Darius Hoffmeister
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Darius Hoffmeister has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Andreas Hutzler
Helmholtz Institute Erlangen‐Nürnberg for Renewable Energy (IET‐2) Forschungszentrum Jülich GmbH Erlangen Germany
10 shared publications - Simon Thiele
Forschungszentrum Jülich GmbH, HI ERN (IEK-11)
9 shared publications - Erdmann Spiecker
Institute of Micro‐ and Nanostructure Research and Center for Nanoanalysis and Electron Microscopy (CENEM) IZNF Friedrich‐Alexander‐Universität Erlangen‐Nürnberg Erlangen Germany
8 shared publications - Selina Finger
Helmholtz Institute Erlangen-Nürnberg for Renewable Energy (IET-2), Forschungszentrum Jülich GmbH, 91058 Erlangen, Germany
6 shared publications - Tien-Ching Ma
Forschungszentrum Jülich
6 shared publications - Anna Teressa Sophie Freiberg
Helmholtz-Institute Erlangen-Nürnberg for Renewable Energy (IET-2), Forschungszentrum Jülich GmbH , Cauerstr. 1
5 shared publications
Latest Publications
- Open Access
- 15 June 2026
- Published by Wiley in Energy & Environmental Materials
Revealing Structure–Performance Relations in Core‐Shell Catalyst‐Based PEM Water Electrolyzer Anodes with Low Iridium Loading
Reducing iridium loading in proton exchange membrane water electrolyzer anodes is essential to meet cost targets for large‐scale green hydrogen production. Here, we report a photodeposition‐based synthesis of TiO 2 @IrO 2 core‐shell catalysts with iridium contents as low as 10 wt%. The influence of annealing temperature, iridium content, and iridium loading on structural and electrochemical properties is systematically investigated. An annealing temperature of 450 °C provides the best compromise between activity, conductivity, and stability. Remarkably, even at 10 wt% Ir (≈4.5 vol% IrO 2 ), the core‐shell architecture maintains high electronic conductivity and mass activity. The low iridium content results in ~18 μm thick catalyst layers at a loading of 0.35 mg Ir cm −2 , corresponding to a high thickness factor of 52.0 ± 0.8 μm (mg Ir cm −2 ) −1 . Two‐dimensional, two‐phase performance modeling reveals that these thick catalyst layers improve electronic connectivity at low loadings, leading to higher catalyst utilization than a commercial reference. As a result, the core‐shell catalyst outperforms the reference in single‐cell measurements, achieving 1.77 V at 2 A cm −2 at a low loading of 0.31 mg Ir cm −2 . During 200 h durability testing, reversible degradation is observed, while irreversible losses remain on par with the reference and the core–shell structure is preserved.
- 15 June 2026
- Published by Wiley in Energy & Environmental Materials
Open AccessRevealing Structure–Performance Relations in Core‐Shell Catalyst‐Based PEM Water Electrolyzer Anodes with Low Iridium Loading
Reducing iridium loading in proton exchange membrane water electrolyzer anodes is essential to meet cost targets for large‐scale green hydrogen production. Here, we report a photodeposition‐based synthesis of TiO 2 @IrO 2 core‐shell catalysts with iridium contents as low as 10 wt%. The influence of annealing temperature, iridium content, and iridium loading on structural and electrochemical properties is systematically investigated. An annealing temperature of 450 °C provides the best compromise between activity, conductivity, and stability. Remarkably, even at 10 wt% Ir (≈4.5 vol% IrO 2 ), the core‐shell architecture maintains high electronic conductivity and mass activity. The low iridium content results in ~18 μm thick catalyst layers at a loading of 0.35 mg Ir cm −2 , corresponding to a high thickness factor of 52.0 ± 0.8 μm (mg Ir cm −2 ) −1 . Two‐dimensional, two‐phase performance modeling reveals that these thick catalyst layers improve electronic connectivity at low loadings, leading to higher catalyst utilization than a commercial reference. As a result, the core‐shell catalyst outperforms the reference in single‐cell measurements, achieving 1.77 V at 2 A cm −2 at a low loading of 0.31 mg Ir cm −2 . During 200 h durability testing, reversible degradation is observed, while irreversible losses remain on par with the reference and the core–shell structure is preserved.
