Selina Finger
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Selina Finger has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Andreas Hutzler
Helmholtz Institute Erlangen‐Nürnberg for Renewable Energy (IET‐2) Forschungszentrum Jülich GmbH Erlangen Germany
8 shared publications - Simon Thiele
Forschungszentrum Jülich GmbH, HI ERN (IEK-11)
8 shared publications - Birk Fritsch
Helmholtz Institute Erlangen‐Nürnberg for Renewable Energy (IET‐2) Forschungszentrum Jülich GmbH Erlangen Germany
6 shared publications - Darius Hoffmeister
Forschungszentrum Jülich
6 shared publications - Anna Teressa Sophie Freiberg
Helmholtz-Institute Erlangen-Nürnberg for Renewable Energy (IET-2), Forschungszentrum Jülich GmbH , Cauerstr. 1
5 shared publications - Andreas Körner
Helmholtz Institute Erlangen‐Nürnberg for Renewable Energy (IET‐2) Forschungszentrum Jülich GmbH Erlangen Germany
4 shared publications
Latest Publications
- Open Access
- 30 March 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Revealing Structure-Performance Relations in Core-Shell Catalyst Based PEM Water Electrolyzer Anodes with Low Iridium Loading
Reducing iridium loading in proton exchange membrane water electrolyzer anodes is essential to meet cost targets for large-scale green hydrogen production. Here, we report a photodeposition-based synthesis of TiO 2 @IrO 2 core-shell catalysts with iridium contents as low as 10 wt%. The influence of annealing temperature, iridium content, and iridium loading on structural and electrochemical properties is systematically investigated. An annealing temperature of 450 °C provides the best compromise between activity, conductivity, and stability. Remarkably, even at 10 wt% Ir (≈ 4.5 vol% IrO 2 ), the core-shell architecture maintains high electronic conductivity and mass activity. The low iridium content results in ~18 µm thick catalyst layers at a loading of 0.35 mg Ir cm ‑2 , corresponding to a high thickness factor of 52.0 ± 0.8 µm (mg Ir cm ‑2 ) ‑1 . Two-dimensional, two‑phase performance modeling reveals that these thick catalyst layers improve electronic connectivity at low loadings, leading to higher catalyst utilization than a commercial reference. As a result, the core-shell catalyst outperforms the reference in single-cell measurements, achieving 1.77 V at 2 A cm ‑2 at a low loading of 0.31 mg Ir cm ‑2 . During 200 h durability testing, reversible degradation is observed, while irreversible losses remain on par with the reference and the core–shell structure is preserved.
- 30 March 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessRevealing Structure-Performance Relations in Core-Shell Catalyst Based PEM Water Electrolyzer Anodes with Low Iridium Loading
Reducing iridium loading in proton exchange membrane water electrolyzer anodes is essential to meet cost targets for large-scale green hydrogen production. Here, we report a photodeposition-based synthesis of TiO 2 @IrO 2 core-shell catalysts with iridium contents as low as 10 wt%. The influence of annealing temperature, iridium content, and iridium loading on structural and electrochemical properties is systematically investigated. An annealing temperature of 450 °C provides the best compromise between activity, conductivity, and stability. Remarkably, even at 10 wt% Ir (≈ 4.5 vol% IrO 2 ), the core-shell architecture maintains high electronic conductivity and mass activity. The low iridium content results in ~18 µm thick catalyst layers at a loading of 0.35 mg Ir cm ‑2 , corresponding to a high thickness factor of 52.0 ± 0.8 µm (mg Ir cm ‑2 ) ‑1 . Two-dimensional, two‑phase performance modeling reveals that these thick catalyst layers improve electronic connectivity at low loadings, leading to higher catalyst utilization than a commercial reference. As a result, the core-shell catalyst outperforms the reference in single-cell measurements, achieving 1.77 V at 2 A cm ‑2 at a low loading of 0.31 mg Ir cm ‑2 . During 200 h durability testing, reversible degradation is observed, while irreversible losses remain on par with the reference and the core–shell structure is preserved.
