YCYekan Chen

Yekan Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yekan Chen has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A 32-Channel Neural-Recording Chip Achieving 117dB Intrinsic-CMRR and 100dB PSRR by CM-Tracking-Dynamic-Power-Rail and CM-Canceling-in-Idle-Phase Techniques

    by Yili Shen, Yekan Chen, Changgui Yang, Tingting He, Chaonan Yu, Jun Zhou, Yuxuan Luo, Kedi Xu, Gang Pan, Yunshan Zhang, et al.

    Multi-channel neural recording enables simultaneous monitoring of neuronal activities across multiple brain regions, while the in-vivo common-mode interference (CMI) significantly degrades the signal quality of implantable neural-recording chips. For a multi-channel neural-recording chip, the total common-mode rejection ratio (T-CMRR) of the analog front-end (AFE) is limited by the input imbalance between the signal electrode and the shared reference electrode, as well as the intrinsic CMRR (I-CMRR) of its circuits. The traditional common-mode replication (CM-REP) technique is only applicable to single-channel systems such as ECG monitoring devices. In addition, conventional pre-amplifier and frequency-controlled differential regulator (FCDR) techniques suffer from gain mismatch and high power consumption, respectively. To address these issues, this work presents a 32-channel neural-recording chip fabricated in a 65 nm CMOS process, which effectively suppresses the CMI in two operational modes: 1) In high-gain mode, the proposed CM-tracking-dynamic-power-rail (CM-TDPR) instrumentation amplifier (IA) achieves 50 GΩ CM input impedance, 117 dB I-CMRR, and 100 dB power supply rejection ratio (PSRR), resulting in a T-CMRR of 87 dB; 2) In low-gain mode, a CM-canceling-in-idle-phase (CM-CIP) technique is proposed to increase the I-CMRR to 102 dB and match the signal-reference input impedance, thereby achieving a 95 dB T-CMRR. In-vivo experiments were conducted on a Sprague-Dawley rat, successfully validating the CMRR performance of the proposed chip.

  • A 0.0251 mm 2 Temperature Sensor Achieving a ±0.25 °C (3σ) Inaccuracy From –40 °C to 125 °C Without Backend Nonlinearity Correction

    by Jiahuai Fan, Yekan Chen, Han Lin, Bo Zhao, Yuxuan Luo

    This paper presents a compact, high-accuracy and scalable on-chip temperature sensor (TS) optimized for low-power embedded applications, such as system-on-chip (SoC) and microprocessor thermal monitoring. The proposed TS employs a capacitive-biased-diode (CBD) structure enhanced by an adaptive discharging period (ADP) technique to achieve high sensitivity and linearity without additional backend calibration. The CBD sensor output is digitized by an oversampling (OS) successive approximation register (SAR) ADC with custom vertical metal-oxide-metal (VMOM) capacitors and a mismatch error shaping (MES) technique, providing high accuracy in a minimized chip area. Additionally, a discharging clock chopping (DCC) technique is proposed to effectively suppresses low-frequency noise with minimal switch noise, while clock boosters are implemented to decrease the ON-resistance of switches, reducing nonlinearity effects. Fabricated in a standard CMOS 180nm process, the sensor occupies only 0.0251 mm2 and consumes $3.6~\mu $ W. It achieves a one-point trimmed inaccuracy of ±0.25°C over a temperature range of −40°C to 125°C.


  • A Capacitive Touch-Sensing Chip With NTF-Alignment Excitation Source and Direct Lock-In ADC

    by Xiangdong Feng, Zhiyu Wang, Yekan Chen, Tianyi Cai, Yangfan Xuan, Weixiao Wang, Yunshan Zhang, Changgui Yang, Zhong Tang, Yuxuan Luo, et al.