- Open Access
- 30 March 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Revealing Structure-Performance Relations in Core-Shell Catalyst Based PEM Water Electrolyzer Anodes with Low Iridium Loading
Reducing iridium loading in proton exchange membrane water electrolyzer anodes is essential to meet cost targets for large-scale green hydrogen production. Here, we report a photodeposition-based synthesis of TiO 2 @IrO 2 core-shell catalysts with iridium contents as low as 10 wt%. The influence of annealing temperature, iridium content, and iridium loading on structural and electrochemical properties is systematically investigated. An annealing temperature of 450 °C provides the best compromise between activity, conductivity, and stability. Remarkably, even at 10 wt% Ir (≈ 4.5 vol% IrO 2 ), the core-shell architecture maintains high electronic conductivity and mass activity. The low iridium content results in ~18 µm thick catalyst layers at a loading of 0.35 mg Ir cm ‑2 , corresponding to a high thickness factor of 52.0 ± 0.8 µm (mg Ir cm ‑2 ) ‑1 . Two-dimensional, two‑phase performance modeling reveals that these thick catalyst layers improve electronic connectivity at low loadings, leading to higher catalyst utilization than a commercial reference. As a result, the core-shell catalyst outperforms the reference in single-cell measurements, achieving 1.77 V at 2 A cm ‑2 at a low loading of 0.31 mg Ir cm ‑2 . During 200 h durability testing, reversible degradation is observed, while irreversible losses remain on par with the reference and the core–shell structure is preserved.
- 30 March 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessRevealing Structure-Performance Relations in Core-Shell Catalyst Based PEM Water Electrolyzer Anodes with Low Iridium Loading
Reducing iridium loading in proton exchange membrane water electrolyzer anodes is essential to meet cost targets for large-scale green hydrogen production. Here, we report a photodeposition-based synthesis of TiO 2 @IrO 2 core-shell catalysts with iridium contents as low as 10 wt%. The influence of annealing temperature, iridium content, and iridium loading on structural and electrochemical properties is systematically investigated. An annealing temperature of 450 °C provides the best compromise between activity, conductivity, and stability. Remarkably, even at 10 wt% Ir (≈ 4.5 vol% IrO 2 ), the core-shell architecture maintains high electronic conductivity and mass activity. The low iridium content results in ~18 µm thick catalyst layers at a loading of 0.35 mg Ir cm ‑2 , corresponding to a high thickness factor of 52.0 ± 0.8 µm (mg Ir cm ‑2 ) ‑1 . Two-dimensional, two‑phase performance modeling reveals that these thick catalyst layers improve electronic connectivity at low loadings, leading to higher catalyst utilization than a commercial reference. As a result, the core-shell catalyst outperforms the reference in single-cell measurements, achieving 1.77 V at 2 A cm ‑2 at a low loading of 0.31 mg Ir cm ‑2 . During 200 h durability testing, reversible degradation is observed, while irreversible losses remain on par with the reference and the core–shell structure is preserved.
- Open Access
Laying the Foundation for Digital Material Design of Porous Transport Electrodes for PEM Water Electrolysis With Multiscale Tomography
We present the first multiscale identical location tomography of a porous transport electrode (PTE) of a proton exchange membrane water electrolyzer. The tomogram encompasses length scales between micrometer‐thick fibers to nanopores in the catalyst layer (CL) with nanometer‐thin binder coatings on the iridium‐oxide particles. It was recorded using micro‐computed tomography, focused ion beam scanning electron microscopy tomography, scanning transmission electron microscopy and spectroscopy, nitrogen adsorption, and supplemented by a modeling approach. The reconstruction of the PTE reveals a porosity of around 51% of the porous transport layer (PTL) and 61% of the CL. A thorough analysis of the CL allows a comparison with the pristine catalyst powder and a realistic prediction of the transport parameters by modeling the binder thickness to a mean of 7 to 10.5 nm. Further, the overall transport parameters of the PTE are determined. The PTL has a higher permeability in the through‐plane direction, whereas the CL shows isotropic transport properties. This study offers a comprehensive picture of the multiscale structure and properties of a PTE, which allows for a comparison with catalyst‐coated membranes and computer‐aided optimization of future PTEs.