- Open Access
- 14 January 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (1) , 014504
Joint Forces: Time-resolved Analysis of Electrochemical Performance, Nanostructure, and Iridium Dissolution of PEM Water Electrolysis Cells with Low Iridium Loadings under Harsh on/off Cycling Conditions
Although proton exchange membrane water electrolysis technology is deployed at large scale for green hydrogen production, the reliance on iridium as an anode catalyst remains a key challenge for further scalability, competitiveness and sustainability. In this study, the degradation of Ir black and IrO 2 based anode catalyst layers (CL) with varying iridium loadings under harsh on/off cycling is examined. This protocol is considered as an accelerated stress test. A combined approach of operando and post-mortem analysis is applied comprising voltage breakdown analysis, oxygen evolution reaction mass activity determination, scanning transmission electron microscopy, and inductively coupled plasma mass spectrometry. Only minor performance losses are observed, which are particularly pronounced during an initial run-in phase. This phase, however, is followed by increasing iR-free cell voltage values leading to steady-state behavior. The overpotential changes are mostly of kinetic nature, and more evident for Ir black. Time-resolved post-mortem analysis reveals iridium dissolution and migration, with the highest deposition in the cathode CLs after 1 k cycles, coinciding with the run-in phase. However, no measurable effect on end of test performance is detected from anode CL dissolution. These results highlight the need for a combined operando and post-mortem analysis for accurate anode CL degradation analyses.
- 14 January 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (1) , 014504
Open AccessJoint Forces: Time-resolved Analysis of Electrochemical Performance, Nanostructure, and Iridium Dissolution of PEM Water Electrolysis Cells with Low Iridium Loadings under Harsh on/off Cycling Conditions
Although proton exchange membrane water electrolysis technology is deployed at large scale for green hydrogen production, the reliance on iridium as an anode catalyst remains a key challenge for further scalability, competitiveness and sustainability. In this study, the degradation of Ir black and IrO 2 based anode catalyst layers (CL) with varying iridium loadings under harsh on/off cycling is examined. This protocol is considered as an accelerated stress test. A combined approach of operando and post-mortem analysis is applied comprising voltage breakdown analysis, oxygen evolution reaction mass activity determination, scanning transmission electron microscopy, and inductively coupled plasma mass spectrometry. Only minor performance losses are observed, which are particularly pronounced during an initial run-in phase. This phase, however, is followed by increasing iR-free cell voltage values leading to steady-state behavior. The overpotential changes are mostly of kinetic nature, and more evident for Ir black. Time-resolved post-mortem analysis reveals iridium dissolution and migration, with the highest deposition in the cathode CLs after 1 k cycles, coinciding with the run-in phase. However, no measurable effect on end of test performance is detected from anode CL dissolution. These results highlight the need for a combined operando and post-mortem analysis for accurate anode CL degradation analyses.
- Top Cited PapersOpen Access
- 11 November 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (22) , 9877-9894
Degradation phenomena in PEMWE revealed by correlative electrochemical and nanostructure analysis
Correlative analysis reveals operational mode-dependent PEMWE degradation, highlighting Pt dissolution and Ir oxidation as key durability challenges.
- 11 November 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (22) , 9877-9894
Top Cited PapersOpen AccessDegradation phenomena in PEMWE revealed by correlative electrochemical and nanostructure analysis
Correlative analysis reveals operational mode-dependent PEMWE degradation, highlighting Pt dissolution and Ir oxidation as key durability challenges.
- Open Access
- 9 January 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (5)
Porosity‐Zoned Porous‐Transport Layer for Proton‐Exchange Membrane Water Electrolysis by High‐Velocity Flame Spraying
The porous‐transport layer (PTL) is a crucial component in proton‐exchange membrane water electrolyzers (PEMWE) enabling water and gas transport as well as electrically contacting the catalyst layer (CL). To reduce the overall costs of PTLs, a fabrication method by high‐velocity oxy‐fuel (HVOF) spraying is introduced. Free‐standing PTLs are obtained via the application of a titanium coating onto a substrate and its subsequent separation and thermal treatment. The obtained PTLs feature two sides of different roughness and porosity as analyzed and visualized by X‐ray microscopy. This way, the side with decreased porosity (21%) is intended to function as a microporous layer, improving the contact with the CL. The presented fabrication process promises decreased costs compared to vacuum plasma spraying, a simplified, chemical‐free mechanical separation of the PTL from the substrate, and a high scale‐up suitability. In the results, it is demonstrated that HVOF can produce titanium PTLs with low oxygen content. Additionally, PEMWE single‐cell tests demonstrate that the sprayed PTLs perform on par with a commercially available PTL material.
