converter when wind speeds drop below the rated threshold, as all sub-modules receive maximum inputs. Hence, based on the wind turbine's power output characteristics, we introduce the Power Approximation for Module Shedding (PAMS) technique tailored to the module-combined DC/DC converter. PAMS aims to minimize power losses and enhance transmission efficiency in the converter. This is achieved by dynamically adjusting the number of sub-modules during the aggregation process to match the real-time wind turbine output power, thereby improving overall converter efficiency. Lastly, we validate the feasibility and effectiveness of the PAMS control method through simulation using MATLAB/Simulink.
- 15 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 806-813
Strategies for the PAMS Control of Module-Combined DC/DC Converters Available for All-DC Wind Farms
All-DC wind farms employing DC convergence and transmission obviate the requirement for large industrial AC transformers. This approach confers notable benefits in power density, construction cost, and system efficiency. A module-combined DC/DC converter is ideal for transmitting power generated by all-DC wind farms. Nevertheless, throughout the aggregation process, the output power of the wind turbine and the transmission power of the converter fluctuate in response to changing wind speeds. Substantial power losses occur in the module-combined DC/DC converter when wind speeds drop below the rated threshold, as all sub-modules receive maximum inputs. Hence, based on the wind turbine's power output characteristics, we introduce the Power Approximation for Module Shedding (PAMS) technique tailored to the module-combined DC/DC converter. PAMS aims to minimize power losses and enhance transmission efficiency in the converter. This is achieved by dynamically adjusting the number of sub-modules during the aggregation process to match the real-time wind turbine output power, thereby improving overall converter efficiency. Lastly, we validate the feasibility and effectiveness of the PAMS control method through simulation using MATLAB/Simulink.
- 1 January 2002
- Published by ASME International
- p. 103-109
Fabrication and Characterization of Evanescent Microwave Probes Compatible With Atomic Force Microscope for Scanning Near-Field Microscopy
The design and microfabrication of silicon co-axial evanescent microwave probes (EMP) compatible with atomic force microscope (AFM) imaging was discussed. Scanning EMP (SEMP) imaging is suitable for nondestructive surface and subsurface characterization of materials over a wide frequency range-between 0.1 GHz and 140 GHz. The microfabricated EMP consists of a silicon V-shaped cantilever beam, a co-axial tip, and aluminum co-planar waveguides. The coaxial tip has an apex radius of ∼80 Å. The tip itself is oxidation-sharpened heavily-doped silicon surrounded by an oxide layer that acts as insulator and covered with an aluminum co-axial layer. The tip apex is electrically connected to a strip of aluminum that forms the active part of the waveguide. The design and microfabrication procedure are described. Mechanical and electrical characterizations are discussed. Contact mode and SEMP surface measurement results are reported. The first ever simultaneous contact AFM and scanning near-field microwave microscopy (SNMM) surface imaging are presented. Using the microwave measurement along with the AFM imaging opens up a new window to see inside the materials and sets the stage for hyperspectral imaging of organelles of biological objects as well as electronic devices and structural materials.
- 1 January 2002
- Published by ASME International
- p. 103-109
Fabrication and Characterization of Evanescent Microwave Probes Compatible With Atomic Force Microscope for Scanning Near-Field Microscopy
The design and microfabrication of silicon co-axial evanescent microwave probes (EMP) compatible with atomic force microscope (AFM) imaging was discussed. Scanning EMP (SEMP) imaging is suitable for nondestructive surface and subsurface characterization of materials over a wide frequency range-between 0.1 GHz and 140 GHz. The microfabricated EMP consists of a silicon V-shaped cantilever beam, a co-axial tip, and aluminum co-planar waveguides. The coaxial tip has an apex radius of ∼80 Å. The tip itself is oxidation-sharpened heavily-doped silicon surrounded by an oxide layer that acts as insulator and covered with an aluminum co-axial layer. The tip apex is electrically connected to a strip of aluminum that forms the active part of the waveguide. The design and microfabrication procedure are described. Mechanical and electrical characterizations are discussed. Contact mode and SEMP surface measurement results are reported. The first ever simultaneous contact AFM and scanning near-field microwave microscopy (SNMM) surface imaging are presented. Using the microwave measurement along with the AFM imaging opens up a new window to see inside the materials and sets the stage for hyperspectral imaging of organelles of biological objects as well as electronic devices and structural materials.