Open AccessLaying the Foundation for Digital Material Design of Porous Transport Electrodes for PEM Water Electrolysis With Multiscale Tomography
We present the first multiscale identical location tomography of a porous transport electrode (PTE) of a proton exchange membrane water electrolyzer. The tomogram encompasses length scales between micrometer‐thick fibers to nanopores in the catalyst layer (CL) with nanometer‐thin binder coatings on the iridium‐oxide particles. It was recorded using micro‐computed tomography, focused ion beam scanning electron microscopy tomography, scanning transmission electron microscopy and spectroscopy, nitrogen adsorption, and supplemented by a modeling approach. The reconstruction of the PTE reveals a porosity of around 51% of the porous transport layer (PTL) and 61% of the CL. A thorough analysis of the CL allows a comparison with the pristine catalyst powder and a realistic prediction of the transport parameters by modeling the binder thickness to a mean of 7 to 10.5 nm. Further, the overall transport parameters of the PTE are determined. The PTL has a higher permeability in the through‐plane direction, whereas the CL shows isotropic transport properties. This study offers a comprehensive picture of the multiscale structure and properties of a PTE, which allows for a comparison with catalyst‐coated membranes and computer‐aided optimization of future PTEs.
- Top Cited PapersOpen Access
- 11 November 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (22) , 9877-9894
Degradation phenomena in PEMWE revealed by correlative electrochemical and nanostructure analysis
Correlative analysis reveals operational mode-dependent PEMWE degradation, highlighting Pt dissolution and Ir oxidation as key durability challenges.
- 11 November 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (22) , 9877-9894
Top Cited PapersOpen AccessDegradation phenomena in PEMWE revealed by correlative electrochemical and nanostructure analysis
Correlative analysis reveals operational mode-dependent PEMWE degradation, highlighting Pt dissolution and Ir oxidation as key durability challenges.
- Open Access
- 6 October 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Laying the foundation for digital material design of porous transport electrodes for PEM water electrolysis with multiscale tomography
We present the first multiscale identical location tomography of a porous transport electrode (PTE) of a proton exchange membrane water electrolyzer. The tomogram encompasses length scales between micrometer-thick fibers to nanopores in the catalyst layer (CL) with nanometer-thin binder coatings on the iridium-oxide particles. It was recorded using micro-computed tomography, focused ion beam scanning electron microscopy tomography, scanning transmission electron microscopy and spectroscopy, nitrogen adsorption, and supplemented by a modeling approach. The reconstruction of the PTE revealed a porosity of around 51% of the porous transport layer (PTL) and 61% of the CL. A thorough analysis of the CL allowed a comparison with the pristine catalyst powder and a realistic prediction of the transport parameters by modeling the binder thickness to a mean of 7 to 10.5 nm. Further, the overall transport parameters of the PTE were determined. The PTL had a higher permeability in the through-plane direction, whereas the CL showed isotropic transport properties. This study offers a comprehensive picture of the multiscale structure and properties of a PTE, which allows for a comparison with catalyst-coated membranes and computer-aided optimization of future PTEs.