- 9 January 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (5)
Open AccessPorosity‐Zoned Porous‐Transport Layer for Proton‐Exchange Membrane Water Electrolysis by High‐Velocity Flame Spraying
The porous‐transport layer (PTL) is a crucial component in proton‐exchange membrane water electrolyzers (PEMWE) enabling water and gas transport as well as electrically contacting the catalyst layer (CL). To reduce the overall costs of PTLs, a fabrication method by high‐velocity oxy‐fuel (HVOF) spraying is introduced. Free‐standing PTLs are obtained via the application of a titanium coating onto a substrate and its subsequent separation and thermal treatment. The obtained PTLs feature two sides of different roughness and porosity as analyzed and visualized by X‐ray microscopy. This way, the side with decreased porosity (21%) is intended to function as a microporous layer, improving the contact with the CL. The presented fabrication process promises decreased costs compared to vacuum plasma spraying, a simplified, chemical‐free mechanical separation of the PTL from the substrate, and a high scale‐up suitability. In the results, it is demonstrated that HVOF can produce titanium PTLs with low oxygen content. Additionally, PEMWE single‐cell tests demonstrate that the sprayed PTLs perform on par with a commercially available PTL material.
- Open Access
- 14 June 2024
- Published by Wiley in Advanced Science
- Vol. 11 (30) , e2402991
Photodeposition‐Based Synthesis of TiO2@IrOx Core–Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium Loading
The widespread application of green hydrogen production technologies requires cost reduction of crucial elements. To achieve this, a viable pathway to reduce the iridium loading in proton exchange membrane water electrolysis (PEMWE) is explored. Herein, a scalable synthesis method based on a photodeposition process for a TiO2@IrOx core–shell catalyst with a reduced iridium content as low as 40 wt.% is presented. Using this synthesis method, titania support particles homogeneously coated with a thin iridium oxide shell of only 2.1 ± 0.4 nm are obtained. The catalyst exhibits not only high ex situ activity, but also decent stability compared to commercially available catalysts. Furthermore, the unique core–shell structure provides a threefold increased electrical powder conductivity compared to structures without the shell. In addition, the low iridium content facilitates the fabrication of sufficiently thick catalyst layers at decreased iridium loadings mitigating the impact of crack formation in the catalyst layer during PEMWE operation. It is demonstrated that the novel TiO2@IrOx core–shell catalyst clearly outperforms the commercial reference in single‐cell tests with an iridium loading below 0.3 mgIr cm−2 exhibiting a superior iridium‐specific power density of 17.9 kW gIr−1 compared to 10.4 kW gIr−1 for the commercial reference.
- 14 June 2024
- Published by Wiley in Advanced Science
- Vol. 11 (30) , e2402991
Open AccessPhotodeposition‐Based Synthesis of TiO2@IrOx Core–Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium Loading
The widespread application of green hydrogen production technologies requires cost reduction of crucial elements. To achieve this, a viable pathway to reduce the iridium loading in proton exchange membrane water electrolysis (PEMWE) is explored. Herein, a scalable synthesis method based on a photodeposition process for a TiO2@IrOx core–shell catalyst with a reduced iridium content as low as 40 wt.% is presented. Using this synthesis method, titania support particles homogeneously coated with a thin iridium oxide shell of only 2.1 ± 0.4 nm are obtained. The catalyst exhibits not only high ex situ activity, but also decent stability compared to commercially available catalysts. Furthermore, the unique core–shell structure provides a threefold increased electrical powder conductivity compared to structures without the shell. In addition, the low iridium content facilitates the fabrication of sufficiently thick catalyst layers at decreased iridium loadings mitigating the impact of crack formation in the catalyst layer during PEMWE operation. It is demonstrated that the novel TiO2@IrOx core–shell catalyst clearly outperforms the commercial reference in single‐cell tests with an iridium loading below 0.3 mgIr cm−2 exhibiting a superior iridium‐specific power density of 17.9 kW gIr−1 compared to 10.4 kW gIr−1 for the commercial reference.