    Capacitive touch-screen systems have been widely used in tablets, smartphones, smartwatches, etc. Various sources of noise, such as display and charger noise, limit the energy efficiency of capacitive touch sensors. Traditional noise-reduction methods such as lock-in sensing architecture lead to significant power consumption that shortens the lifetime of battery-powered devices. To address the issue, we propose a noise transfer function (NTF)-alignment technique, in which the excitation signals are precisely placed at the zeros of NTF and the touch-screen system noise lies between them. In addition, a subsequent direct lock-in analog-to-digital converter (ADC) with bandpass noise shaping utilizes the same NTF zeros as the excitation source, resulting in a high signal-to-noise ratio (SNR) throughout the entire signal chain. This simple structure also eliminates bandpass filters, mixers, and low-pass filters in conventional lock-in sensing chains. The proposed techniques are implemented in a 65-nm CMOS process, demonstrating a touch-screen prototype embedded with a 28-channel chip occupying an area of 1.31 mm2. The measured results show that the chip achieves an SNR of 58.9 (for 10-mm $\Phi $ ) and 41.3 dB (for 1-mm $\Phi $ stylus), with only 1.054-mW power dissipated at 120 frames/s. Compared to state-of-the-art designs, the proposed chip achieves the best energy efficiency (27.2 pJ/step).

  • A 430- μ A 68.2-dB-SNR 133-dBSPL-AOP CMOS-MEMS Digital Microphone Based on Electrostatic Force Feedback Control

    by Jiaqi Dong, Qi Zhang, Xinwen Zhang, Yekan Chen, Yili Shen, Bo Zhao, Yuxuan Luo

    This article introduces a high-acoustic-dynamic-range and low-power digital microphone based on the electrostatic force feedback control (EFFC). The proposed design adjusts the sensitivity of the micro-electro-mechanical system (MEMS) by adaptively biasing it at different input amplitudes, thereby extending the dynamic range (DR). The proposed adaptive biasing technique allows the induced electrostatic force to function as a mechanical gain prior to the analog front end (AFE), consequently relaxing the noise performance requirements of the readout electronics. A capacitive feedback (CFB) instrumentation amplifier (IA) with an adjustable gain is employed to effectively reduce the thermal noise introduced by the feedback resistor in conventional resistive feedback (RFB) IAs. A sub-sampling amplitude detector (SSAD) composed of cascaded low-order decimation filters is proposed to achieve efficient acoustic volume detection. The detection results are used to control a fast-settling predictive reference charge pump (PRCP). The PRCP adopts a closed-loop architecture to achieve accurate adjustable bias voltage, with the proposed prediction logic to significantly reduce the settling time. The proposed system achieves a signal-to-noise ratio (SNR) of 68.2 dB at 94 dBSPL and an acoustic overload point (AOP) of 133 dBSPL, with a current consumption of 430 μA at a clock frequency of 3.072 MHz. The measured acoustic DR is 107.2 dB.

  • A Fully Dynamic Event-Driven Capacitive Sensor Interface Circuits Based on Self-Reconfigurable SAR Capacitance-to-Digital Conversion for High-Density Robotic Tactile Sensing

    by Yekan Chen, Tianyi Cai, Yonghong Kuang, Jiaqi Dong, Zipeng Cheng, Bo Zhao, Yuxuan Luo

    Covering robots entirely with electronic skins (e-skins) has been a long-term aspiration. However, the number and density of the tactile sensors are limited by factors such as routing complexity, signal latency, and power consumption. Inspired by neural signal processing, we present a multichannel capacitive interface circuits that read out the sparse tactile signals in an event-driven (ED) manner. A self-reconfigurable successive-approximation-register capacitance-to-digital converter (SR SAR CDC) is proposed to reduce power consumption in passive-sampling (PS) mode and to achieve high resolution in noise-shaping (NS) mode. To support parallel recording in NS data converters, we propose a 2 $^{{N}}$ oversampling-rate (2 $^{{N}}$ -OSR) code division multiplexing (CDM) technique. Besides, an ED inter-integrated circuit (ED-I2C) protocol is proposed to reduce communication data burden and routing complexity. Fabricated in 55-nm CMOS technology, the multichannel capacitive sensor interface occupies a chip area of 2.244 mm $^{\textrm{2}}$ . At a frame rate of 3.47 kHz, this work achieves a measured single-channel signal-to-noise-ratio (SNR) of 51 dB and a power consumption of 7.2 $\mu$ W/Ch in NS mode. The stand-by power can be further reduced to 1.6 $\mu$ W/Ch in PS mode. The ED sensing protocol significantly reduces the data burden for processing and communication, supporting a high-density integration of 4.8 sensors/cm $^{\textrm{2}}$ and 16 sensors/wire.