- 6 October 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessLaying the foundation for digital material design of porous transport electrodes for PEM water electrolysis with multiscale tomography
We present the first multiscale identical location tomography of a porous transport electrode (PTE) of a proton exchange membrane water electrolyzer. The tomogram encompasses length scales between micrometer-thick fibers to nanopores in the catalyst layer (CL) with nanometer-thin binder coatings on the iridium-oxide particles. It was recorded using micro-computed tomography, focused ion beam scanning electron microscopy tomography, scanning transmission electron microscopy and spectroscopy, nitrogen adsorption, and supplemented by a modeling approach. The reconstruction of the PTE revealed a porosity of around 51% of the porous transport layer (PTL) and 61% of the CL. A thorough analysis of the CL allowed a comparison with the pristine catalyst powder and a realistic prediction of the transport parameters by modeling the binder thickness to a mean of 7 to 10.5 nm. Further, the overall transport parameters of the PTE were determined. The PTL had a higher permeability in the through-plane direction, whereas the CL showed isotropic transport properties. This study offers a comprehensive picture of the multiscale structure and properties of a PTE, which allows for a comparison with catalyst-coated membranes and computer-aided optimization of future PTEs.
- Open Access
- 22 September 2025
- Published by Wiley in ChemSusChem
- Vol. 18 (21) , e202501561
Fluoride‐Induced Corrosion of Stainless Steel: A Case Study for its Application as Proton Exchange Membrane Water Electrolysis Bipolar Plate Material
Stainless steel is a promising material for bipolar plates (BPP) in proton exchange membrane water electrolysis (PEMWE) that could drastically reduce stack costs. However, dissolution of Fe from stainless steel BPP might trigger membrane degradation, which releases fluoride. Fluoride in turn could accelerate stainless steel corrosion. Therefore, the influence of fluoride contamination (namely 0, 1, 5, and 20 ppm in 0.5 mM H 2 SO 4 ) on the dissolution stability of stainless steel (316L) is investigated utilizing a scanning flow cell coupled on‐line to an inductively coupled plasma mass spectrometer (SFC‐ICP‐MS). Fluoride enhances the dissolution exponentially, resulting in enhanced dissolution efficiencies with increased fluoride concentration reaching ≈50% at 20 ppm. Complementary micro and nanostructure analysis (laser profilometry, scanning electron microscopy, and scanning transmission electron microscopy with energy‐dispersive X‐ray spectroscopy) reveals pitting corrosion, whose severity and occurrence appear highly increased with higher fluoride concentration. The results suggest that fluoride impurities in combination with exposed stainless steel, e.g., due to coating imperfections, should be avoided in PEMWE application, as accumulation of impurities of both might lead to a self‐accelerating degradation process.
- 22 September 2025
- Published by Wiley in ChemSusChem
- Vol. 18 (21) , e202501561
Open AccessFluoride‐Induced Corrosion of Stainless Steel: A Case Study for its Application as Proton Exchange Membrane Water Electrolysis Bipolar Plate Material
Stainless steel is a promising material for bipolar plates (BPP) in proton exchange membrane water electrolysis (PEMWE) that could drastically reduce stack costs. However, dissolution of Fe from stainless steel BPP might trigger membrane degradation, which releases fluoride. Fluoride in turn could accelerate stainless steel corrosion. Therefore, the influence of fluoride contamination (namely 0, 1, 5, and 20 ppm in 0.5 mM H 2 SO 4 ) on the dissolution stability of stainless steel (316L) is investigated utilizing a scanning flow cell coupled on‐line to an inductively coupled plasma mass spectrometer (SFC‐ICP‐MS). Fluoride enhances the dissolution exponentially, resulting in enhanced dissolution efficiencies with increased fluoride concentration reaching ≈50% at 20 ppm. Complementary micro and nanostructure analysis (laser profilometry, scanning electron microscopy, and scanning transmission electron microscopy with energy‐dispersive X‐ray spectroscopy) reveals pitting corrosion, whose severity and occurrence appear highly increased with higher fluoride concentration. The results suggest that fluoride impurities in combination with exposed stainless steel, e.g., due to coating imperfections, should be avoided in PEMWE application, as accumulation of impurities of both might lead to a self‐accelerating degradation process.