- Open Access
- 12 March 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Scalable Synthesis of TiO2@IrOx Core-Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium Loading
The widespread application of green hydrogen production technologies requires cost reduction of crucial elements. To achieve this, a viable pathway to reduce the iridium loading in proton exchange membrane water electrolysis (PEMWE) is explored. Herein, we present a scalable synthesis method based on a photodeposition process for a TiO2@IrOx core-shell catalyst with a reduced iridium content as low as 40 wt%. Using this synthesis route, we obtain titania support particles homogeneously coated with a thin iridium oxide shell of only 2.1 ± 0.4 nm. The catalyst exhibits not only high ex situ activity, but also decent stability compared to commercially available catalysts. Furthermore, the unique core-shell structure provides a threefold increased electrical powder conductivity compared to structures without the shell. In addition, the low iridium content facilitates the fabrication of sufficiently thick catalyst layers at decreased iridium loadings mitigating the impact of crack formation in the catalyst layer during PEMWE operation. We demonstrate that the novel TiO2@IrOx core-shell catalyst clearly outperforms the commercial reference in single-cell tests with an iridium loading below 0.3 mgIr cm 2 exhibiting a superior iridium-specific power density of 17.9 kW gIr-1 compared to 10.4 kW gIr-1 for the commercial reference.
- 12 March 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessScalable Synthesis of TiO2@IrOx Core-Shell Catalyst for Proton Exchange Membrane Water Electrolysis with Low Iridium Loading
The widespread application of green hydrogen production technologies requires cost reduction of crucial elements. To achieve this, a viable pathway to reduce the iridium loading in proton exchange membrane water electrolysis (PEMWE) is explored. Herein, we present a scalable synthesis method based on a photodeposition process for a TiO2@IrOx core-shell catalyst with a reduced iridium content as low as 40 wt%. Using this synthesis route, we obtain titania support particles homogeneously coated with a thin iridium oxide shell of only 2.1 ± 0.4 nm. The catalyst exhibits not only high ex situ activity, but also decent stability compared to commercially available catalysts. Furthermore, the unique core-shell structure provides a threefold increased electrical powder conductivity compared to structures without the shell. In addition, the low iridium content facilitates the fabrication of sufficiently thick catalyst layers at decreased iridium loadings mitigating the impact of crack formation in the catalyst layer during PEMWE operation. We demonstrate that the novel TiO2@IrOx core-shell catalyst clearly outperforms the commercial reference in single-cell tests with an iridium loading below 0.3 mgIr cm 2 exhibiting a superior iridium-specific power density of 17.9 kW gIr-1 compared to 10.4 kW gIr-1 for the commercial reference.
- Open Access
- 11 January 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (7) , 3933-3942
Accelerating materials research with a comprehensive data management tool: a case study on an electrochemical laboratory
Introduction of an SQL and Python-based tool for managing research data from acquisition to publication. The method enables FAIR-compatible data management, minimizes user interaction, and provides customizability for diverse research domains.
- 11 January 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (7) , 3933-3942
Open AccessAccelerating materials research with a comprehensive data management tool: a case study on an electrochemical laboratory
Introduction of an SQL and Python-based tool for managing research data from acquisition to publication. The method enables FAIR-compatible data management, minimizes user interaction, and provides customizability for diverse research domains.
