Dan Kuylenstierna
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dan Kuylenstierna has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
David Larsson
Chalmers University of Technology
1 shared publication- Herbert Zirath
Chalmers University of Technology
1 shared publication Julia Ortheden
Chalmers University of Technology
1 shared publication- Markus Pettersson
Chalmers University of Technology
1 shared publication - Mikael Horberg
Antenna and Hardware Research Center, Ericsson Research, Ericsson AB, Gothenburg, Sweden
1 shared publication - Qazi Mashaal Khan
Department of Electrical and Electronic Engineering, ESEO School of Engineering, Angers, France
1 shared publication
Latest Publications
- 16 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Multiscale and Multiphysics Computational Techniques
- Vol. 9, 75-83
Analysis of Q-Factor for AM-SLM Cavity Based Resonators Using Surface Roughness Models
This research delves into losses of X-band cavity resonators manufactured using additive manufacturing-selective laser melting (AM-SLM) compared to the standard subtractive manufacturing milling technology. Measured losses are benchmarked in terms of resonator (quality) $Q$ -factor. The measured data is further modelled using the Groiss and one-ball Huray models taking into account the implications of surface roughness and electrical conductivity. The unloaded $Q$ -factor is derived from frequency-dependent scattering ( $S$ ) parameters obtained from measurements and full-wave simulations. Surface roughness was found to impact the $Q$ -factor significantly and the resonant frequency marginally. Cavities based on AM-SLM technology exhibit higher roughness compared to milling and lowers the $Q$ -factor. A fusion of both manufacturing methods by milling AM-SLM cavity walls demonstrates an augmented $Q$ -factor compared to a directly printed cavity. In the study it was also found that the Groiss model tends to overestimate the $Q$ -factor owing to AM-SLM's rougher surface, while the one-ball Huray model furnishes precise projections by establishing a link between surface roughness and powder particles. Electrical conductivity's influence on $Q$ -factor was also investigated, showing negligible impact with increased surface roughness. Further, side walls of the AM-SLM cavity were more susceptible to surface roughness, compared to the cavity front walls due to higher surface current density. This study underscores the significance of analyzing surface roughness and electrical conductivity in AM-SLM cavity resonators and highlights the suitability of the one-ball Huray model for accurate $Q$ -factor prediction of microwave structures with rough surfaces.
- 16 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Multiscale and Multiphysics Computational Techniques
- Vol. 9, 75-83
Analysis of Q-Factor for AM-SLM Cavity Based Resonators Using Surface Roughness Models
This research delves into losses of X-band cavity resonators manufactured using additive manufacturing-selective laser melting (AM-SLM) compared to the standard subtractive manufacturing milling technology. Measured losses are benchmarked in terms of resonator (quality) $Q$ -factor. The measured data is further modelled using the Groiss and one-ball Huray models taking into account the implications of surface roughness and electrical conductivity. The unloaded $Q$ -factor is derived from frequency-dependent scattering ( $S$ ) parameters obtained from measurements and full-wave simulations. Surface roughness was found to impact the $Q$ -factor significantly and the resonant frequency marginally. Cavities based on AM-SLM technology exhibit higher roughness compared to milling and lowers the $Q$ -factor. A fusion of both manufacturing methods by milling AM-SLM cavity walls demonstrates an augmented $Q$ -factor compared to a directly printed cavity. In the study it was also found that the Groiss model tends to overestimate the $Q$ -factor owing to AM-SLM's rougher surface, while the one-ball Huray model furnishes precise projections by establishing a link between surface roughness and powder particles. Electrical conductivity's influence on $Q$ -factor was also investigated, showing negligible impact with increased surface roughness. Further, side walls of the AM-SLM cavity were more susceptible to surface roughness, compared to the cavity front walls due to higher surface current density. This study underscores the significance of analyzing surface roughness and electrical conductivity in AM-SLM cavity resonators and highlights the suitability of the one-ball Huray model for accurate $Q$ -factor prediction of microwave structures with rough surfaces.
- 10 April 2022
- Published by Springer Nature
- p. 126-129
Machine Learning Techniques for Gait Analysis in Skiing
- 10 April 2022
- Published by Springer Nature
- p. 126-129
Machine Learning Techniques for Gait Analysis in Skiing
- 3 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 65 (9) , 3257-3268
Analysis of a MEMS Tuned Cavity Oscillator on $X$ -BandThis paper reports on the analysis of a radio frequency microelectromechanical systems (RF-MEMS) tuned cavity oscillator on X-band based on a GaN-HEMT monolithic microwave integrated circuit reflection amplifier. The RF-MEMS-switches are mounted on a low-loss printed circuit board (PCB) intruded in an aluminum cavity that is coupled to a microstrip line connected to the reflection amplifier. This paper investigates the influence of the number of switches as well as their positions with respect to phase noise and tuning range. Vertical and horizontal positions of the switches are varied with target on optimum trade-off between phase noise and total tuning range. For a three-row MEMS-configuration at 1-mm depth from the end cavity wall, a tuning range of 4.9% is measured. The center frequencies are ranging from 9.84 to 10.33 GHz with measured phase noise of -140 to -129 dBc/Hz at 100-kHz offset. A similar three-row MEMS setup at 2.5-mm depth provides a tuning range of 12.3% with measured phase noise of -133 to -123 dBc/Hz at 100-kHz offset.
- 3 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 65 (9) , 3257-3268
Analysis of a MEMS Tuned Cavity Oscillator on $X$ -BandThis paper reports on the analysis of a radio frequency microelectromechanical systems (RF-MEMS) tuned cavity oscillator on X-band based on a GaN-HEMT monolithic microwave integrated circuit reflection amplifier. The RF-MEMS-switches are mounted on a low-loss printed circuit board (PCB) intruded in an aluminum cavity that is coupled to a microstrip line connected to the reflection amplifier. This paper investigates the influence of the number of switches as well as their positions with respect to phase noise and tuning range. Vertical and horizontal positions of the switches are varied with target on optimum trade-off between phase noise and total tuning range. For a three-row MEMS-configuration at 1-mm depth from the end cavity wall, a tuning range of 4.9% is measured. The center frequencies are ranging from 9.84 to 10.33 GHz with measured phase noise of -140 to -129 dBc/Hz at 100-kHz offset. A similar three-row MEMS setup at 2.5-mm depth provides a tuning range of 12.3% with measured phase noise of -133 to -123 dBc/Hz at 100-kHz offset.