- Open Access
- 11 June 2025
- Published by Elsevier in Materials Today Sustainability
- Vol. 31
Stainless steel 316L as bipolar plate material in proton exchange membrane water electrolyzer: The influence of potential and temperature on dissolution stability
- 11 June 2025
- Published by Elsevier in Materials Today Sustainability
- Vol. 31
Open AccessStainless steel 316L as bipolar plate material in proton exchange membrane water electrolyzer: The influence of potential and temperature on dissolution stability
- Open Access
- 9 January 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (5)
Porosity‐Zoned Porous‐Transport Layer for Proton‐Exchange Membrane Water Electrolysis by High‐Velocity Flame Spraying
The porous‐transport layer (PTL) is a crucial component in proton‐exchange membrane water electrolyzers (PEMWE) enabling water and gas transport as well as electrically contacting the catalyst layer (CL). To reduce the overall costs of PTLs, a fabrication method by high‐velocity oxy‐fuel (HVOF) spraying is introduced. Free‐standing PTLs are obtained via the application of a titanium coating onto a substrate and its subsequent separation and thermal treatment. The obtained PTLs feature two sides of different roughness and porosity as analyzed and visualized by X‐ray microscopy. This way, the side with decreased porosity (21%) is intended to function as a microporous layer, improving the contact with the CL. The presented fabrication process promises decreased costs compared to vacuum plasma spraying, a simplified, chemical‐free mechanical separation of the PTL from the substrate, and a high scale‐up suitability. In the results, it is demonstrated that HVOF can produce titanium PTLs with low oxygen content. Additionally, PEMWE single‐cell tests demonstrate that the sprayed PTLs perform on par with a commercially available PTL material.
- 9 January 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (5)
Open AccessPorosity‐Zoned Porous‐Transport Layer for Proton‐Exchange Membrane Water Electrolysis by High‐Velocity Flame Spraying
The porous‐transport layer (PTL) is a crucial component in proton‐exchange membrane water electrolyzers (PEMWE) enabling water and gas transport as well as electrically contacting the catalyst layer (CL). To reduce the overall costs of PTLs, a fabrication method by high‐velocity oxy‐fuel (HVOF) spraying is introduced. Free‐standing PTLs are obtained via the application of a titanium coating onto a substrate and its subsequent separation and thermal treatment. The obtained PTLs feature two sides of different roughness and porosity as analyzed and visualized by X‐ray microscopy. This way, the side with decreased porosity (21%) is intended to function as a microporous layer, improving the contact with the CL. The presented fabrication process promises decreased costs compared to vacuum plasma spraying, a simplified, chemical‐free mechanical separation of the PTL from the substrate, and a high scale‐up suitability. In the results, it is demonstrated that HVOF can produce titanium PTLs with low oxygen content. Additionally, PEMWE single‐cell tests demonstrate that the sprayed PTLs perform on par with a commercially available PTL material.
- Open Access
- 14 June 2024
- Published by Wiley in Advanced Science
- Vol. 11 (30) , e2402991
Photodeposition‐Based Synthesis of TiO2@IrOx Core–Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium Loading
The widespread application of green hydrogen production technologies requires cost reduction of crucial elements. To achieve this, a viable pathway to reduce the iridium loading in proton exchange membrane water electrolysis (PEMWE) is explored. Herein, a scalable synthesis method based on a photodeposition process for a TiO2@IrOx core–shell catalyst with a reduced iridium content as low as 40 wt.% is presented. Using this synthesis method, titania support particles homogeneously coated with a thin iridium oxide shell of only 2.1 ± 0.4 nm are obtained. The catalyst exhibits not only high ex situ activity, but also decent stability compared to commercially available catalysts. Furthermore, the unique core–shell structure provides a threefold increased electrical powder conductivity compared to structures without the shell. In addition, the low iridium content facilitates the fabrication of sufficiently thick catalyst layers at decreased iridium loadings mitigating the impact of crack formation in the catalyst layer during PEMWE operation. It is demonstrated that the novel TiO2@IrOx core–shell catalyst clearly outperforms the commercial reference in single‐cell tests with an iridium loading below 0.3 mgIr cm−2 exhibiting a superior iridium‐specific power density of 17.9 kW gIr−1 compared to 10.4 kW gIr−1 for the commercial reference.