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (42) , 2093
Towards Low Iridium Loading in Proton-Exchange Membrane Water Electrolysis: Full-Cell Performance of IrOx@TiO2 Core-Shell Particles in Anode Catalyst Layers
Hydrogen as a promising energy carrier to bridge the gap between supply and demand of renewable energies can be produced by proton-exchange membrane water electrolysis (PEMWE). However, the scarcity of iridium limits the widespread and large-scale implementation of PEMWE. Thus, the state-of-the-art iridium loading for the oxygen evolution reaction (OER) of ~1-2 mgIr·cm-2 must be distinctly reduced.1, 2 A decrease in loading involves a reduction of the catalyst layer (CL) thickness. The reduction is, however, only possible down to a certain threshold (≤ 0.5 mgIr·cm-2), below which the CL shows cracks leading to incomplete connection of the catalyst particles.1, 3 To overcome this issue, we developed a novel catalyst structure with reduced iridium content (< 50 wt% Ir). The synthesized catalyst exhibits a core-shell structure consisting of an insulating TiO2 core (d ≈ 1 µm) coated with iridium oxide (IrOx@TiO2). This optimized structure enables a reduction of the loading while maintaining the thickness and, thus, the electrical connection within the CL. In two related contributions, we demonstrate the suitability of the catalyst by a comprehensive analysis: The first contribution mainly focuses on structural optimization, activity, and stability investigations of the catalyst powder. In this contribution, we optimize the catalyst layer aiming towards high catalyst utilization and in-plane conductivity at iridium loadings below 0.5 mgIr·cm-2. PEMWE full-cell performance is investigated in catalyst-coated membrane (CCM) configuration and the structure and thickness of the CL are characterized by SEM cross-sections. The results of the full-cell tests with our catalyst in comparison to a state-of-the-art IrO2/TiO2 catalyst are shown in Fig. 1. The polarization curve of our catalyst exhibits high OER activity and performance at low loadings (Graph A: 1.76 V @ 1.5 A·cm-2). In comparison to the state-of-the-art catalyst (Graph B), our catalyst outperforms the commercial catalyst in terms of activity. This becomes evident when comparing the HFR-free polarization curves in the low current density region. It could be assigned to a higher catalyst utilization due to the maintained CL thickness or, more likely, to a higher activity of the catalyst itself.1 The performance difference between our and the state-of-the-art catalyst in higher current density regions mainly stems from ohmic losses in the electrode as can be seen from the high frequency resistance (HFR) in Fig. 1. These ohmic losses, however, can supposedly be assigned to the material itself and not to a decreased in-plane conductivity due to a disconnection of parts of the CL. In conclusion, we successfully synthesized an IrOx@TiO2 catalyst with a core-shell structure. This catalyst enables the fabrication of catalyst layers with decreased loadings below 0.5 mgIr·cm-2 while maintaining the catalyst utilization demonstrated in full-cell testing. Therefore, our newly developed catalyst contributes to a scale-up of the PEMWE technology by drastically reducing the demand for the scarce element iridium. Figure 1: Polarization curves, HFR-free polarization curves and HFR values at 80°C (ambient pressure, 100 mlH2O·min-1 on anode) of CCMs fabricated with different anode catalyst types and loading. A: in-house core-shell catalyst with 0.2 mgIr·cm-2 and B: commercial catalyst with 0.3 mgIr·cm-2 (IrO2/TiO2 with 75 wt% Ir, Umicore). References M. Möckl, M. F. Ernst, M. Kornherr, F. Allebrod, M. Bernt, J. Byrknes, C. Eickes, C. Gebauer, A. Moskovtseva and H. A. Gasteiger, J. Electrochem. Soc., 169(6), 64505 (2022). C. Minke, M. Suermann, B. Bensmann and R. Hanke-Rauschenbach, Int. J. of Hydrog. Energy, 46(46), 23581–23590 (2021). M. Bernt, A. Siebel and H. A. Gasteiger, J. Electrochem. Soc., 165(5), F305-F314 (2018). Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (42) , 2093
Towards Low Iridium Loading in Proton-Exchange Membrane Water Electrolysis: Full-Cell Performance of IrOx@TiO2 Core-Shell Particles in Anode Catalyst Layers