- 14 June 2024
- Published by Wiley in Advanced Science
- Vol. 11 (30) , e2402991
Open AccessPhotodeposition‐Based Synthesis of TiO2@IrOx Core–Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium Loading
The widespread application of green hydrogen production technologies requires cost reduction of crucial elements. To achieve this, a viable pathway to reduce the iridium loading in proton exchange membrane water electrolysis (PEMWE) is explored. Herein, a scalable synthesis method based on a photodeposition process for a TiO2@IrOx core–shell catalyst with a reduced iridium content as low as 40 wt.% is presented. Using this synthesis method, titania support particles homogeneously coated with a thin iridium oxide shell of only 2.1 ± 0.4 nm are obtained. The catalyst exhibits not only high ex situ activity, but also decent stability compared to commercially available catalysts. Furthermore, the unique core–shell structure provides a threefold increased electrical powder conductivity compared to structures without the shell. In addition, the low iridium content facilitates the fabrication of sufficiently thick catalyst layers at decreased iridium loadings mitigating the impact of crack formation in the catalyst layer during PEMWE operation. It is demonstrated that the novel TiO2@IrOx core–shell catalyst clearly outperforms the commercial reference in single‐cell tests with an iridium loading below 0.3 mgIr cm−2 exhibiting a superior iridium‐specific power density of 17.9 kW gIr−1 compared to 10.4 kW gIr−1 for the commercial reference.
- Open Access
- 12 March 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Scalable Synthesis of TiO2@IrOx Core-Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium Loading
The widespread application of green hydrogen production technologies requires cost reduction of crucial elements. To achieve this, a viable pathway to reduce the iridium loading in proton exchange membrane water electrolysis (PEMWE) is explored. Herein, we present a scalable synthesis method based on a photodeposition process for a TiO2@IrOx core-shell catalyst with a reduced iridium content as low as 40 wt%. Using this synthesis route, we obtain titania support particles homogeneously coated with a thin iridium oxide shell of only 2.1 ± 0.4 nm. The catalyst exhibits not only high ex situ activity, but also decent stability compared to commercially available catalysts. Furthermore, the unique core-shell structure provides a threefold increased electrical powder conductivity compared to structures without the shell. In addition, the low iridium content facilitates the fabrication of sufficiently thick catalyst layers at decreased iridium loadings mitigating the impact of crack formation in the catalyst layer during PEMWE operation. We demonstrate that the novel TiO2@IrOx core-shell catalyst clearly outperforms the commercial reference in single-cell tests with an iridium loading below 0.3 mgIr cm 2 exhibiting a superior iridium-specific power density of 17.9 kW gIr-1 compared to 10.4 kW gIr-1 for the commercial reference.
- 12 March 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessScalable Synthesis of TiO2@IrOx Core-Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium Loading
The widespread application of green hydrogen production technologies requires cost reduction of crucial elements. To achieve this, a viable pathway to reduce the iridium loading in proton exchange membrane water electrolysis (PEMWE) is explored. Herein, we present a scalable synthesis method based on a photodeposition process for a TiO2@IrOx core-shell catalyst with a reduced iridium content as low as 40 wt%. Using this synthesis route, we obtain titania support particles homogeneously coated with a thin iridium oxide shell of only 2.1 ± 0.4 nm. The catalyst exhibits not only high ex situ activity, but also decent stability compared to commercially available catalysts. Furthermore, the unique core-shell structure provides a threefold increased electrical powder conductivity compared to structures without the shell. In addition, the low iridium content facilitates the fabrication of sufficiently thick catalyst layers at decreased iridium loadings mitigating the impact of crack formation in the catalyst layer during PEMWE operation. We demonstrate that the novel TiO2@IrOx core-shell catalyst clearly outperforms the commercial reference in single-cell tests with an iridium loading below 0.3 mgIr cm 2 exhibiting a superior iridium-specific power density of 17.9 kW gIr-1 compared to 10.4 kW gIr-1 for the commercial reference.