Hydrogen as a promising energy carrier to bridge the gap between supply and demand of renewable energies can be produced by proton-exchange membrane water electrolysis (PEMWE). However, the scarcity of iridium limits the widespread and large-scale implementation of PEMWE. Thus, the state-of-the-art iridium loading for the oxygen evolution reaction (OER) of ~1-2 mgIr·cm-2 must be distinctly reduced.1, 2 A decrease in loading involves a reduction of the catalyst layer (CL) thickness. The reduction is, however, only possible down to a certain threshold (≤ 0.5 mgIr·cm-2), below which the CL shows cracks leading to incomplete connection of the catalyst particles.1, 3 To overcome this issue, we developed a novel catalyst structure with reduced iridium content (< 50 wt% Ir). The synthesized catalyst exhibits a core-shell structure consisting of an insulating TiO2 core (d ≈ 1 µm) coated with iridium oxide (IrOx@TiO2). This optimized structure enables a reduction of the loading while maintaining the thickness and, thus, the electrical connection within the CL. In two related contributions, we demonstrate the suitability of the catalyst by a comprehensive analysis: The first contribution mainly focuses on structural optimization, activity, and stability investigations of the catalyst powder. In this contribution, we optimize the catalyst layer aiming towards high catalyst utilization and in-plane conductivity at iridium loadings below 0.5 mgIr·cm-2. PEMWE full-cell performance is investigated in catalyst-coated membrane (CCM) configuration and the structure and thickness of the CL are characterized by SEM cross-sections. The results of the full-cell tests with our catalyst in comparison to a state-of-the-art IrO2/TiO2 catalyst are shown in Fig. 1. The polarization curve of our catalyst exhibits high OER activity and performance at low loadings (Graph A: 1.76 V @ 1.5 A·cm-2). In comparison to the state-of-the-art catalyst (Graph B), our catalyst outperforms the commercial catalyst in terms of activity. This becomes evident when comparing the HFR-free polarization curves in the low current density region. It could be assigned to a higher catalyst utilization due to the maintained CL thickness or, more likely, to a higher activity of the catalyst itself.1 The performance difference between our and the state-of-the-art catalyst in higher current density regions mainly stems from ohmic losses in the electrode as can be seen from the high frequency resistance (HFR) in Fig. 1. These ohmic losses, however, can supposedly be assigned to the material itself and not to a decreased in-plane conductivity due to a disconnection of parts of the CL. In conclusion, we successfully synthesized an IrOx@TiO2 catalyst with a core-shell structure. This catalyst enables the fabrication of catalyst layers with decreased loadings below 0.5 mgIr·cm-2 while maintaining the catalyst utilization demonstrated in full-cell testing. Therefore, our newly developed catalyst contributes to a scale-up of the PEMWE technology by drastically reducing the demand for the scarce element iridium. Figure 1: Polarization curves, HFR-free polarization curves and HFR values at 80°C (ambient pressure, 100 mlH2O·min-1 on anode) of CCMs fabricated with different anode catalyst types and loading. A: in-house core-shell catalyst with 0.2 mgIr·cm-2 and B: commercial catalyst with 0.3 mgIr·cm-2 (IrO2/TiO2 with 75 wt% Ir, Umicore). References M. Möckl, M. F. Ernst, M. Kornherr, F. Allebrod, M. Bernt, J. Byrknes, C. Eickes, C. Gebauer, A. Moskovtseva and H. A. Gasteiger, J. Electrochem. Soc., 169(6), 64505 (2022). C. Minke, M. Suermann, B. Bensmann and R. Hanke-Rauschenbach, Int. J. of Hydrog. Energy, 46(46), 23581–23590 (2021). M. Bernt, A. Siebel and H. A. Gasteiger, J. Electrochem. Soc., 165(5), F305-F314 (2018). Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (42) , 2094
Towards Low Iridium Loading in Proton-Exchange Membrane Water Electrolysis: Scalable Synthesis of IrOx@TiO2 Core-Shell Particles
Proton-exchange membrane water electrolysis (PEMWE) is a promising technology for producing hydrogen from renewable energy sources. However, the high demand for noble metals hinders the widespread adoption of this technology. Especially the anodic catalyst layer is usually manufactured with high loadings of the scarce element iridium, typically ~2 mgIr·cm-2. As an active and stable noble-metal-free alternative to iridium catalysts has yet to be developed, the most viable strategy for the near future development of PEMWE is to reduce iridium loadings as much as possible. Lowering the iridium loading to values below 0.5 mgIr·cm-2, however, often leads to inhomogeneous catalyst layers resulting in disconnected catalyst islands.1, 2 In two related contributions, we report a novel anodic catalyst for PEMWE that can overcome this limitation by forming homogeneous layers even at lower loadings, thus exhibiting high full cell performance. In this first contribution, we synthesized catalysts with less than 50 wt% iridium content to obtain low iridium loadings while maintaining electrical conductivity. The catalyst is based on the IrO2@TiO2 core-shell microparticles introduced in our previous work,3 which we optimized towards their structural and electrochemical properties. The structural properties of these novel catalysts are analyzed by scanning transmission electron microscopy (STEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). Furthermore, the catalytic activity is evaluated by rotating disk electrode (RDE) measurements, and the electrochemical stability is assessed in a scanning flow cell setup combined with an inductively coupled plasma mass spectrometer (SFC-ICP-MS). Our catalysts outperform state-of-the-art materials in terms of mass activity in RDE measurements, while a comparable dissolution stability is achieved, as evidenced by SFC-ICP-MS measurements. In our second contribution, we show a high performance of this novel catalyst in catalyst-coated membrane (CCM) configuration with iridium loadings below the above mentioned threshold of 0.5 mgIr·cm-2. This proves that our novel IrOx@TiO2 particles with low iridium contents enable a significant reduction of iridium for the anode in PEMWE. References: M. Bernt, A. Siebel and H. A. Gasteiger, J. Electrochem. Soc., 165(5), F305-F314 (2018). C. Rozain, E. Mayousse, N. Guillet and P. Millet, Applied Catalysis B: Environmental, 182, 123–131 (2016). C. van Pham, M. Bühler, J. Knöppel, M. Bierling, D. Seeberger, D. Escalera-López, K. J. Mayrhofer, S. Cherevko and S. Thiele, Applied Catalysis B: Environmental, 269, 118762 (2020). Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (42) , 2094
Towards Low Iridium Loading in Proton-Exchange Membrane Water Electrolysis: Scalable Synthesis of IrOx@TiO2 Core-Shell Particles
Proton-exchange membrane water electrolysis (PEMWE) is a promising technology for producing hydrogen from renewable energy sources. However, the high demand for noble metals hinders the widespread adoption of this technology. Especially the anodic catalyst layer is usually manufactured with high loadings of the scarce element iridium, typically ~2 mgIr·cm-2. As an active and stable noble-metal-free alternative to iridium catalysts has yet to be developed, the most viable strategy for the near future development of PEMWE is to reduce iridium loadings as much as possible. Lowering the iridium loading to values below 0.5 mgIr·cm-2, however, often leads to inhomogeneous catalyst layers resulting in disconnected catalyst islands.1, 2 In two related contributions, we report a novel anodic catalyst for PEMWE that can overcome this limitation by forming homogeneous layers even at lower loadings, thus exhibiting high full cell performance. In this first contribution, we synthesized catalysts with less than 50 wt% iridium content to obtain low iridium loadings while maintaining electrical conductivity. The catalyst is based on the IrO2@TiO2 core-shell microparticles introduced in our previous work,3 which we optimized towards their structural and electrochemical properties. The structural properties of these novel catalysts are analyzed by scanning transmission electron microscopy (STEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). Furthermore, the catalytic activity is evaluated by rotating disk electrode (RDE) measurements, and the electrochemical stability is assessed in a scanning flow cell setup combined with an inductively coupled plasma mass spectrometer (SFC-ICP-MS). Our catalysts outperform state-of-the-art materials in terms of mass activity in RDE measurements, while a comparable dissolution stability is achieved, as evidenced by SFC-ICP-MS measurements. In our second contribution, we show a high performance of this novel catalyst in catalyst-coated membrane (CCM) configuration with iridium loadings below the above mentioned threshold of 0.5 mgIr·cm-2. This proves that our novel IrOx@TiO2 particles with low iridium contents enable a significant reduction of iridium for the anode in PEMWE. References: M. Bernt, A. Siebel and H. A. Gasteiger, J. Electrochem. Soc., 165(5), F305-F314 (2018). C. Rozain, E. Mayousse, N. Guillet and P. Millet, Applied Catalysis B: Environmental, 182, 123–131 (2016). C. van Pham, M. Bühler, J. Knöppel, M. Bierling, D. Seeberger, D. Escalera-López, K. J. Mayrhofer, S. Cherevko and S. Thiele, Applied Catalysis B: Environmental, 269, 118762 (2020). Figure 1